Naze32 hardware discussion thread
Re: Naze32 hardware discussion thread
Do you mean that then we will set for examp. 11deg 8min like 11,8 in cli?
Re: Naze32 hardware discussion thread
So then I think I should set 11deg 8min positive too 1108 in cli . anyone with knowledge on this wish to comment to help me out?
Last edited by QAV400 on Mon May 05, 2014 11:04 am, edited 1 time in total.
Re: Naze32 hardware discussion thread
scrat wrote:Do you mean that then we will set for examp. 11deg 8min like 11,8 in cli?
right, the capability is there i just havent bothered changing it.
its really not user friendly wiht fixdpoint
Re: Naze32 hardware discussion thread
in the meantime, can you add more examples and their values to the code/wiki ?
-1°2' => -102
10°18' => 1018
1°18' => 118
0°5' => 5
0°50' => 50
are those values even correct ?
might even be easier to add mag_dec_deg and mag_dec_sec
-1°2' => -102
10°18' => 1018
1°18' => 118
0°5' => 5
0°50' => 50
are those values even correct ?
might even be easier to add mag_dec_deg and mag_dec_sec
Re: Naze32 hardware discussion thread
Yes please more examples, the WIKI was vague on the subject
Re: Naze32 hardware discussion thread
larzac wrote:in the meantime, can you add more examples and their values to the code/wiki ?
-1°2' => -102
10°18' => 1018
1°18' => 118
0°5' => 5
0°50' => 50
are those values even correct ?
might even be easier to add mag_dec_deg and mag_dec_sec
THe thing to remember that there are 60 minutes in one degree- so you need to convert to decimal degrees. In above examples:
-1°2' = -1 degree + 2/60 = 1.03 -> -103
10°18' = 10 degrees + 18/60 = 10.3 -> 1030
1°18' = 1 degree + 18/60 = 1.3 -> 130
0°5' = 0 degrees + 5/60 = 0.08 -> 8
0°50' = 0 degrees + 50/60 = 0.83 -> 83
Re: Naze32 hardware discussion thread
Hi all,
First post here, so please be gentle.
I have an issue with my Rev 5 Naze32 FunFly Full version. It was working just as expected as shown by this quick video I took of my first flight with it. http://youtu.be/66xiJqJg-pI
Now, though, I believe its the Baseflight Chrome app, that may be the culprit, it locks up every time I am configuring the board. (havent been able to fly it now, because I cannot get all the setting checked and am not comfortable it not the board freezing). After about 4-5 minutes of being connected, with no apparent pattern of what clicks are causing it, the Baseflight app freezes, all tabs are pure white blank when I click through them, and I cannot get any response.
When this happens I leave the cord connected, click Disconnect in Baseflight, then Connect, and it will not connect again, just times out. UNTIL I unplug the cord, and reconnect from scratch. It loads all data, and 4 minutes later, again, blank white screens for each tab.
I am running Windows 8.0 laptop, latest Baseflight version, and updated the board through it to the latest online firmware version.
I connect it via usb, nothing other than essenatial items plugged in, (no bluetooth, no gps, no telemetry). Only receiver, and motors, same as in the video.
The date of the video will maybe give you an idea of the Baseflight release version, and firmware version (I am not sure, I didn't pay very close attention, I simply loaded what was released at that time).
* What could be the issue?
* Is a piece of hardware going (gone) bad?
* Could it be the software, I haven't tried multiple uninstalls and reinstalls of Baseflight yet.
Any advice is appreciated.
And tc, thanks for this hardware, I really enjoyed it while it was flying.
Ninja Edit: When/if I do add a GPS, how do I enter mag_declination of +10° 40' EAST (1004 ?)
First post here, so please be gentle.
I have an issue with my Rev 5 Naze32 FunFly Full version. It was working just as expected as shown by this quick video I took of my first flight with it. http://youtu.be/66xiJqJg-pI
Now, though, I believe its the Baseflight Chrome app, that may be the culprit, it locks up every time I am configuring the board. (havent been able to fly it now, because I cannot get all the setting checked and am not comfortable it not the board freezing). After about 4-5 minutes of being connected, with no apparent pattern of what clicks are causing it, the Baseflight app freezes, all tabs are pure white blank when I click through them, and I cannot get any response.
