MultiWii

scrat

Hi. I have original rev5 board and load the latest FW from 24.4.2014 with bf configurator. Did 3 16 minutes FPV flights and nothing happened. But every time I load new FW on board, I go to CLI and type: defaults and hit enter. Only then I start to configure FC.

scrat

I don't know if this is the right thread but anyways...my two friends have Naze32 rev4 boards. And for both of them GPS doesn't want to work. They have the latest BF FW - when you've introduced EMF avoidance setting. Both of them have neo6-m gps. But those GPS works on rev5 board. What could be the...

scrat

I've previously posted here that I've fried the usb module on my rev5 while soldering. Later, I tried to use the FTDI to connect to the board which worked. But when I tried to update Baseflight to the latest version, it got stuck in the middle. After waiting for a couple of hours, I powered off the...

scrat

@Tr3TopFlyer A really good start is this thread i know its massive but i made my mini Quad fly just reading this thread Also really good start is the manual ?:) m Anyone need a case let me know . We went to town and printed ourself a bunch of naze32 rev 5 cases. Its impossible to find any so I have...

scrat

I don't know if this is the right thread but anyways...my two friends have Naze32 rev4 boards. And for both of them GPS doesn't want to work. They have the latest BF FW - when you've introduced EMF avoidance setting. Both of them have neo6-m gps. But those GPS works on rev5 board. What could be the ...

scrat

theailer wrote:You have to enable it in the CLI I think

Yes. That's right.

scrat

Then try to set LPF filter in config.h to 42Hz and load fresh hex to FC. Prior loading fresh hex...do eeprom_clear.

scrat

Thanks for that info Scrat. I have tried to fly the quad under these circumstances and it will basically bounce on the ground rather than hover. Also if the THR is increased it will shoot up really fast and go hard right. I- Term? Also are there any decent tutorials showing how to setup the sticks ...

scrat

For triming quad in acro mode this is fine. And use buttons on that side where you have stick for pitch and roll. But if you want then trim ANGLE mode...use my previous post.

Change the transmitter FW, because only then you'll see the light

Trust me.

http://code.google.com/p/er9x/ - er9x
http://www.open-tx.org/ - openTx

scrat

you can check if there are I2C errors on MWII Gui when quad is connected over USB...there is a counter.

scrat

Or this - my copter: GPS Pos Hold+ACC+MAG - baseflight FW https://www.youtube.com/watch?v=GkNA_nCsTM4

scrat

Do eeprom_clear in Arduino prior uploading fresh hex on FC.

scrat

theailer wrote:It overclocks the naze so there is less noise on the UHF band. Good to have if you use any type of long range system

I have LRS and Naze just spews on 432MHZ and I'm using 434MHz to 438MHz.

And from now on...will be naze always overclocked to 84Mhz?

scrat

Then just try again harakiri and see if it works.

scrat

First trim your quad in acro mode to perfect. Then switch to angle mode, fly, see where quad wants to drift, land, UNARM, switch to acro mode and then put throttle to full and use right stick to trim angle mode.

scrat

Acro mode is default mode when not using any other flying mode. For GPS hold I use: ANGLE, ALT, MAG in GPS POS H.

scrat

This is I-term doing. So fly with quadcopter and all will be ok. And remember. Set center sticks to 1500 and endpoints from 1000 to 2000.

scrat

Wich mode are you using? You need to test it in acromode. Trim acromode on your transmitter trims, not via stickcommands. Once acro is stable, take the next step to levelmode. Greetz Noc Also I'm not quite sure what you mean by transmitter trims, I used the clicking buttons below and to the side of...

scrat

Do you have I2C errors or maybe your eeprom is corrupted or not working?

scrat

scrat

I see something new at github.

