Difference between revisions of "MultiWii GUI"
From MultiWii
(→Version) |
(→Parameters / Settings) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 15: | Line 15: | ||
==ScreenShot == | ==ScreenShot == | ||
| + | [[File:MultiWiiConf.png|Ground Control Station for a typical Quadropter setup]] | ||
| − | [[File: | + | ===Communications=== |
| + | |||
| + | [[File:Communications.png|Communications Panel]] | ||
| + | *'''V201''': Displays the current version of the firmware on the board (When connected). | ||
| + | *'''SAVE''': Save the current config to a file on disk. | ||
| + | *'''LOAD''': Load the config from file. | ||
| + | *'''PORT COM''': Select the COM port to use, to connect to the MultiWii over USB / FTDI. | ||
| + | |||
| + | |||
| + | ===Parameters / Settings=== | ||
| + | |||
| + | [[File:Parameters.png|Parameters Panel]] | ||
| + | *'''PID Settings''': Set the [[PID|Global]] and [[Altitude_PID|Altitude]] PID. | ||
| + | *'''Expo Settings''': Set the [[RC_rates_%26_expo|Expo and Rate]] settings for Throttle, or Pitch/Roll | ||
| + | *'''Calibration''': Allows you to set the [[Calibration_Compas|Magnetometer]] and [[Calibration_Accelerometer|Accelerometer]] calibration from the GCS. | ||
| + | *'''Read/Write''': Reads/Writes the settings to/from the board. | ||
| + | *'''Feature Grid''': Allows you to tie specific [[Flightmodes|Flight Modes]] or sensors to Tx channels. To set a mode to "Always On", check all three boxes for that mode (Low, Medium and High). | ||
| + | |||
| + | ===Sensors / Debug=== | ||
| + | [[File:Sensors.png|Sensors/Debug Panel]] | ||
| + | |||
| + | |||
| + | ===Output=== | ||
| + | [[File:Output.png|Sensors/OutputSignal Panel]] | ||
| + | |||
| + | |||
| + | ===Input=== | ||
| + | [[File:Input.png|Sensors/Input Signal Panel]] | ||
| + | |||
| + | |||
| + | ===Visualization=== | ||
| + | [[File:Visualization.png|Sensors/Visualization Panel]] | ||
Latest revision as of 14:50, 12 October 2012
Contents
Version
2.0.1
Usage
- Download the current version from multiwii.com
- Unzip the file
- Open the config folder
- If you have windows choose the "Windows" folder and run the .exe file
Current issue
- Some computers have lag spikes
- Checkboxes sometimes won't turn on or off
ScreenShot
Communications
- V201: Displays the current version of the firmware on the board (When connected).
- SAVE: Save the current config to a file on disk.
- LOAD: Load the config from file.
- PORT COM: Select the COM port to use, to connect to the MultiWii over USB / FTDI.
Parameters / Settings
- PID Settings: Set the Global and Altitude PID.
- Expo Settings: Set the Expo and Rate settings for Throttle, or Pitch/Roll
- Calibration: Allows you to set the Magnetometer and Accelerometer calibration from the GCS.
- Read/Write: Reads/Writes the settings to/from the board.
- Feature Grid: Allows you to tie specific Flight Modes or sensors to Tx channels. To set a mode to "Always On", check all three boxes for that mode (Low, Medium and High).
Sensors / Debug
Output
Input
Visualization
