GPS NAV

[wareck]

you have to enable this feature in config.h

//#define USE_MSP_WP

If it's not enable, all navigation feature will not be available in GUI

For the GPS, higher rate you put, higher noise and bad value are sended.
For me, best rate is 57200 bauds with last neo6/neo7 or neo8 gps

[ravid824]

Thank you much.
It resolved my issue.

[Cbronson]

I have the Multiwii pro 3.0 with version 2.3, when I connect to the ez-gui the mission planner disappears. Do I have to comment this out in the sketch file for the mission planner stuff to work. Or does mission planner just not work with 2.3?

You have to have this firmware
http://eosbandi.com/downloads/

I'm having the same problem. I've got the folder you said he needs but what do I do with it?

[GUSHELFER]

We can not always locate in the most appropriate position for a mission , I ask, be possible to rotate the perspective we have on the notebook view GPS ???
if my translator is not good, this is what I mean ...
https://youtu.be/CWBs6ZK03qA

[edsimmons3]

Which software are you using? Do you want map rotation in EZgui?

[GUSHELFER]

Yes !! With EZ -GUI works , but WinGUI 2.3 pre10 ( eosbandi ) ... not that function .

[vukasin]

Hi,

I have tried the GPS mission, but I got strange behavior, this is the mission that have been uploaded to my quad:

but the quad went the other way, and got circling and circling (marked with red) until I flipped off the mission mode, and took the control of quad, because I got scared that the quad would land in the treetops (number 7 is land WP).
[youtube]https://www.youtube.com/watch?v=WPQ-BjGIQJs[/youtube]

That ended badly but that was my fault

Why the quad went there and got circling around, instead flight the mission?

[wareck]

Hi
is your GPS right oriented ?
(if the quad see moving backward until forward, it may do like you)

You nust double check that GPS pointing forward.
For this use wingui and see that dark line point to the right direction

[GUSHELFER]

11ST: poshold ok
The 2nd poshold ok, then gps poshold
The 3rd when gps poshold ok, then rth
The 4th when rth ok, then wp.

[vukasin]

Well, I think I found the cause, Multiwii used only integrated compass on the board, not from the GPS board. When the load (throttle) increase, the compass turns east...almost 90 degress. I need to move the board up and away from power distribution.

Thank you wareck

[ezio]

Well, I think I found the cause, Multiwii used only integrated compass on the board, not from the GPS board. When the load (throttle) increase, the compass turns east...almost 90 degress. I need to move the board up and away from power distribution.

Thank you wareck

Or try to twist the main power wires. It helps a little.

[GUSHELFER]

I directly remove the power distributor plate and directly connect the cables only. of a pair . 2 forward, two back, and both then straight to the lipo , the union of both pairs , by the side of the frame , zero interference mag.me gave very good results !!!

[nickschaos81]

I have a dumb question.... but in the wingui Nav (mission) menu. When you create waypoints , there are 4 boxes that you can add a value to ... but i can find no description or explanation on what they are for or what they do. I have browsed this forum but either missed it or its not pointed out. Any Ideas?

Side note, just installed patriks multiwii airplane, it works great. I have no complaints .... yet.
Also curious if patrik emilsson has a current version of code for his multwii head tracker. All links on his site point to 404 , would like to try to get a multiwii pro to run headtracking.
Why? because i have one thats just sitting , and why not... cool project i think.
thanks

[Berlin_Crash_Pilot]

can anyone give me an hint where the WinGUI does store the stallite map files if I hit the FETCH MAP button ?

Thanks in advance.

[synersignart]

Question guys is EOSBandi still active . I've notice some maps are breaking up.