Tricopter 2.5 issues
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Tricopter 2.5 issues
Hi guys,
I posted this on rcgroups but I thought you may be able to help, I've got some issues with my tricopter I'm trying to sort out, mostly related to uneven RPM on the motors, as you can see from the video one motor RPM is showing constantly higher in the GUI even when the tricopter is completely level in pitch/roll. Thus I cant take off level let alone hover I also have the issue of the motors not all starting correctly at the same point for a given throttle position but I think thats a different issue.
Do you have any suggestions what might be causing this? Any help would be appreciated.
Thanks in advance.
http://www.youtube.com/watch?v=OzhMA79z ... e=youtu.be
I posted this on rcgroups but I thought you may be able to help, I've got some issues with my tricopter I'm trying to sort out, mostly related to uneven RPM on the motors, as you can see from the video one motor RPM is showing constantly higher in the GUI even when the tricopter is completely level in pitch/roll. Thus I cant take off level let alone hover I also have the issue of the motors not all starting correctly at the same point for a given throttle position but I think thats a different issue.
Do you have any suggestions what might be causing this? Any help would be appreciated.
Thanks in advance.
http://www.youtube.com/watch?v=OzhMA79z ... e=youtu.be
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Re: Tricopter 2.5 issues
Forgot to mention I am using the CRIUS aio board
Re: Tricopter 2.5 issues
trim and subtrim to zero?
Re: Tricopter 2.5 issues
think It's normal, you have to trim it out, first calibrate acc, mag and esc then folow this:
http://www.multiwii.com/software
http://ncopters.blogspot.de/2012/04/how ... on-in.html
viewtopic.php?f=18&t=1752&p=22493&hilit=trim#p22493
http://www.multiwii.com/software
http://ncopters.blogspot.de/2012/04/how ... on-in.html
viewtopic.php?f=18&t=1752&p=22493&hilit=trim#p22493
Re: Tricopter 2.5 issues
i agree, on the gui, you can see that your roll is 1471, that will cause your bird to try to roll that direction immediately. trim your TX to 1500 on roll and you should be fine.
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Re: Tricopter 2.5 issues
Thanks, that's what it was. Also a TRAP for n00bs like myself is that multiwii default mode is acro. lol.
Re: Tricopter 2.5 issues
been there done that
Re: Tricopter 2.5 issues
you have to start with acro, level mode isnt always calibrated properly initially and can make it hard to identify other issues, like vibrations until you disable level mode.
I rarely use level mode unless i am trying to get my copter to hover perfectly still (as still as my cheap sensors can hold it)
I rarely use level mode unless i am trying to get my copter to hover perfectly still (as still as my cheap sensors can hold it)
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Re: Tricopter 2.5 issues
Does anyone know any tricks to getting altitude hold to work with the crius aio pro? I enabled baro mode on aux3 but when I enable it nothing happens, does not attempt to maintain height?
-
- Posts: 506
- Joined: Thu May 05, 2011 8:13 am
- Location: Slovenia
Re: Tricopter 2.5 issues
fpv_downunder wrote:Does anyone know any tricks to getting altitude hold to work with the crius aio pro? I enabled baro mode on aux3 but when I enable it nothing happens, does not attempt to maintain height?
Since you are running official release 2.1 it is possible that you will never get satisfactory ALT. HOLD because biggest improvements were done after that release.
Regards
Andrej
Re: Tricopter 2.5 issues
also, if you are enabled baro before you have gotten at least 3 feet in the air you wont get good results. turn baro on once youve reached the height you want to hold.
-
- Posts: 23
- Joined: Tue Jan 08, 2013 10:05 am
Re: Tricopter 2.5 issues
Oh thanks for that, I'll try one of the dev releases then I guess...