What FC recomended for MultiWii 2.4 ?

Post Reply
flyespen
Posts: 1
Joined: Sun Apr 12, 2015 5:05 pm

What FC recomended for MultiWii 2.4 ?

Post by flyespen »

Hi Rooki asks:

I have a couple of boards I wonder if I can use one of these to work with 2.4 ??
Both boards below is currently running MPNG 3.1.5 -R2 but I think about going back to MultiWii 2.4 Advice me please :)

1) (MultiWii PRO_RED board from HK)
• SMD component design with Atmega2560
• ITG3205 Triple Axis Gyro
• BMA180 Accelerometer
• BMP085 Barometer
• HMC5883L Magnetometer
• Servo output for camera pitch and roll control
• Supports direct connection of GPS module (MTK 3329 GPS module included)
• On-board USB connection for programming

2) (AIO PRO_BLUE board from HK)
• Supported MegaPirateNG and MultiWii firmware
• Up to 8-axis motor output
• 8 input channels for standard receiver
• 4 serial ports for debug/Bluetooth Module/OSD/GPS/telemetry
• 2 servos output for PITCH and ROLL gimbal system
• 1 servo output to trigger a camera button
• 6 Analog output for extend device
• A I2C port for extend sensor or device
• Separate 3.3V and 5V LDO voltage regulator
• ATMega 2560 Microcontroller
• MPU6050 6 axis gyro/accel with Motion Processing Unit
• HMC5883L 3-axis digital magnetometer
• MS5611-01BA01 highprecision altimeter
• FT232RQ USB-UART chip and Micro USB receptacle
• On board logic level converter

User avatar
Leo
Posts: 372
Joined: Wed Sep 17, 2014 7:01 am
Location: Germany
Contact:

Re: What FC recomended for MultiWii 2.4 ?

Post by Leo »

I'd go for #2 simply because it has a MS5611 Baro which has better resolution. Get a cheap uBlox GPS with on-board MAG and your all set to go :)

QuadBow
Posts: 532
Joined: Fri Jan 04, 2013 10:06 am

Re: What FC recomended for MultiWii 2.4 ?

Post by QuadBow »

Both boards are not predefined for multiwii (in file config.h).
Hopefully, HK provides an usable manual how to set up the boards.
The second board provides the more modern gyro/acc device MPU6050.
So, that would be my recommendation, too.

User avatar
Leo
Posts: 372
Joined: Wed Sep 17, 2014 7:01 am
Location: Germany
Contact:

Re: What FC recomended for MultiWii 2.4 ?

Post by Leo »

I don't have either boards but if I was a betting man then all you would have to do for the #2 board is to activate "#define CRIUS_AIO_PRO" in the config.h file.

If not then it easy to configure the individual modules.

FengShuiDrone
Posts: 234
Joined: Wed Dec 24, 2014 1:20 am
Location: ......

Re: What FC recomended for MultiWii 2.4 ?

Post by FengShuiDrone »

.
Last edited by FengShuiDrone on Fri Aug 07, 2015 11:58 pm, edited 1 time in total.

kenl
Posts: 17
Joined: Tue Jun 17, 2014 1:03 pm

Re: What FC recomended for MultiWii 2.4 ?

Post by kenl »

I've got the crius AIO pro in my newly built hex with an external Mag. I can't get 2.4 to recognise the mag yet 2.3 does so I have reverted to 2.3, is there something obvious that I may doing wrong?

User avatar
Leo
Posts: 372
Joined: Wed Sep 17, 2014 7:01 am
Location: Germany
Contact:

Re: What FC recomended for MultiWii 2.4 ?

Post by Leo »

kenl wrote:I've got the crius AIO pro in my newly built hex with an external Mag. I can't get 2.4 to recognise the mag yet 2.3 does so I have reverted to 2.3, is there something obvious that I may doing wrong?


Wrong thread....

Look here for the answer: http://www.multiwii.com/forum/viewtopic.php?f=6&t=6079

Post Reply