When this happens I leave the cord connected, click Disconnect in Baseflight, then Connect, and it will not connect again, just times out. UNTIL I unplug the cord, and reconnect from scratch. It loads all data, and 4 minutes later, again, blank white screens for each tab.
I am running Windows 8.0 laptop, latest Baseflight version, and updated the board through it to the latest online firmware version.
I connect it via usb, nothing other than essenatial items plugged in, (no bluetooth, no gps, no telemetry). Only receiver, and motors, same as in the video.
The date of the video will maybe give you an idea of the Baseflight release version, and firmware version (I am not sure, I didn't pay very close attention, I simply loaded what was released at that time).
* What could be the issue?
* Is a piece of hardware going (gone) bad?
* Could it be the software, I haven't tried multiple uninstalls and reinstalls of Baseflight yet.
Any advice is appreciated.
And tc, thanks for this hardware, I really enjoyed it while it was flying.
Ninja Edit: When/if I do add a GPS, how do I enter mag_declination of +10° 40' EAST (1004 ?)
Re: Naze32 hardware discussion thread
Official MW Java GUI for 2.3 works perfectly fine on basefligh/Naze32 ... did you try it ?
I find Chrome apps a bit odd for my taste ...
For some more advanced feature , as far as I know, you have to use CLI.
Mag declination is on official MW 2.3 Java GUI, and in CLI as well
I find Chrome apps a bit odd for my taste ...
For some more advanced feature , as far as I know, you have to use CLI.
Mag declination is on official MW 2.3 Java GUI, and in CLI as well
Re: Naze32 hardware discussion thread
+10° 40' EAST
10 + 40* (1/60) = 10.67
+10.7 is close enough.
10 + 40* (1/60) = 10.67
+10.7 is close enough.
Re: Naze32 hardware discussion thread
scrat wrote:Use this map: http://magnetic-declination.com/
And click on your exact location and see mag declination and set it in CLI.
With recent Baseflight Configurator updates, mag declination can be entered through the GUI... I think it's on the first page. Unfortunately, the format differs from the CLI input format.
Re: Naze32 hardware discussion thread
e_lm_70 wrote:Official MW Java GUI for 2.3 works perfectly fine on basefligh/Naze32 ... did you try it ?
I find Chrome apps a bit odd for my taste ...
I have been thinking it could be the Chrome app, and will try the Official MW Java GUI tonight when I get home.
It will be such a relief if the board isn't borked, and its just the app that was brain-farting. (I was gonna order another Naze32 anyway, but this would be better)
Re: Naze32 hardware discussion thread
PatrikE wrote:+10° 40' EAST
10 + 40* (1/60) = 10.67
+10.7 is close enough.
I don't have the Baseflight app right in front of me now, but, would I enter this on the first tab, in the Mag Declination box as you typed it (10.7)?
Re: Naze32 hardware discussion thread
e_lm_70 wrote:Official MW Java GUI for 2.3 works perfectly fine on basefligh/Naze32 ... did you try it ?
Is it the WinGUI from this page? http://code.google.com/p/mw-wingui/downloads/list
Re: Naze32 hardware discussion thread
No the java gui - https://code.google.com/p/multiwii/downloads/list the one thats inside multiwii release zips
Re: Naze32 hardware discussion thread
timecop wrote:No the java gui - https://code.google.com/p/multiwii/downloads/list the one thats inside multiwii release zips
Right.
I'm using what I believe is 2.3 release: MultiWii_2_3.zip .. inside you find the Java MW Gui both for Windows and Mac.
MultiWii_dev_2014_01_14__r1648.zip ... for me sound a beta or work in progress ... so I did not even bother to download it.
Personally I find way better the Java GUI then not the Crome App for Baseflight ... the luck of graphical representation of the quad, with pitch, roll and heading ... is a huge miss on the Crome App
Latest firmware with serious bug (Apr 30 2014 firmware)?
[...]
First problem: When testing the receiver signals in the GUI, the GUI locked down. Nothing but a power down of the Naze worked. But then it worked. Happened twice during congfiguration.
After all was configured (and yes, I reset all variables), I was going to fly a bit. Careful at first as the parameters might have changed their effect.
Was hovering for 20 sec, then wanted to move slightly left and the quad went right side up and it did not stop that rotation until it hit the ground.
I could not disarm. All props were spinning. The only way to stop them was disconnecting the battery.
