MultiWii EZ-GUI
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Re: MultiWii EZ-GUI
What are peoples setups to get the best range? What BT modules and antenna are people using?
Re: MultiWii EZ-GUI
NNagib wrote:@ezio, I have found two bugs:
1. in the program, when the altitude is negative it is written correctly in the dashboard, but text-to-speech doesn't pronounce minus, it says "altitude is 15 meters" when the real altitude is -15m.
2. log converter crashes in an attempt to open a log file which contains arm-disarm sequence with no flight data in between (at least this is the case on my Note 3).
Can you check for this?
Tnx!
If there is a possibly to send crash report please do it.
Could you send me this log file?
Btw how are you create it?
Re: MultiWii EZ-GUI
I don't have crash log (where is it stored?), and log data file is here
http://www.filedropper.com/multiwiilog20140821182004
log is created in ez-gui, automatically when the copter is being armed
http://www.filedropper.com/multiwiilog20140821182004
log is created in ez-gui, automatically when the copter is being armed
Re: MultiWii EZ-GUI
NNagib wrote:I don't have crash log (where is it stored?), and log data file is here
http://www.filedropper.com/multiwiilog20140821182004
log is created in ez-gui, automatically when the copter is being armed
Should be ok now after update.
Re: MultiWii EZ-GUI
EZ GUI log and Virb Edit Quick Test
http://youtu.be/LJXpZh7vU4g
http://youtu.be/LJXpZh7vU4g
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
@ Ezio.
Question: Wich motor is Motor 1, 2, 3 & 4 in the CSV File.
I guess:
D2 - Motor 1 - Front Left (ClockWise)
D3 - Motor 2 - Rear Right (ClockWise)
D5 - Motor 3 - Front Right (CounterClockWise)
D6 - Motor 4 - Rear Left (CounterClockWise)
But maybe i'm wrong
Looking into the CSV File....
Motor 2 and 3 are running fast.
Motor 1 and 4 are running slow.
I weighted the Quad...each corner has a weight of about 525 Gram (+- 10 difference between the motors).
I Also have this Yaw issue:
Yaw Right is a bit of a problem
Yaw left is Okay.
I think the alignment of the motor is a bit off.
That can also explain why 2 motors are Higher and 2 lower.
But in that case M1 M2 M3 M4 are different then what i said before.
But Maybe the motor mapping in EZ Gui is as followed:
Motor 1 - Front Left (CW)
Motor 2 - Front Right (CCW)
Motor 3 - Rear Left (CCW)
Motor 4 - Rear Right (CW)
Motor 2 and 3 are running fast. (to counteract MIS-alignement)...and causing a Bad Yaw Right...since the motor is already running pretty High!
can you help me out with the motors??
Question: Wich motor is Motor 1, 2, 3 & 4 in the CSV File.
I guess:
D2 - Motor 1 - Front Left (ClockWise)
D3 - Motor 2 - Rear Right (ClockWise)
D5 - Motor 3 - Front Right (CounterClockWise)
D6 - Motor 4 - Rear Left (CounterClockWise)
But maybe i'm wrong
Looking into the CSV File....
Motor 2 and 3 are running fast.
Motor 1 and 4 are running slow.
I weighted the Quad...each corner has a weight of about 525 Gram (+- 10 difference between the motors).
I Also have this Yaw issue:
Yaw Right is a bit of a problem
Yaw left is Okay.
I think the alignment of the motor is a bit off.
That can also explain why 2 motors are Higher and 2 lower.
But in that case M1 M2 M3 M4 are different then what i said before.
But Maybe the motor mapping in EZ Gui is as followed:
Motor 1 - Front Left (CW)
Motor 2 - Front Right (CCW)
Motor 3 - Rear Left (CCW)
Motor 4 - Rear Right (CW)
Motor 2 and 3 are running fast. (to counteract MIS-alignement)...and causing a Bad Yaw Right...since the motor is already running pretty High!
can you help me out with the motors??
