CJMCU microquad board

SK1701
Posts: 4
Joined: Mon Jun 15, 2015 4:55 pm

Re: CJMCU microquad board

Post by SK1701 »

Which pin are you using for the power input to the receiver? There is a regulated 3.3V power supply above the programming pins that might help.

Arakon
Posts: 196
Joined: Thu Jul 17, 2014 2:22 pm

Re: CJMCU microquad board

Post by Arakon »

Yep, figured that out literally a minute before your posting. Seems to do the trick.

Arakon
Posts: 196
Joined: Thu Jul 17, 2014 2:22 pm

Re: CJMCU microquad board

Post by Arakon »

She flies.. however, after a few seconds, yaw will start either continue rotating (left) or when yawing right, it will pull hard to the back and crash. Up until then it flies stable.

bickie
Posts: 2
Joined: Tue Nov 26, 2013 9:47 am

Re: CJMCU microquad board

Post by bickie »

I had the same "motors won't spin" issue and replaced all the FETs with these: http://au.rs-online.com/web/p/mosfet-tr ... s/6106693/

Fiddly work, but motors all spin up perfectly now. Not 100% sure if they're exactly the right ratings for voltage range/etc but will test motors outputs with multimeter soon.

badzz
Posts: 2
Joined: Fri Jun 19, 2015 10:31 pm

CJMCU microquad board

Post by badzz »

bickie wrote:I had the same "motors won't spin" issue and replaced all the FETs with these: http://au.rs-online.com/web/p/mosfet-tr ... s/6106693/

Fiddly work, but motors all spin up perfectly now. Not 100% sure if they're exactly the right ratings for voltage range/etc but will test motors outputs with multimeter soon.

It worked for me and flies OK but it seems to consume a lot of amps. I will setup a test bench to check the exact consumption

Arakon
Posts: 196
Joined: Thu Jul 17, 2014 2:22 pm

Re: CJMCU microquad board

Post by Arakon »

Replaced the motors and it seems to fly okay now.
GLB refunded me 10$, btw.

fishpepper
Posts: 1
Joined: Mon Jul 13, 2015 4:27 pm

Re: CJMCU microquad board

Post by fishpepper »

Hi!

I had the same issue...
A quick trick for those unfamilar with smd soldering: Put a big blob of solder
all over the (wrong) mosfet or transistor for removal. This will probably destroy it (we are not going to use it so who cares...).
The big solder blob will heat all pads through the mosfets case and you can swipe it to the side :)
Then clean the solderpads with solder wick (or take some thick copper wire consisting of very fine single wires).
Finally solder in some irlml2502 (those are cheap on aliexpress).

As i am more used to Openpilot condiguration i ported Openpilot to this nice little board.
You can find some informations about that here:
http://www.rcgroups.com/forums/showthread.php?t=2456739

Regards,
Simon

User avatar
MrSatoV
Posts: 1
Joined: Fri Jul 17, 2015 4:05 am

Re: CJMCU microquad board

Post by MrSatoV »

Woah, Simon... damn. Must be nice to do stuff like that!

This $h!t just got real y'all! XD

Richard96816
Posts: 2
Joined: Sat Nov 21, 2015 10:49 pm

Re: CJMCU microquad board

Post by Richard96816 »

Great project! I received a couple boards a while back and am just now getting around to assembling them.

I have some receivers on the way. Trying to resist the temptation to rob one from another quad. Wondering if anyone has managed to connect an nRF24L01 module to the CJMCU as a receiver? I've got a few $3 modules I could use. And I have a Deviation modified Devo 7e transmitter with nRF24L01 module installed.

That would seem like the coolest way to outfit the CJMCU.

Also, the FETs on my boards say: "G2N4A" on them and not much else. Are these okay, or should I order replacements?

Also 2, has anyone gotten the compass chip to work usefully? Would mounting it on a one-inch or two-inch tall plastic standoff be sufficient to get it above the motor's magnetic fields?

Thanks.

Richard

goebish
Posts: 23
Joined: Mon Sep 16, 2013 12:01 pm

Re: CJMCU microquad board

Post by goebish »

I just added nrf24l01 support (only with WLToys V202 ptotocol for now), it should make its way into trunk soon.

https://github.com/cleanflight/cleanfli ... :crazepony

Note that on Rev1 board SPI1 connector is rotated 180° compared to the v2, not very convenient:
http://i.imgur.com/Y5G0eNk.jpg

Richard96816
Posts: 2
Joined: Sat Nov 21, 2015 10:49 pm

Re: CJMCU microquad board

Post by Richard96816 »

Very cool! Thanks.

User avatar
lot
Posts: 16
Joined: Mon Nov 18, 2013 7:36 pm

Re: CJMCU microquad board

Post by lot »

Hi all,
Just for telling you that we are developing a new board based on CJMJCU.
We recently published some details here:

http://aeracoop.net/en/cjmcu2-open-source-brushed-quadcopter/

We appreciate any suggestion.
Regards.

Post Reply