[...]
Moved to the 32 bit software section under "NAZE32+latest baseflight frozes on PC and in the air"
Harald
First problem: When testing the receiver signals in the GUI, the GUI locked down. Nothing but a power down of the Naze worked. But then it worked. Happened twice during congfiguration.
After all was configured (and yes, I reset all variables), I was going to fly a bit. Careful at first as the parameters might have changed their effect.
Was hovering for 20 sec, then wanted to move slightly left and the quad went right side up and it did not stop that rotation until it hit the ground.
I could not disarm. All props were spinning. The only way to stop them was disconnecting the battery.
[...]
Moved to the 32 bit software section under "NAZE32+latest baseflight frozes on PC and in the air"
Harald
Last edited by hkubota on Tue May 06, 2014 9:16 am, edited 1 time in total.
Re: Naze32 hardware discussion thread
HFMan wrote:larzac wrote:in the meantime, can you add more examples and their values to the code/wiki ?
-1°2' => -102
10°18' => 1018
1°18' => 118
0°5' => 5
0°50' => 50
are those values even correct ?
might even be easier to add mag_dec_deg and mag_dec_sec
THe thing to remember that there are 60 minutes in one degree- so you need to convert to decimal degrees. In above examples:
-1°2' = -1 degree + 2/60 = 1.03 -> -103
10°18' = 10 degrees + 18/60 = 10.3 -> 1030
1°18' = 1 degree + 18/60 = 1.3 -> 130
0°5' = 0 degrees + 5/60 = 0.08 -> 8
0°50' = 0 degrees + 50/60 = 0.83 -> 83
I didn't know that for naze. I know for multiwii that you must convert values. Ok so what is for example 2deg and 9min = 2 degrees + 9/60 = 2.15 = 215?
Last edited by scrat on Tue May 06, 2014 9:17 am, edited 1 time in total.
Re: Naze32 hardware discussion thread
KC_703 wrote:scrat wrote:Use this map: http://magnetic-declination.com/
And click on your exact location and see mag declination and set it in CLI.
With recent Baseflight Configurator updates, mag declination can be entered through the GUI... I think it's on the first page. Unfortunately, the format differs from the CLI input format.
Yes. In CLI you can put right value for example: 209 but when using first page in conf, you can set just 2 = 200. so it is not ok.
Re: Naze32 hardware discussion thread
2.09 or 2 ... it could be to a rounding in the GUI ... also 2.09 or 2.00 will not change a bit for the RTH and PH
Re: Naze32 hardware discussion thread
I'm using baseflight conf.
- seibernator
- Posts: 7
- Joined: Sun Apr 29, 2012 11:38 pm
Re: Naze32 hardware discussion thread
Hello all
I have a little problem with my build I hope one of you can help me with. I am basically trying to get telemetry to work so that I can get the voltage reading from my Mini H quad to my little Flytron LCD screen I plug into the back of my Frsky TX.
The reading for the voltage supplied to the receiver and the RSSI readings are coming through OK but not the voltage of the lipo on the quad. As you can see in the picture below I already have a supply from the battery already connected to the battery voltage monitor pin on the Naze32 and I can see the voltage reading correctly in Baseflight Configurator so I know that it is working.
I also already have VBAT and TELEMETRY enabled on the little FC board as well. There aren't very many tips out there that show you how you should connect your Frsky D4R-II receiver to the Naze32 but I assumed you would somehow use the already assigned Frsky telemetry port on the Naze board.
I am confused which ports I should use, should it be the telemetry pins in the middle of the board or the Frsky telemetry pins next to the buzzer pins? I have tried both and nothing seems to work.
What wires should I use out of the Frsky receiver to connect to the Naze and where should they go? Am I missing something here?
Thanks for any help, especially from anyone out there that has got this working. I have been through the search function on this forum and I am seeing conflicting information. I am just running the bog-standard version 2.3 firmware on the Naze.
I have a little problem with my build I hope one of you can help me with. I am basically trying to get telemetry to work so that I can get the voltage reading from my Mini H quad to my little Flytron LCD screen I plug into the back of my Frsky TX.
The reading for the voltage supplied to the receiver and the RSSI readings are coming through OK but not the voltage of the lipo on the quad. As you can see in the picture below I already have a supply from the battery already connected to the battery voltage monitor pin on the Naze32 and I can see the voltage reading correctly in Baseflight Configurator so I know that it is working.
