Turnigy 9x Transmitter Switch setup
- NikTheGreek
- Posts: 348
- Joined: Thu Dec 08, 2011 4:17 pm
- Location: Greece
- Contact:
Turnigy 9x Transmitter Switch setup
Hi.
I got a Turnigy 9X transmitter and i'm trying to setup all the switches that my Bicopter need to fly.
I've searched a lot in the web with no luck.
Can someone please help me ?
Thank you in advance.
I got a Turnigy 9X transmitter and i'm trying to setup all the switches that my Bicopter need to fly.
I've searched a lot in the web with no luck.
Can someone please help me ?
Thank you in advance.
Re: Turnigy 9x Transmitter Switch setup
You can take a look at my EEprom.
/Patrik
/Patrik
- Attachments
-
- EEprom.rar
- (1.36 KiB) Downloaded 312 times
- NikTheGreek
- Posts: 348
- Joined: Thu Dec 08, 2011 4:17 pm
- Location: Greece
- Contact:
Re: Turnigy 9x Transmitter Switch setup
Thnx PatrikE....but..what kind of file is this ??
I cant read it
I cant read it
Re: Turnigy 9x Transmitter Switch setup
I have Flashed my TGY and it's the file with the settings.
But if you haven't flashed your radio you can't use the file.
Here's the software simulator to read the file.
http://code.google.com/p/er9x/
But if you haven't flashed your radio you can't use the file.
Here's the software simulator to read the file.
http://code.google.com/p/er9x/
- NikTheGreek
- Posts: 348
- Joined: Thu Dec 08, 2011 4:17 pm
- Location: Greece
- Contact:
Re: Turnigy 9x Transmitter Switch setup
Thank you patrik ..but all this sounds like Greek to me .
Maybe in a future life i ll be able to understand .
Thank you anyway
Maybe in a future life i ll be able to understand .
Thank you anyway
Re: Turnigy 9x Transmitter Switch setup
Patrik is right! For a few dollars on hardware and some little soldering you will have a fully computer configurable transmitter . You don't have to understand everything to get things to work. The stock software sucks ,you can't assign the knobs and pots to your functions.
Hans
Hans
Re: Turnigy 9x Transmitter Switch setup
Partially OK - you also need to install a new firmware to get the best out of the radio
read more here:
http://www.undcon.com/?s=9X
//UndCon
read more here:
http://www.undcon.com/?s=9X
//UndCon
- NikTheGreek
- Posts: 348
- Joined: Thu Dec 08, 2011 4:17 pm
- Location: Greece
- Contact:
Re: Turnigy 9x Transmitter Switch setup
ok ok..
you convinced me..
i'll do it but later.
for now i have bigger things to solve
you convinced me..
i'll do it but later.
for now i have bigger things to solve
Re: Turnigy 9x Transmitter Switch setup
Hi PatrikE,
Do you know how to setup "binary" encoded switches in ER9X?
regards,
ziss_dm
Do you know how to setup "binary" encoded switches in ER9X?
regards,
ziss_dm
Re: Turnigy 9x Transmitter Switch setup
If you mean a 1000 - 2000 swicth when you say binary it should be setup like this.
In this case i use ThrottleCut swich to trigg the shutter on the camera.
In this case i use ThrottleCut swich to trigg the shutter on the camera.
Re: Turnigy 9x Transmitter Switch setup
does the eeprom posted earlier does it have the switch configuration for mode selection? can't figure out how to configure it on er9x
Re: Turnigy 9x Transmitter Switch setup
The modeswitch is programmed for
LOW|MID|HIGH On AUX2
D/R and expo is also programmed on this switch.
Check Expo/DR tab in editor
Default settings is 0,100,100,0
LOW|MID|HIGH On AUX2
D/R and expo is also programmed on this switch.
Check Expo/DR tab in editor
Default settings is 0,100,100,0
Re: Turnigy 9x Transmitter Switch setup
PatrikE wrote:The modeswitch is programmed for
LOW|MID|HIGH On AUX2
D/R and expo is also programmed on this switch.
Check Expo/DR tab in editor
Default settings is 0,100,100,0
I should have checked before asking, I saw your mix setup on ch6 I'm bit new to expo so not sure I know what all those mean
Re: Turnigy 9x Transmitter Switch setup
Expo creates a span where the output from the stick is smaller around neutral.
The curve is eponential.
The curve is eponential.
- Attachments
-
- Expo.png
- (4.3 KiB) Not downloaded yet
- NikTheGreek
- Posts: 348
- Joined: Thu Dec 08, 2011 4:17 pm
- Location: Greece
- Contact:
Re: Turnigy 9x Transmitter Switch setup
Done it !!!!
Patrick just a noobish question for you
Do i have to "Write Memory to TX" with your file ???
Thnx in advance.
Patrick just a noobish question for you
Do i have to "Write Memory to TX" with your file ???
Thnx in advance.
Re: Turnigy 9x Transmitter Switch setup
NikTheGreek wrote:Do i have to "Write Memory to TX" with your file ???
"Write EEPROM to TX" means you load the settings to the TX.
So If you want to use them... YES!...
Remember to calibrate the sticks after you loaded My settings to YOUR TX.
All radios have slightly different values on the Potentiometers.
/Patrik