motor turns slowly
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
motor turns slowly
hi, I'm new
I make a quadcopter "quadx"
I use
1100 kv motor
25 A esc
multiwii SE v2.5
3s 2200 mah battery
but the motors does not turn fast enough and not flying quadcopter.
please help me
I make a quadcopter "quadx"
I use
1100 kv motor
25 A esc
multiwii SE v2.5
3s 2200 mah battery
but the motors does not turn fast enough and not flying quadcopter.
please help me
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
yes I'm activate the define ESC_CALIB_CANNOT_FLY
Re: motor turns slowly
You could try to calibrate them by plugging directly into the RX CH3.
RX off
TX on
Throttle full
Plug RX in to power
ESC beeps
Pull Throttle to idle
ESC beeps again
done.
RX off
TX on
Throttle full
Plug RX in to power
ESC beeps
Pull Throttle to idle
ESC beeps again
done.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
when I connect esc direct rx ch3 motors turn very fastly
Re: motor turns slowly
Re-calibrate all the ESCs directly from the RX throttle channel.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
waltr wrote:Re-calibrate all the ESCs directly from the RX throttle channel.
How do I make it ?
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
DOES NOT fly Vibrates more
Re: motor turns slowly
This sounds more like a Bad solder joint between ESC and Motor or a broken wire inside the motor.
OR- very badly out of balance motors or props or both.
OR- very badly out of balance motors or props or both.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
waltr wrote:This sounds more like a Bad solder joint between ESC and Motor or a broken wire inside the motor.
OR- very badly out of balance motors or props or both.
when throttle %50 and right stick pull right or left, flipped my quadcopter (left or right motors turns normally)
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
Is there anyone who can help ?
Re: motor turns slowly
We need more information. What is the problem?
Screen shot of GUI and config.h might help.
Screen shot of GUI and config.h might help.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
my config.h
- Attachments
-
- config.rar
- my config file
- (18.96 KiB) Downloaded 181 times
Re: motor turns slowly
Very hard to tell but it looks like the props are on the wrong motor and/or the motors are all turning the wrong way.
Is Green props the front and red the back. If so then recheck the MW Wiki and tutorials plus the beginnre's thread.
Show us a screen shot of Multiwiiconfig.exe with the RX/TX on and the sticks centered to see the center values.
If a video of MWconfig.exe then show the stick end point values.
Is Green props the front and red the back. If so then recheck the MW Wiki and tutorials plus the beginnre's thread.
Show us a screen shot of Multiwiiconfig.exe with the RX/TX on and the sticks centered to see the center values.
If a video of MWconfig.exe then show the stick end point values.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
waltr wrote:Very hard to tell but it looks like the props are on the wrong motor and/or the motors are all turning the wrong way.
Is Green props the front and red the back. If so then recheck the MW Wiki and tutorials plus the beginnre's thread.
Show us a screen shot of Multiwiiconfig.exe with the RX/TX on and the sticks centered to see the center values.
If a video of MWconfig.exe then show the stick end point values.
Pictures of my motor rotation is as follows. And all propellers blows down.
-
- Posts: 12
- Joined: Mon Sep 22, 2014 3:32 pm
Re: motor turns slowly
the problem was solved
I had to replace the whole propellers.
I had to replace the whole propellers.
Re: motor turns slowly
Where the propellers slipping in the hubs?