I also already have VBAT and TELEMETRY enabled on the little FC board as well. There aren't very many tips out there that show you how you should connect your Frsky D4R-II receiver to the Naze32 but I assumed you would somehow use the already assigned Frsky telemetry port on the Naze board.
I am confused which ports I should use, should it be the telemetry pins in the middle of the board or the Frsky telemetry pins next to the buzzer pins? I have tried both and nothing seems to work.
What wires should I use out of the Frsky receiver to connect to the Naze and where should they go? Am I missing something here?
Thanks for any help, especially from anyone out there that has got this working. I have been through the search function on this forum and I am seeing conflicting information. I am just running the bog-standard version 2.3 firmware on the Naze.
Re: Naze32 hardware discussion thread
You need to ARM and wait a few seconds >= 5 before all the data on frsky LCD is updated. Battery telemetry is not transmitted every cycle.
- seibernator
- Posts: 7
- Joined: Sun Apr 29, 2012 11:38 pm
Re: Naze32 hardware discussion thread
Thanks, I will try that again. Could you please confirm for me how the receiver should be hooked up to the Naze board?
I am using the green RX lead from the receiver to connect up to the telemetry TX pin in the middle of the board. The black ground lead is attached to any ground pin on the board.
I have enabled VBAT and TELEMETRY within the CLI. Is there anything else I need to do?
Nothing seems to come through even when the board is armed for more than 5 seconds. Has anyone else got this working properly for Frsky? Thanks.
I am using the green RX lead from the receiver to connect up to the telemetry TX pin in the middle of the board. The black ground lead is attached to any ground pin on the board.
I have enabled VBAT and TELEMETRY within the CLI. Is there anything else I need to do?
Nothing seems to come through even when the board is armed for more than 5 seconds. Has anyone else got this working properly for Frsky? Thanks.
Re: Naze32 hardware discussion thread
It connects to frsky telemetry pin in the corner near usb.
Re: Naze32 hardware discussion thread
timecop wrote:No the java gui - https://code.google.com/p/multiwii/downloads/list the one thats inside multiwii release zips
OK, Thanks timecop. I got the GUI from the page you linked. Interesting the 64 bit version will not launch on my system (I do run Win7 64 bit) but I was able to run the 32 bit version of the GUI.
Now the waiting game, getting home again tonight to plug in and test the Naze32 again.
I'm seeing other people, suggesting its not a one-off situation, saying that their boards are locking up as well, and mentioning a previous version of the firmware does not.
(I did find a way to get a previous revision of the hex and will try restoring the board to functioning without locking up)
Last edited by Naze_Moto on Tue May 06, 2014 10:04 pm, edited 1 time in total.
- seibernator
- Posts: 7
- Joined: Sun Apr 29, 2012 11:38 pm
Re: Naze32 hardware discussion thread
Thanks
I have tried exactly as you have recommended but it still does not appear to work properly. Here are a list of the settings from a dump of the config that are related to serial port or telemetry configuration. Are any of them incorrect? Am I missing out any other commands?
feature PPM
feature VBAT
feature MOTOR_STOP
feature SOFTSERIAL
feature TELEMETRY
set serial_baudrate = 115200
set softserial_baudrate = 9600
set softserial_inverted = 1
set serialrx_type = 0
set telemetry_softserial = 1
set telemetry_switch = 1
Here is a photo of how I have wired it up and you can see on the Flytron screen the Frsky telemetry coming through but the smaller set of numbers which represent the battery voltage are wrong. If none of the wires from the Frsky RX are connected to the Naze the same numbers come through so I don't think anything is coming through from the FC board.
Really appreciate any help here, thanks.
I have tried exactly as you have recommended but it still does not appear to work properly. Here are a list of the settings from a dump of the config that are related to serial port or telemetry configuration. Are any of them incorrect? Am I missing out any other commands?
feature PPM
feature VBAT
feature MOTOR_STOP
feature SOFTSERIAL
feature TELEMETRY
set serial_baudrate = 115200
set softserial_baudrate = 9600
set softserial_inverted = 1
set serialrx_type = 0
set telemetry_softserial = 1
set telemetry_switch = 1
Here is a photo of how I have wired it up and you can see on the Flytron screen the Frsky telemetry coming through but the smaller set of numbers which represent the battery voltage are wrong. If none of the wires from the Frsky RX are connected to the Naze the same numbers come through so I don't think anything is coming through from the FC board.
