The config looks correct.
Can you Test the I2C gps on a V2.3 version? ex the FW Nav from April -14
https://multiwii.googlecode.com/svn/bra ... 140402.zip
Just to rule out the new MWii version and the I2C.
Search found 1976 matches
- Fri Jul 10, 2015 9:47 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
- Thu Jul 09, 2015 6:51 pm
- Forum: Shields, boards and sensors
- Topic: Did I brick my Bluetooth?
- Replies: 1
- Views: 1354
Re: Did I brick my Bluetooth?
Maybe it have reset to factory default.
Test to connect it direct on a FTDI.
You should get answer from it if you change to correct Baudrate.
Test to connect it direct on a FTDI.
You should get answer from it if you change to correct Baudrate.
- Wed Jul 08, 2015 9:51 am
- Forum: Software
- Topic: Cleanflight aka Multiwii port to STM32 F10x and F30x
- Replies: 761
- Views: 1583282
Re: Cleanflight aka Multiwii port to STM32 F10x and F30x
Cleanflight don't have Gps functions for Fixedwing.
Only for visual functions on OSD.
Only for visual functions on OSD.
- Wed Jul 08, 2015 9:47 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Ok problem isolation.
Check the settings in I2C_GPS config.
Baudrate etc.
Check the settings in I2C_GPS config.
Baudrate etc.
- Tue Jul 07, 2015 8:11 pm
- Forum: Software
- Topic: Airplane RTH BaseFlight
- Replies: 143
- Views: 138456
Re: Airplane RTH BaseFlight
The Fixed wing RTH is integrated in Baseflight official now.
It does RTH and Pos hold.
I have a unofficial version with the Cruise mode too.
BF Dev version
I'm not sure if Baseflight can run on a CC3D board.
I have started a Guide for Baseflight setup to.
http://fotoflygarn.blogspot.se/2015/01/ ... dwing.html
It does RTH and Pos hold.
I have a unofficial version with the Cruise mode too.
BF Dev version
I'm not sure if Baseflight can run on a CC3D board.
I have started a Guide for Baseflight setup to.
http://fotoflygarn.blogspot.se/2015/01/ ... dwing.html
- Mon Jul 06, 2015 10:13 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
That sounds strange!.. " The GPSHOME box switches on and off " It indicates there's something wrong with the FIX. ( >= 5 sat ) At climbout the Motor should be at Max until hold altitude is reached. In all other GPS situations it should hold Cruise throttle and increase/decrease slowly depe...
- Wed Jul 01, 2015 11:02 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Try to enable RTH When you lauch.
It will climb out and start cirkling over your head intill you take over.
It will climb out and start cirkling over your head intill you take over.
- Tue Jun 30, 2015 2:29 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
I2C is practical if you want to connect a OSD.
But use my patched version.
You can fond the Cruise code in gps.c.
Search for GEO
But use my patched version.
You can fond the Cruise code in gps.c.
Search for GEO
- Sun Jun 28, 2015 12:45 pm
- Forum: General discussions
- Topic: Various Arduino Modules - Can I use them w/ Multiwii?
- Replies: 1
- Views: 1278
Re: Various Arduino Modules - Can I use them w/ Multiwii?
Only module #5 can.be used.
- Thu Jun 25, 2015 8:02 pm
- Forum: Software development
- Topic: How to get the data sending out through the serial?
- Replies: 4
- Views: 2284
- Thu Jun 25, 2015 7:59 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Serial
- Replies: 1
- Views: 827
Re: Serial
How about this checkbox in Gui settings tab?
- Wed Jun 24, 2015 8:16 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
I had many many problems yesterday with sync of the PPM stream. Sometimes all the channels got blocked or their values were changing. When I went to disarm some servos went to weird positions and the motor went to 45% power !!!. Bad things. This was happening until I modified the limits of the chan...
- Tue Jun 23, 2015 1:46 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Ok, I will test with 8ch for now. In config.h like this ? /********************************************************************/ /**** RSSI ****/ /********************************************************************/ //#define RX_RSSI //#define RX_RSSI_PIN A3 #define RX_RSSI_CHAN 8 //RSSI injection...
- Tue Jun 23, 2015 11:43 am
- Forum: Boards
- Topic: Atmega 328P on Super X 125mm
- Replies: 9
- Views: 6928
Re: Atmega 328P on Super X 125mm
Weeeelcome to the dark side brm...
- Tue Jun 23, 2015 9:03 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Sounds like a good setup. The 3Way sw i usually set. PassThru|Acro|Horizon . If you have a second 3Way you can set GPSHOLD and RTH on it. But separate switches works fine if you have channels for it. You can inject RSSI as channel 8 or 9 to mwii. But increase from the synctime to >= 27µs to avoid th...