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
After a Check (tilt forwards backwards sideway's right and legt).
my conclusion is:
M1 - Rear Right (CW)
M2 - Front Right (CCW)
M3 - Rear Left (CCW)
M4 - Front Left (CW)
my conclusion is:
M1 - Rear Right (CW)
M2 - Front Right (CCW)
M3 - Rear Left (CCW)
M4 - Front Left (CW)
Re: MultiWii EZ-GUI
exactly the same (in my case)
Re: MultiWii EZ-GUI
Hello,
can someone report a working WIFI<->Serial Adapter?
Regards,
Hendrik
can someone report a working WIFI<->Serial Adapter?
Regards,
Hendrik
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re:
ezio wrote:Logs converter displays the average for each motor too
hmm, I cannot Scroll easy to the Motor Average...(it was out of visible screen)
Maybe add a Button to view it full screen.
Scrolling doesn't work that well for me unfortunately.
Don't you think M1 M2 M3 M4 are weird setup in Multiwii?
I would think that the order of Motor should be compliant with the OutputNumbers (to make things clear, and Standard)?
i was surprised after checking that Motor 1 is Rear Left.
Re: MultiWii EZ-GUI
ezio, can you (or someone else) explain FrSky support in EZ-GUI? I don't understand how it works. Tnx!
Re: MultiWii EZ-GUI
henfri wrote:can someone report a working WIFI<->Serial Adapter?
Is noone using Wifi to connect?
Greetings,
Hendrik
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
No Wifi >> But Bluetooth with a little Mod... to extend the range.
@ EZIO.
Today, 5 Flights....4time a Empty EL1 file :/ (autologging enabled)
any clue?
the app was working, and giving me voltages etc.
@ EZIO.
Today, 5 Flights....4time a Empty EL1 file :/ (autologging enabled)
any clue?
the app was working, and giving me voltages etc.
Re: MultiWii EZ-GUI
NNagib wrote:ezio, can you (or someone else) explain FrSky support in EZ-GUI? I don't understand how it works. Tnx!
Support for FrSky hasn't been updated for a while now and I will probably remove it in the future.
It works like this:
You connect multiwii board to frsky receiver (it had to be one with telemetry. And the connection has to be done via signal inverter).
On the ground you connect Bluetooth module to your frsky transmitter (also via the converter)
And you connect this BT module to the EZ-GUI.
It gives you very slow ,ONE way transmission. EZ-GUI can read few parameters from the bord and signal strength.
Also the support is not build into multiwii by default. You have to add it manually.
Re: MultiWii EZ-GUI
Hypermobile wrote:No Wifi >> But Bluetooth with a little Mod... to extend the range.
@ EZIO.
Today, 5 Flights....4time a Empty EL1 file :/ (autologging enabled)
any clue?
the app was working, and giving me voltages etc.
What does it means that the files are empty? Could you send one?
I tested logging quite hard during last flights and it never failed me.
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
ezio wrote:Hypermobile wrote:No Wifi >> But Bluetooth with a little Mod... to extend the range.
@ EZIO.
Today, 5 Flights....4time a Empty EL1 file :/ (autologging enabled)
any clue?
the app was working, and giving me voltages etc.
What does it means that the files are empty? Could you send one?
I tested logging quite hard during last flights and it never failed me.
Yep 4 empty files. I checked them on the PC.
and if there is a Empty EL1 file crashed in the Log App!
(i sent a Crash report from the app...but i guess that could be worthless).
The video was pretty nice tho :p
Re: MultiWii EZ-GUI
could you tell me what you did with the app during the flight? (PID settings etc)
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
Nothing special, no tuning.
i guess it was:
* Connect bluetooth (5 times or so); Till it was connected.
* ARM (sounds beep) 'Logging enabled'
* Dashboard 2; and the other time maybe Menu screen...since it says battery voltage etc.
* Disarm (logging disabled)
* Exit app
Resulted in a empty file...while the same procedure indoor (same day) did work.
early this week i took a picture outdoors, and that worked too.
so i haven't found a consistency unfortunately
i guess it was:
* Connect bluetooth (5 times or so); Till it was connected.
* ARM (sounds beep) 'Logging enabled'
* Dashboard 2; and the other time maybe Menu screen...since it says battery voltage etc.