Really appreciate any help here, thanks.
Re: Naze32 hardware discussion thread
Quick question - are older versions of the firmware available anywhere? My Tricopter is rolling right pretty hard after the last flash and no amount of accelerometer roll trim via stick or GUI seems to affect the roll. Was wanting to flash back to the version prior to the one dated 4.30.14 but I can't seem to find it. Think I'll start downloading them and flashing them from a local file going forward.
Anyway, if someone can point me in the right direction I'd appreciate it.
Thanks!
Anyway, if someone can point me in the right direction I'd appreciate it.
Thanks!
Re: Naze32 hardware discussion thread
ronin4740 wrote:Quick question - are older versions of the firmware available anywhere?
This is what another member here confirmed for me, I don't want to step on any toes since tc said there is no way to get a previous version.
Go here:
https://github.com/multiwii/baseflight/ ... flight.hex
Click on History > Find the date you want > Click on Browse Code (right side) > Click Raw > Select All > Copy to text editor > Save file locally with .hex extension.
I have already done this with the file I want, and will try to manually flash it tonight.
Re: Naze32 hardware discussion thread
Naze_Moto wrote:
This is what another member here confirmed for me, I don't want to step on any toes since tc said there is no way to get a previous version.
Go here:
https://github.com/multiwii/baseflight/ ... flight.hex
Click on History > Find the date you want > Click on Browse Code (right side) > Click Raw > Select All > Copy to text editor > Save file locally with .hex extension.
I have already done this with the file I want, and will try to manually flash it tonight.
Thanks. I see where the history button is now - that's what I failed to find on my own. With that knowledge I was able to get the second most recent firmware downloaded and will test with it. It's also possible all the crashes and hard landings have borked my FC. Being able to go back to firmware that worked properly for me in attitude and horizon modes will help me troubleshoot.
*edit*
I flashed the firmware and that didn't fix the problem. Starting to think that one of the crashes has killed the accelerometer. I was looking at the raw data graphs, comparing the gyro and accelerometer graphs to one another. If I'm lifting the tail quickly shouldn't I see the same color line move on both graphs?
Re: Naze32 hardware discussion thread
ronin4740 wrote: I was able to get the second most recent firmware downloaded and will test with it. It's also possible all the crashes and hard landings have borked my FC. Being able to go back to firmware that worked properly for me in attitude and horizon modes will help me troubleshoot.
I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur. I am going to be doing that tonight, myself. Testing to see which revision of the hex the problems do/don't exist.
...Not sure about the graphs...
Re: Naze32 hardware discussion thread
Naze_Moto wrote:ronin4740 wrote: I was able to get the second most recent firmware downloaded and will test with it. It's also possible all the crashes and hard landings have borked my FC. Being able to go back to firmware that worked properly for me in attitude and horizon modes will help me troubleshoot.
I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur. I am going to be doing that tonight, myself. Testing to see which revision of the hex the problems do/don't exist.
...Not sure about the graphs...
Thanks for the advice. I'll try a few of the firmwares from April 5 and prior and see if it fixes my issue.
Re: Naze32 hardware discussion thread
Naze_Moto wrote:I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur.
Where did you see other people state the same issues? You joined this forum one day ago, and start spreading this kind of chatter? For the record, I've not had any connectivity issues with any Baseflight or Baseflight Configurator in recent releases, nor have I seen anybody else report it in this forum.
Re: Naze32 hardware discussion thread
HFMan wrote:Naze_Moto wrote:I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur.
Where did you see other people state the same issues? You joined this forum one day ago, and start spreading this kind of chatter? For the record, I've not had any connectivity issues with any Baseflight or Baseflight Configurator in recent releases, nor have I seen anybody else report it in this forum.
Um, you're slightly less a newborn than I am. "Joined" but have been reading a long time, before creating account. (typical internet assumptions... )
I have read in this thread viewtopic.php?f=23&t=4970 specifically, the same behavior of either the app, or the board locking up.
Citing the date that the behavior changed from nice operation to freezing up for some unknown reason.
I was simply offering suggestions on what to try, to get the board back to functioning again.