- Mon Jun 22, 2015 2:28 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Passthrough Uses no sensors only the input from TX. You get a small delay on the controls and FC is just doing the mixing based on TX. In the current mixtable it's not possible. You will have to modify it for separate inputs. One thing to take in consideration is The Pid's only have one output/Axis....
- Sun Jun 21, 2015 10:13 am
- Forum: Connecting elements
- Topic: in "Flight Config UI" flight Yaw constantly changing.
- Replies: 2
- Views: 1755
Re: in "Flight Config UI" flight Yaw constantly changing.
Hi. The acc fluctuation is normal. You can enable some Low Pass Filter to get a cleaner output from the ACC. ex. #define GYRO_LPF_98HZ or lower // 256 is default if nothing is enabled. Yaw is drifting because I-term is building up when it's stationary. It will correct itself when flying. So add some...
- Fri Jun 19, 2015 9:57 pm
- Forum: Software development
- Topic: Adding and/or refactoring V-Tail, HEX6H, OCTO8H support
- Replies: 5
- Views: 2326
Re: Adding and/or refactoring V-Tail, HEX6H, OCTO8H support
Hi and welcome. It's quite easy to modify a Mixer for motors. First element is Roll second is Nick Third is Yaw. motor[0] = PIDMIX(+Roll ,-Nick ,+Yaw); //MIDFRONT_L The easiest is to use OCTOFLATX and modify. Since all motors in in parallel line the Roll input need to be 1 for all motors. + on left ...
- Fri Jun 19, 2015 9:32 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
I did a quick test.. With a diy I2C_GSP module and a diy FC. I had no problem connecting it without I2C errors. First i had errors but then i saw i had a Crius AIO defined and i only used a MPU6050 on the testFC... After i changed it no more errors. You can test it against stock V2.3 or 2.4 to ensur...
- Thu Jun 18, 2015 2:49 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
It's very unstable, rocks side to side a lot, perhaps due to wind or being very untrimmed? That's usually a sign of wrong CG..(Tail heavy) In the latest fw_Nav version i have added a field trim function. It only works via stick command by calibrating gyro inverted on the ground. And that means you ...
- Wed Jun 17, 2015 3:09 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
The PWM generating code is over my level!.. But i don't experience jitter on my planes. And i agree the loop time is way overkill for a plane! For the Gps functions. I have "disabled" a lot of "Not needed" code to fit it in a 328. A plane can fly with a much simpler GPS code. Que...
- Wed Jun 17, 2015 2:56 pm
- Forum: Boards
- Topic: Atmega 328P on Super X 125mm
- Replies: 9
- Views: 6928
Re: Atmega 328P on Super X 125mm
Conclution from the specs..
• Integrated DC/DC voltage booster/Step down for 5v 1~2 cell operation
Processor runs on 5V and regulator accepts 3.3 to 7.4 volts.
You should probably select 5V in the IDE.
It will fail flashing if it's wrong.
• Integrated DC/DC voltage booster/Step down for 5v 1~2 cell operation
Processor runs on 5V and regulator accepts 3.3 to 7.4 volts.
You should probably select 5V in the IDE.
It will fail flashing if it's wrong.
- Wed Jun 17, 2015 2:38 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
I think your Config.h is wrong.
The settings is 115200 and NMEA in the config.(My debug setup)
You need to adjust it to your GPS.
You need to set correct baudrate and protocol.
#define INIT_MTK_GPS Should be able to autoconfigure your GPS like settings in config file.
The settings is 115200 and NMEA in the config.(My debug setup)
You need to adjust it to your GPS.
You need to set correct baudrate and protocol.
#define INIT_MTK_GPS Should be able to autoconfigure your GPS like settings in config file.
- Sun Jun 14, 2015 6:39 am
- Forum: MultiWii tweaking - flying experience
- Topic: Extending Bluetooth Range
- Replies: 31
- Views: 14098
Re: Extending Bluetooth Range
Check if your phone support OTG.
- Tue Jun 09, 2015 2:44 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
In V2.3 you can use
nav_mode == NAV_MODE_NONE
Or why not update to V2.4 FixedWing With Waypoints?
nav_mode == NAV_MODE_NONE
Or why not update to V2.4 FixedWing With Waypoints?
- Mon Jun 08, 2015 6:44 pm
- Forum: Software development
- Topic: MultiWii OSD - MWOSD
- Replies: 873
- Views: 340272
Re: MultiWii OSD - MWOSD
I see the Homarrow is really lagging but it's helpful.. A little creepy music tough;) A warning about the latest Baseflight release... For Ublox init it is set to pedestrian mode. That means GPS will not work properly in speeds over ~105 km/h. That's ok for slower planes but many planes easily excee...