* Disarm (logging disabled)
* Exit app
Resulted in a empty file...while the same procedure indoor (same day) did work.
early this week i took a picture outdoors, and that worked too.
so i haven't found a consistency unfortunately
Re: MultiWii EZ-GUI
Question ?
MultiWii EZ GUI works with MultiWii 2.3 navb5 ? because everytime i use it after my copter want to fly by himself... throttle goes out of control and i need to stop the engine ??
So tell me what is the good version of EZ GUI to use with MultiWii 2.3 navb5 ? PLEASE !!
MultiWii EZ GUI works with MultiWii 2.3 navb5 ? because everytime i use it after my copter want to fly by himself... throttle goes out of control and i need to stop the engine ??
So tell me what is the good version of EZ GUI to use with MultiWii 2.3 navb5 ? PLEASE !!
Re: MultiWii EZ-GUI
tryss wrote:Question ?
MultiWii EZ GUI works with MultiWii 2.3 navb5 ? because everytime i use it after my copter want to fly by himself... throttle goes out of control and i need to stop the engine ??
So tell me what is the good version of EZ GUI to use with MultiWii 2.3 navb5 ? PLEASE !!
It should. But most of the testing was done on regular MW 2.3 and navb7.
So maybe update the firmware to b7.
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
Maybe it has something to do with my OLD WindowsPhone running Android.
But the easy fix...IF the file is Empty...Catch it instead of a crashing app.
But the easy fix...IF the file is Empty...Catch it instead of a crashing app.
Re: MultiWii EZ-GUI
Hypermobile wrote:Maybe it has something to do with my OLD WindowsPhone running Android.
But the easy fix...IF the file is Empty...Catch it instead of a crashing app.
I will look at it today. Could you send me the log which crash the app?
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
I sent a Crashreport, so maybe you could find that @ Playstore??
but to recreate the bug i got...
Create a empty *.El1 and Open that file in LOGs.
That was my crash.
Reason why it's emty is unknown yet.
It has functioned and will function again.
but to recreate the bug i got...
Create a empty *.El1 and Open that file in LOGs.
That was my crash.
Reason why it's emty is unknown yet.
It has functioned and will function again.
-
- Posts: 36
- Joined: Sat Jul 06, 2013 10:31 am
Re: MultiWii EZ-GUI
ezio wrote:NNagib wrote:ezio, can you (or someone else) explain FrSky support in EZ-GUI? I don't understand how it works. Tnx!
Support for FrSky hasn't been updated for a while now and I will probably remove it in the future.
It works like this:
You connect multiwii board to frsky receiver (it had to be one with telemetry. And the connection has to be done via signal inverter).
On the ground you connect Bluetooth module to your frsky transmitter (also via the converter)
And you connect this BT module to the EZ-GUI.
It gives you very slow ,ONE way transmission. EZ-GUI can read few parameters from the bord and signal strength.
Also the support is not build into multiwii by default. You have to add it manually.
Please please please. Do not remove it from EZ-GUI... did i mention Please ?
Re: MultiWii EZ-GUI
Hello there!
I'm a happy EZ-GUI user, this app is very very useful once on the field.
However I encounter an issue that makes me uncomfortable with the navigation feature: the maps shows the drone position in Africa, while it is actually in the middle of Europe.
It looks like somehow it takes the wrong hemisphere. Anyone had this issue?
The position hold and return to home work perfectly, so in my opinion this is more an interpretation issue of the received GPS info by the app.
For now I won't use the mission planer as this could start a runaway...
I'm a happy EZ-GUI user, this app is very very useful once on the field.
However I encounter an issue that makes me uncomfortable with the navigation feature: the maps shows the drone position in Africa, while it is actually in the middle of Europe.
It looks like somehow it takes the wrong hemisphere. Anyone had this issue?
The position hold and return to home work perfectly, so in my opinion this is more an interpretation issue of the received GPS info by the app.
For now I won't use the mission planer as this could start a runaway...
Re: MultiWii EZ-GUI
Hi,
I got MultiWii EZ GUI 3.106.163 running on Google Nexus mobile (previous Model from LG).