BTW, I flashed the full Naze32 tonight with the hex from Feb 20, and have not seen a lockup yet, but has only been a few hours. When previously the board/software (?) would freeze within 4 minutes of the connection.
Re: Naze32 hardware discussion thread
ronin4740 wrote:Quick question - are older versions of the firmware available anywhere? My Tricopter is rolling right pretty hard after the last flash and no amount of accelerometer roll trim via stick or GUI seems to affect the roll. Was wanting to flash back to the version prior to the one dated 4.30.14 but I can't seem to find it. Think I'll start downloading them and flashing them from a local file going forward.
Anyway, if someone can point me in the right direction I'd appreciate it.
Thanks!
Here you go with version prior to 30.4.2014 - https://dl.dropboxusercontent.com/u/125 ... 042014.hex
Re: Naze32 hardware discussion thread
seibernator wrote:Thanks
I have tried exactly as you have recommended but it still does not appear to work properly. Here are a list of the settings from a dump of the config that are related to serial port or telemetry configuration. Are any of them incorrect? Am I missing out any other commands?
feature PPM
feature VBAT
feature MOTOR_STOP
feature SOFTSERIAL
feature TELEMETRY
set serial_baudrate = 115200
set softserial_baudrate = 9600
set softserial_inverted = 1
set serialrx_type = 0
set telemetry_softserial = 1
set telemetry_switch = 1
Here is a photo of how I have wired it up and you can see on the Flytron screen the Frsky telemetry coming through but the smaller set of numbers which represent the battery voltage are wrong. If none of the wires from the Frsky RX are connected to the Naze the same numbers come through so I don't think anything is coming through from the FC board.
Really appreciate any help here, thanks.
I think you have Rx connected wrong...firt row is channel 1 to 4 and second row is from 5 to 8.
Re: Naze32 hardware discussion thread
Naze_Moto wrote:HFMan wrote:Naze_Moto wrote:I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur.
Where did you see other people state the same issues? You joined this forum one day ago, and start spreading this kind of chatter? For the record, I've not had any connectivity issues with any Baseflight or Baseflight Configurator in recent releases, nor have I seen anybody else report it in this forum.
Um, you're slightly less a newborn than I am. "Joined" but have been reading a long time, before creating account. (typical internet assumptions... )
I have read in this thread viewtopic.php?f=23&t=4970 specifically, the same behavior of either the app, or the board locking up.
Citing the date that the behavior changed from nice operation to freezing up for some unknown reason.
I was simply offering suggestions on what to try, to get the board back to functioning again.
BTW, I flashed the full Naze32 tonight with the hex from Feb 20, and have not seen a lockup yet, but has only been a few hours. When previously the board/software (?) would freeze within 4 minutes of the connection.
What revision of Naze32 do you have? I have rev5 - purple and have no lock-up in baseflight configurator or in the air.
Re: Naze32 hardware discussion thread
scrat wrote:What revision of Naze32 do you have? I have rev5 - purple and have no lock-up in baseflight configurator or in the air.
I have the Rev 5, Red version. The software locked up, or the board did.
I experienced this with the Chrome App Baseflight Configurator, with the WINGUI app, and with the Official MW GUI 2.3. Using all of them, after a few minutes, either the software or board would freeze.
I don't know if it freezes in the air, I never trusted it to fly it again, until I got the freezing sorted.
Last night, I flashed to a late February hex, and didn't see any freezing yet. I will continue to bench test it, until I'm satisfied it won't freeze again.
Re: Naze32 hardware discussion thread
Please post your whole CLI and when status please. I would like to see what you have set.
Re: Naze32 hardware discussion thread
My board is working and I have no freezing when connected to my pc, using Baseflight configurator, or official mw gui 2.3, now.
Although I am sure I can reproduce the freezing situation, so, in which scenario would you like to see my settings?
Actually, thinking about it, it would be the same CLI settings, no matter what. I haven't set anything different, between the freezing and non-freezing scenarios.
Only thing that changed is the hex file I flashed.
Although I am sure I can reproduce the freezing situation, so, in which scenario would you like to see my settings?
Actually, thinking about it, it would be the same CLI settings, no matter what. I haven't set anything different, between the freezing and non-freezing scenarios.
Only thing that changed is the hex file I flashed.
Re: Naze32 hardware discussion thread
I would like to see your CLI settings with BF firmware when your board freezes.
