Hello ,
Ive got the arduino pro mini 382 end origional wmp sensor
On à warthox black board
Do the wmp got à acc sensor ?
On the gui it says acc roll 5 , acc pitch 5 acc z 500
When i move the quad nothing changes i run on THE 1.8 config
My biggest problem is wen THE quad flys end i do forward pitch end let go off THE stick
The quad keeps going forward
Esc 18amp
Motors keda 1130 kv
Props 8x4.7
Thanks
Question
Re: Question
Dimitri, the WM+ is Gyros only.
You say you have ACC values, do you have ACC in Green in the GUI?
If so you have an ACC of some kind and you just have to assign switches to turn them on.
Without ACCs the copter graphic in the GUI will not move.
If the ACC is not green, check to see if there is any stray solder or a jumper wire where the NK would mount to the WM+.
I then would reload the software to get those ACC values out of there.
Back to the way it flys….Without ACCs it will not return to LEVEL on its own so it sounds like it if flying correctly.
You say you have ACC values, do you have ACC in Green in the GUI?
If so you have an ACC of some kind and you just have to assign switches to turn them on.
Without ACCs the copter graphic in the GUI will not move.
If the ACC is not green, check to see if there is any stray solder or a jumper wire where the NK would mount to the WM+.
I then would reload the software to get those ACC values out of there.
Back to the way it flys….Without ACCs it will not return to LEVEL on its own so it sounds like it if flying correctly.
Re: Question
Hi,
please try to upload the more recent version (1.9 ) as this fixes some i2c errors.
To get you going with sensors.
WMP+ = ITG3200 Gyro
Nunchuck = ACC (dont know wich chip, as i don´t own it)
If you uncommented the Nunchuck but do not have one connected may be a problem.
You may fly without ACC, but only in acro mode (Behaving like a normal copter)
If you choose to add ACC it will recover its level (levelmode)(behaving like a coax helicopter)
hope this helped a bit!
maybe its worth to have a look here for some basic informations -> http://www.multiwii.com/faq
greetz
Noc
btw. if you do not already have an acc, take something like the BMA180, as its resolution is far better then nunchucks resolution. (as far as i know)
please try to upload the more recent version (1.9 ) as this fixes some i2c errors.
To get you going with sensors.
WMP+ = ITG3200 Gyro
Nunchuck = ACC (dont know wich chip, as i don´t own it)
If you uncommented the Nunchuck but do not have one connected may be a problem.
You may fly without ACC, but only in acro mode (Behaving like a normal copter)
If you choose to add ACC it will recover its level (levelmode)(behaving like a coax helicopter)
hope this helped a bit!
maybe its worth to have a look here for some basic informations -> http://www.multiwii.com/faq
greetz
Noc
btw. if you do not already have an acc, take something like the BMA180, as its resolution is far better then nunchucks resolution. (as far as i know)
Last edited by Noctaro on Tue Feb 07, 2012 4:34 pm, edited 1 time in total.
Re: Question
thanks noctaro end wayne for replying to my post
end also for the tips i was braking my head over it
greetz Dimitri
thanks for the help !!!
end also for the tips i was braking my head over it
greetz Dimitri
thanks for the help !!!
Re: Question
you are welcome! 
feel free to ask if you got further questions!
greetz
Noc
btw. wayne, i did not want to replay your post, seems i just was typing at the same time
feel free to ask if you got further questions!
greetz
Noc
btw. wayne, i did not want to replay your post, seems i just was typing at the same time