When I display Dashboard 2 (Anzeige 2) sometimes I could NOT leave the Dashboard - also the softkeys won't display?
Can someone help me please?
Best regards,
Derget
I got MultiWii EZ GUI 3.106.163 running on Google Nexus mobile (previous Model from LG).
When I display Dashboard 2 (Anzeige 2) sometimes I could NOT leave the Dashboard - also the softkeys won't display?
Can someone help me please?
Best regards,
Derget
Re: MultiWii EZ-GUI
Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?
Re: MultiWii EZ-GUI
msev wrote:Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?
There are some problems with vel. I will try to fix it asap. Cli works.
Re: MultiWii EZ-GUI
Derget wrote:Hi,
I got MultiWii EZ GUI 3.106.163 running on Google Nexus mobile (previous Model from LG).
When I display Dashboard 2 (Anzeige 2) sometimes I could NOT leave the Dashboard - also the softkeys won't display?
Can someone help me please?
Best regards,
Derget
Slide you finger from the upper edge of the screen down to show the buttons.
Re: MultiWii EZ-GUI
ezio wrote:msev wrote:Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?
There are some problems with vel. I will try to fix it asap. Cli works.
When connected over BT to naze32 with baseflight...CLI disappears from second screen.
Re: MultiWii EZ-GUI
scrat wrote:ezio wrote:msev wrote:Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?
There are some problems with vel. I will try to fix it asap. Cli works.
When connected over BT to naze32 with baseflight...CLI disappears from second screen.
Enable baseflight support in settings.
And for now please do not use the PID with naze32. It can set VEL to wrong values.
Re: MultiWii EZ-GUI
scrat wrote:ezio wrote:msev wrote:Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?
There are some problems with vel. I will try to fix it asap. Cli works.
When connected over BT to naze32 with baseflight...CLI disappears from second screen.
Enable baseflight support in settings.
And for now please do not use the PID with naze32. It can set VEL to wrong values.
Re: MultiWii EZ-GUI
ezio wrote:scrat wrote:Enable baseflight support in settings.
And for now please do not use the PID with naze32. It can set VEL to wrong values.
Thanks. About VEL...ask me how I know. Nothing broken...just alt hold doesn't work.
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
@ Ezio
Two idea's for you EZGui.
1) Intergrated info from http://www.n3kl.org/sun/noaa.html (Geomagnetic situation)....to check if Flying on GPS is a good idea or not.
(top Left). Today it says Geomagnetic Storm....and if i look to my GPS it's floating around...so not that good.
2) A screen to Popup user specified Pre-Flight Checks (and post flight checks).
i've made a list on paper...but PAPER is old skool.
Sometimes i forget my switch off my Video power....of forget to Record the GoPro.
Nice to have a screen full of reminders.
i'm getting old
Two idea's for you EZGui.
1) Intergrated info from http://www.n3kl.org/sun/noaa.html (Geomagnetic situation)....to check if Flying on GPS is a good idea or not.
(top Left). Today it says Geomagnetic Storm....and if i look to my GPS it's floating around...so not that good.
2) A screen to Popup user specified Pre-Flight Checks (and post flight checks).
i've made a list on paper...but PAPER is old skool.
Sometimes i forget my switch off my Video power....of forget to Record the GoPro.
Nice to have a screen full of reminders.
i'm getting old
Re: MultiWii EZ-GUI
Hypermobile wrote:@ Ezio
Two idea's for you EZGui.
1) Intergrated info from http://www.n3kl.org/sun/noaa.html (Geomagnetic situation)....to check if Flying on GPS is a good idea or not.
(top Left). Today it says Geomagnetic Storm....and if i look to my GPS it's floating around...so not that good.
2) A screen to Popup user specified Pre-Flight Checks (and post flight checks).
i've made a list on paper...but PAPER is old skool.
Sometimes i forget my switch off my Video power....of forget to Record the GoPro.
Nice to have a screen full of reminders.
i'm getting old
Hi
Actually I thought about your ideas too.
I like the first one.
The check list - I don't know. It will be different for different people.