- Mon Jun 08, 2015 4:42 pm
- Forum: Software development
- Topic: MultiWii OSD - MWOSD
- Replies: 873
- Views: 340272
Re: MultiWii OSD - MWOSD
I've made a small function to Push MSP messages from MWIi. Mainly for a small Variometer/Telemetry project using a 328 in a soaring plane. Just make a timeinterupt push to get the data you want. msp_push(GPS_SERIAL,MSP_ALTITUDE); In this case get the Vario data sent o the GPS_SERIAL port via a simpl...
- Mon Jun 08, 2015 4:29 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Pasthru was a thin i came up with before Nav code. Just to be able to be able to take over manually. And to stop the gyros when i carry the model.(I usually walk ~100m to my "field".) It followed during the tests of RTH. And saved the model more than once when a certain idiot had made some...
- Sun Jun 07, 2015 4:58 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
rubadub wrote:what's the status of cruise mode and sticky rth?
CruiseMode seems to work.
I have only seen a few people who have tested yet.
Sticky rth is not done anything with yet.
Failsafe RTH is Sticky though.
It's only disabled if GPS mode is changed.
- Sun Jun 07, 2015 4:55 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
PatrikE, could you seperate the navigation stuff from the gps code? would make the code more readable. thanks Since the Navigation is integrated in V2.4 and my hack basicly just uses direction to waypoint and Alt error. FW code is isolated in a single void. The rest is just some small tweaks to con...
- Wed Jun 03, 2015 10:35 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
For Waypoints figure one is most desirable.
Keep a line between Wp's.
Some more D to stop the overshoot.
Maybe somewhere( P3, D1)
For RTH Booth pic 1 & 2 is quite ok
Is any modifications needed to MWii code to run this?
Keep a line between Wp's.
Some more D to stop the overshoot.
Maybe somewhere( P3, D1)
For RTH Booth pic 1 & 2 is quite ok
Is any modifications needed to MWii code to run this?
- Mon Jun 01, 2015 8:33 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
There's no Naze port of the GPS code from V2.4.
But the current Baseflight have RTH and PosHold integrated.
I hardly believe TC will let Waypoints be intgrared.
But the current Baseflight have RTH and PosHold integrated.
I hardly believe TC will let Waypoints be intgrared.
- Sun May 31, 2015 10:22 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
Ok.. I just uploaded the code in my trunk. m Here is a testflight with the code. m Switched to Mission at 0:10. I only cut throttle to loose altitude for landing at 2:40 Otherwise the flight was in mission mode. No other stick inputs. Weather here hasn't been the best for testing but maybe someone e...
- Sun May 31, 2015 9:16 am
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
I have never got it to track straight either. On the other hand i'm satisfied with getting the plane home with RTH. Played around a bit with PID's but don't get anything clearly better. Maybe the reaction time gets too long. It's more noticeable when flying waypoints. But there it seems I value may ...
- Thu May 28, 2015 10:45 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: mulitwii config 2.4 java problem easy fix (pictures)
- Replies: 10
- Views: 16599
Re: mulitwii config 2.4 java problem easy fix (pictures)
Great tips.
Could this be pinned at the top someway?
Could this be pinned at the top someway?
- Thu May 28, 2015 10:42 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: 2.4 config wont open
- Replies: 4
- Views: 1686
- Wed May 27, 2015 6:18 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Tri Coptor Tail Servo not working.
- Replies: 8
- Views: 2213
Re: Tri Coptor Tail Servo not working.
#define MEGA_HW_PWM_SERVOS That moves Tailservo to Pin 11 witch isn't available on your board. So comment it to get D2 back /* HW PWM Servo outputs for Arduino Mega.. moves: Pitch = pin 44 Roll = pin 45 CamTrig = pin 46 SERVO4 = pin 11 (aileron left for fixed wing or TRI YAW SERVO) SERVO5 = pin 12 (...
- Wed May 27, 2015 5:19 pm
- Forum: Ideas
- Topic: Airplane mode RTH
- Replies: 824
- Views: 336887
Re: Airplane mode RTH
If the 3D model drifts back when the board is tilted something is wrong. Probably sensor orientation. If you have this board MultiWii_PRO_Flight_Controller You should select FFIMUv2 I think. You can see the pinout in the chart here. m FW_Nav_140402 is the latest "stable" relese for FixedWi...
- Mon May 25, 2015 8:18 am
- Forum: Getting Started - MultiWii config and setup
- Topic: Does multiwii auto calibrate ACC on startup? How to stop tha
- Replies: 5
- Views: 2154
Re: Does multiwii auto calibrate ACC on startup? How to stop
Acc only calibrates on command.
Gyro calibrates every powerup.
Gyro calibrates every powerup.