What is: including EMF avoidance

Thanks.

scrat

Oj scorpioncek. Set sticks travel (end-points) from 1000 to 2000 or 1005 to 1995.

scrat

Because it is not compatible. This gui could destroy your settings..

scrat

Do eeprom_clear with Arduino software, then reflash board with FW and try again.

scrat

Hallo, ich habe auch ein NanoWii 1.0 Board. Ich habe einen simplen Spannungsteiler an die den PIN A3 angeschlossen. Die Dimensionierung des Spannungsteiler habe ich aus dem Dokument NanoWii FC User Manual Version 1.1. Ich habe verschiedenen Einstellungen probiert, nur alle leider ohne dass ich irge...

scrat

But you don't need to configure anything in u-center. Mwii sets every thing automatically.

scrat

As far as I know, RTH needs magnetometer to function properly.

scrat

BEWARE!! The latest firmware from GitHub scrambled some of my Aux switch connections? It seems 'Beeper' was inserted between GPS Hold and OSD Switch. Now my assignments for GPS Hold and GPS Home activate Beeper and OSD Switch, and my original OSD Switch function was lost. CHECK YOUR Aux assignments...

scrat

Hey guys is there any known Rev5 board cases available anywhere? or would it be hard to dremmel a rev4 case? not caring about looks i just want to mount it level and my quad doesnt have any mounting holes for FC and i dont really want to drill Hi. My friend is making cases for naze32 with 3d printe...

scrat

No. You uncommented: /******** special ESC with extended range [0-2000] microseconds ********************/ /**************************************************************************************/ //#define EXT_MOTOR_RANGE // using this with wii-esc requires to change MINCOMMAND to 1008 for promini a...

scrat

And do not use WinGUI with mwii v2.3.

scrat

Did you set maxthrottle to 1950 and maybe calibrated esc's with mwii software?

scrat

How did you activate GPS_Home?

scrat

dang... only if I asked here earlier... Made the mistake of throwing a hobbyking i86 board on my quad... armed it, flew around, landed, disarmed it... went to pull battery and it full throttled into my arm HD props cut as deep as graupners... Glad my naze is running! these are so much better Not go...

scrat

FYI. FatShark PilotHD camera also doens't like MAX chip. I have white lines behind text with pilothd camera and when I've add throttle...text was flickering. Now I'm using pz0420H camera and everything is ok. I was getting the flickering on throttle up until I added the ground line from the 12V cam...

scrat

If you have just one serial port on FC, then no. GPS or OSD.

scrat

I think you can't have gps and osd on one serial port.

scrat

Please post a picture how did you connect everything.

scrat

Hi scrat, it does indeed sound like a compatability issue, but I would have thought that fatshark would make it compatible with max based ezosd. Do you have any spec / details of the analogue signals - like how many tvl ? I can't seem to find anything. FYI. FatShark PilotHD camera also doens't like...

scrat

hola, podria ayudarme ?? estoy trabajando con una crius multiwii v2.5 con gps en i2c, modulo nav , bluetoot, lcd, TODO FUNCIONA O.K !!! PERO llegue al punto que no puedo usar mas que multiwii2.3 ya que las otra versiones "NAV" NO ESTA TERMINADO EL I2C PARA EL GPS, ADEMAS LOS SKETCH SON MU...

scrat

Connect your GPS to ucenter and reset it to default values. Then set in CLI gps_type=1 and gps_baudrate=0 or 1. That's it and gps must work. I have the same gps and it's working.

scrat

I'm using baseflight conf on mac os x 10.9.2 with no problem. naze32 rev5 - purple color.

scrat

In config.h...check this line and lower the value. But original value worked every time for me if quad was in gps pos hold and i've moved sticks. Never came back to same position. /************************ AP FlightMode **********************************/ /* Temporarily Disables GPS_HOLD_MODE to be ...

scrat

Unfortunately...your copter will never be still...even if your quad is not moving.

scrat

What atmega proc is on NanoWii FC? If you have USBasp, find original FUSES. Then set fuses with console avrdude with -B 1000 (this is for 1MHz internal clock) option and if this is success...burn bootloader but do not use -B 1000 option.

scrat

Yes. If you crash your copter while props are turning and battery disconnects itself. You can burn esc's. But comp_pwm doesn't work on all esc's.

scrat

deleted wrote:
It is a V5 board. I only bought it 2 weeks ago and its a red board.

If you need good naze32 case...PM me.

scrat

FYI. FatShark PilotHD camera also doens't like MAX chip. I have white lines behind text with pilothd camera and when I've add throttle...text was flickering. Now I'm using pz0420H camera and everything is ok.

scrat

scrat

Yes. You must connect battery to copter only then gps will work. I had have the same problem.

Search found 925 matches