-
- Posts: 94
- Joined: Mon Jan 13, 2014 8:53 pm
Re: MultiWii EZ-GUI
I see That PreFlight as....
another button....and just a Plain screen which you can edit...and save..
so you can recall you OWN made PreFlight stuff.
instead of a piece of paper.
another button....and just a Plain screen which you can edit...and save..
so you can recall you OWN made PreFlight stuff.
instead of a piece of paper.
Re: MultiWii EZ-GUI
Hi!
Little up for my question, if someone knows how to solve this issue?
Little up for my question, if someone knows how to solve this issue?
BuBu wrote:the maps shows the drone position in Africa, while it is actually in the middle of Europe.
It looks like somehow it takes the wrong hemisphere. Anyone had this issue?
Re: MultiWii EZ-GUI
BuBu wrote:Hi!
Little up for my question, if someone knows how to solve this issue?BuBu wrote:the maps shows the drone position in Africa, while it is actually in the middle of Europe.
It looks like somehow it takes the wrong hemisphere. Anyone had this issue?
What coordinates are displayed in GPS section?
What version of MW do you use?
Do you have gps on board?
Re: MultiWii EZ-GUI
ezio wrote:What coordinates are displayed in GPS section?
What version of MW do you use?
Do you have gps on board?
Hello, I'm currently absent but I'll try again to see the coordinates and post more info ASAP. It's MW 2.3 and the GPS is a U-Blox Lea-6h on a separate board.
The position hold and RTH work very well, it's just the map that shows somewhere else, far in the south hemisphere.
Re: MultiWii EZ-GUI
BuBu wrote:ezio wrote:What coordinates are displayed in GPS section?
What version of MW do you use?
Do you have gps on board?
Hello, I'm currently absent but I'll try again to see the coordinates and post more info ASAP. It's MW 2.3 and the GPS is a U-Blox Lea-6h on a separate board.
The position hold and RTH work very well, it's just the map that shows somewhere else, far in the south hemisphere.
I leave also in the middle of Europe and it works perfectly fine.
Position like this is shown when the position is unknown.
Re: MultiWii EZ-GUI
scrat wrote:ezio wrote:scrat wrote:Enable baseflight support in settings.
And for now please do not use the PID with naze32. It can set VEL to wrong values.
Thanks. About VEL...ask me how I know. Nothing broken...just alt hold doesn't work.
It is fixed beta version. I also added VEL to pid settings
Re: MultiWii EZ-GUI
Thanks man!
Re: MultiWii EZ-GUI
Bart,
2 weeks ago I flew my first Quadcopter.
Yesterday I received my bluetooth module, hooked it up to my quad, downloaded and tried your app.
Love it and purchased the upgrade to support your effort.
Thanks!
Leo
2 weeks ago I flew my first Quadcopter.
Yesterday I received my bluetooth module, hooked it up to my quad, downloaded and tried your app.
Love it and purchased the upgrade to support your effort.
Thanks!
Leo
Re: MultiWii EZ-GUI
might be a stupid question, but can the CLI feature in EZ-GUI be used to send raw MSP_SET* messages? Or, does it only support the baseflight CLI features?
Re: MultiWii EZ-GUI
rubadub wrote:might be a stupid question, but can the CLI feature in EZ-GUI be used to send raw MSP_SET* messages? Or, does it only support the baseflight CLI features?
Technically it is possible. Everything you put there is send to the flight control board. But it will be very difficult to do it as you have to write entire message using ASCII.
Re: MultiWii EZ-GUI
Leo wrote:Bart,
2 weeks ago I flew my first Quadcopter.
Yesterday I received my bluetooth module, hooked it up to my quad, downloaded and tried your app.
Love it and purchased the upgrade to support your effort.
Thanks!
Leo
Thank you
Re: MultiWii EZ-GUI
ezio wrote:rubadub wrote:might be a stupid question, but can the CLI feature in EZ-GUI be used to send raw MSP_SET* messages? Or, does it only support the baseflight CLI features?
Technically it is possible. Everything you put there is send to the flight control board. But it will be very difficult to do it as you have to write entire message using ASCII.
how difficult would it be to add such a feature? BTW, I'm a paying customer, in case it makes a difference...