- Sun May 24, 2015 6:50 am
- Forum: Getting Started - MultiWii config and setup
- Topic: 328P TriCopter, tail servo causes FC to lock up
- Replies: 5
- Views: 1534
Re: 328P TriCopter, tail servo causes FC to lock up
I guess your servo draws more current than your BEC can deliver.
FC will then brown out and reboot because of the power drop.
Test to use a larger bec or separate bec for the servo.
I had the same problem in air with a plane.. (Not healthy!)
FC will then brown out and reboot because of the power drop.
Test to use a larger bec or separate bec for the servo.
I had the same problem in air with a plane.. (Not healthy!)
- Fri May 22, 2015 7:13 pm
- Forum: MultiWii tweaking - flying experience
- Topic: Extending Bluetooth Range
- Replies: 31
- Views: 14098
Re: Extending Bluetooth Range
If you have a somewhat modern Android phone the 433 USB can be connected via OTG cable.
Fully compatible with EZ gui.
I thought i remembered someone presented a BT antenna hack here.
And found brewski's thread.
viewtopic.php?f=6&t=5250
Fully compatible with EZ gui.
I thought i remembered someone presented a BT antenna hack here.
And found brewski's thread.
viewtopic.php?f=6&t=5250
- Fri May 22, 2015 10:42 am
- Forum: General discussions
- Topic: Direct RC signal out from PPM
- Replies: 7
- Views: 2934
Re: Direct RC signal out from PPM
Hi, Did you set up correct in gui? Pull the Midpos slider fully to the left and it will change to channel instead of position. Camstab.png And don't activate Camstab in your case. You can also do it in config like this. #define SERVO_MIN {1020, 1020, 1020, 1020, 1020, 1020, 1020, 1020} #define SERVO...
- Fri May 22, 2015 10:23 am
- Forum: Software development
- Topic: MW2.4 stripped to the bone with GPS and Promini
- Replies: 4
- Views: 2085
Re: MW2.4 stripped to the bone with GPS and Promini
https://code.google.com/p/i2c-gps-nav/
It works on 2.4
No toggle Not with current code without some code changes.
And it consumes program space to.
It works on 2.4
No toggle Not with current code without some code changes.
And it consumes program space to.
- Fri May 22, 2015 9:34 am
- Forum: MultiWii tweaking - flying experience
- Topic: Extending Bluetooth Range
- Replies: 31
- Views: 14098
Re: Extending Bluetooth Range
Why not upgrade the link to 433mhz?
http://www.rctimer.com/product-834.html
Or wifi
http://ez-gui.com/manual/multiwii-clear ... ui-how-to/
http://www.rctimer.com/product-834.html
Or wifi
http://ez-gui.com/manual/multiwii-clear ... ui-how-to/
- Thu May 21, 2015 4:51 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Servo invert for a tricopter
- Replies: 8
- Views: 3427
Re: Servo invert for a tricopter
Try to erase Eeprom.
It's probably old scrap left from earlier installation.
It's probably old scrap left from earlier installation.
- Tue May 19, 2015 9:29 pm
- Forum: Software development
- Topic: MW2.4 stripped to the bone with GPS and Promini
- Replies: 4
- Views: 2085
Re: MW2.4 stripped to the bone with GPS and Promini
The Uart senses if you have GPS os FTDI connected.
But only one can be used.
I2C gps save some code size and you will have Uart free.
But only one can be used.
I2C gps save some code size and you will have Uart free.
- Tue May 19, 2015 12:35 am
- Forum: General discussions
- Topic: Direct RC signal out from PPM
- Replies: 7
- Views: 2934
Re: Direct RC signal out from PPM
boaterguy wrote:Okay I can do that, but I'm running a mega board so pins A0 and A1 aren't broken out, is there an easy way to change them?
Mega dont use A0 &A1.
Try
34/44 instead of A0
35/45 instead of A1
33/46 instead of A2
- Mon May 18, 2015 10:42 am
- Forum: General discussions
- Topic: Direct RC signal out from PPM
- Replies: 7
- Views: 2934
Re: Direct RC signal out from PPM
Cam Stabilisation is still the easy way to do it.
Just select in the servotab witch channel to controll with.
And don't enable Camstab with AUX switch.
Then it will just follow the RC channels.
Just select in the servotab witch channel to controll with.
And don't enable Camstab with AUX switch.
Then it will just follow the RC channels.
- Sat May 09, 2015 8:45 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Getting conf to start
- Replies: 3
- Views: 1609
- Thu May 07, 2015 11:24 am
- Forum: Connecting elements
- Topic: Interfacing MultiWii with another board
- Replies: 3
- Views: 1934
Re: Interfacing MultiWii with another board
All Uart's is set to 115200 in config.h
Look in the MWosd project to get some clues how to pull MSP.
Look in the MWosd project to get some clues how to pull MSP.