Re: Naze32 hardware discussion thread
Naze_Moto wrote:My board is working and I have no freezing when connected to my pc, using Baseflight configurator, or official mw gui 2.3, now.
Although I am sure I can reproduce the freezing situation, so, in which scenario would you like to see my settings?
Actually, thinking about it, it would be the same CLI settings, no matter what. I haven't set anything different, between the freezing and non-freezing scenarios.
Only thing that changed is the hex file I flashed.
that's not actually possible as eeprom version would have likely changed and unless you did 'defaults' after each reflash teh results are invalid
-
- Posts: 2
- Joined: Thu May 08, 2014 7:01 pm
Re: Naze32 hardware discussion thread
hi guys,
i have a question...
I have the naze acro fc and frsky tfr6 and futaba t8fg transmitter.
As per the naze acro fc if my rx is standard, i can use the breakout cable to connect the fc and the rx....
Can you please tell me if i have to use the breakout cable for the frsky tfr6 or is there an alternative method/wire?
i have a question...
I have the naze acro fc and frsky tfr6 and futaba t8fg transmitter.
As per the naze acro fc if my rx is standard, i can use the breakout cable to connect the fc and the rx....
Can you please tell me if i have to use the breakout cable for the frsky tfr6 or is there an alternative method/wire?
Re: Naze32 hardware discussion thread
The TFR6 does not use PPM, so you will need to use the breakout cable.
-
- Posts: 2
- Joined: Thu May 08, 2014 7:01 pm
Re: Naze32 hardware discussion thread
if the breakout cable is not available locally, can i use female to female cables?
-
- Posts: 48
- Joined: Sat Jun 22, 2013 2:37 am
Re: Naze32 hardware discussion thread
timecop, I noticed on your latest boards you didn't put a cap on the regulator bypass pin. The SPX3819 datasheet (nice find BTW!) has a chart that shows ~60uV ripple with a 10nF bypass cap, and ~300uV without. Even 300uV seems small, but if I added a bypass cap would I potentially improve performance of my sensors, cause problems with slower startup, or simply be wasting my time and capacitors?
I have 10nF X7R caps in my bin, but I figured I should ask you before I brick my new board.
Kev
I have 10nF X7R caps in my bin, but I figured I should ask you before I brick my new board.
Kev
Re: Naze32 hardware discussion thread
It wasn't there because it's not "required" by RT9193 which was the previous reg. SPX3819 move was due to people wanting to run directly off lipo, and I didn't want to do a pcb redo. Yes, you can add the cap and it will probably improve things.
-
- Posts: 48
- Joined: Sat Jun 22, 2013 2:37 am
Re: Naze32 hardware discussion thread
Thanks tc, yeah I am not really worried about future boards having the cap. I'm used to adding a little extra bling to my aircraft anyways.
I have to add that I'm very impressed how small you made NazeMini... it's even smaller than minimOSD! You could integrate minimOSD hardware on it and it would still probably be smaller than it's big brother.
Kev
I have to add that I'm very impressed how small you made NazeMini... it's even smaller than minimOSD! You could integrate minimOSD hardware on it and it would still probably be smaller than it's big brother.
Kev
Re: Naze32 hardware discussion thread
Planning to use a Futaba RX on my next quad with Naze 32 - does it matter if the RX is in HS mode?
Or should I use normal mode instead?
Or should I use normal mode instead?
Help!?
Hi guys. I have this one acronaze32 which only have the blue led lights up when powered.
It worked until i flashed it with latest firmware while forgetting to unplug the lipo from my quad. The flashing process started just fine, then i remember the lipo as the motors making some beeping sound and disconnect the battery. The process ended with stm32 timeout. and i no longer can connect to baseflight conf and only the blue led lights up once the board gets power. No initialization sequence.
What could be wrong? Can it be recover?
http://www.youtube.com/watch?v=cRE83-tmN-U
It worked until i flashed it with latest firmware while forgetting to unplug the lipo from my quad. The flashing process started just fine, then i remember the lipo as the motors making some beeping sound and disconnect the battery. The process ended with stm32 timeout. and i no longer can connect to baseflight conf and only the blue led lights up once the board gets power. No initialization sequence.
What could be wrong? Can it be recover?
http://www.youtube.com/watch?v=cRE83-tmN-U