MultiWii

scrat

Maybe this is CRIUS AIO clone.

scrat

OUT OF STOCK, ETA 05/19/2014

- http://abusemark.com/store/index.php?ma ... 3ejo9v51p4

scrat

BEC output of 5.3V shouldn't cause it- my BEC outputs 5.5V and no issues- the regulator on the Naze32 should easily be able to handle that. Are you powering anything off the Naze32 3.3V rail? Are you using 5V devices on the I2C bus? Any 5V inputs on the 3.3V GPIO pad or 3.3V ADC pad? I have a ublox...

scrat

I would like to see your CLI settings with BF firmware when your board freezes.

scrat

Please post your whole CLI and when status please. I would like to see what you have set.

scrat

Agree and true!

scrat

I have strange problem...but I don't know if is related to BF firmware and looptime. I have the latest BF from 30.4.2014 on my FC. And have set looptime to 3000 and have strange twitching when flying, but not the whole time. But when I leave looptime at default, there is no twitching? So...yesterda...

scrat

I think some months ago I have a problem when board was connected to computer only with USB - so GPS doesn't work if board connected only with usb and feature GPS was enabled...looptime was freezing every 5 seconds - but if board is connected with usb and quadcopter powered up with battery too there...

scrat

I would suggest going back to about April 5-6 for the hex. I have seen other people state the same issues, and mention this timeframe as a changing point, where the board freezing started to occur. Where did you see other people state the same issues? You joined this forum one day ago, and start sp...

scrat

Thanks I have tried exactly as you have recommended but it still does not appear to work properly. Here are a list of the settings from a dump of the config that are related to serial port or telemetry configuration. Are any of them incorrect? Am I missing out any other commands? feature PPM featur...

scrat

Quick question - are older versions of the firmware available anywhere? My Tricopter is rolling right pretty hard after the last flash and no amount of accelerometer roll trim via stick or GUI seems to affect the roll. Was wanting to flash back to the version prior to the one dated 4.30.14 but I ca...

scrat

If you fly in acro mode, copter should stay tilted. But if you fly in LEVEL mode then copter should go back to level.

scrat

Motor shouldn't power up. You must hear just esc beeps.

scrat

Because it is in mwii code and it is better then expo in your tx.

scrat

Turn off Tx then turn on Rx and then push FS button in Rx.

scrat

Ok, just realized I needed to comment out this line in def.h for the external compass...but could it have caused the crash when flying in angle mode(I don't remember if the compass was active btw). #if defined(FREEIMUv043) || defined(MICROWII) #define MPU6050 #define HMC5883 #define MS561101BA #def...

scrat

I have strange problem...but I don't know if is related to BF firmware and looptime. I have the latest BF from 30.4.2014 on my FC. And have set looptime to 3000 and have strange twitching when flying, but not the whole time. But when I leave looptime at default, there is no twitching? Yesterday I h...

scrat

I'm using baseflight conf.

scrat

So you can meet with tc and together check what s wrong

scrat

Use this map: m And click on your exact location and see mag declination and set it in CLI. With recent Baseflight Configurator updates, mag declination can be entered through the GUI... I think it's on the first page. Unfortunately, the format differs from the CLI input format. Yes. In CLI you can...

scrat

in the meantime, can you add more examples and their values to the code/wiki ? -1°2' => -102 10°18' => 1018 1°18' => 118 0°5' => 5 0°50' => 50 are those values even correct ? might even be easier to add mag_dec_deg and mag_dec_sec THe thing to remember that there are 60 minutes in one degree- so yo...

scrat

You have too much vibrations to sensors. So enable LPF filter in config.h and then try. And flash ESC's with bl_heli or simonk FW for faster response.

scrat

Do you mean that then we will set for examp. 11deg 8min like 11,8 in cli?

scrat

Use this map: http://magnetic-declination.com/

And click on your exact location and see mag declination and set it in CLI.

scrat

No. It will be 101

scrat

Thank you Scrat, So only Return to Home function in baseflight is working at the moment is that what you mean? (not Pos Hold) If this is the case then it makes sense why when i enabled Position Hold that my quad started to fly away lol.... Aslo Ive been reading heaps on setting the mag declination ...

scrat

I have strange problem...but I don't know if is related to BF firmware and looptime. I have the latest BF from 30.4.2014 on my FC. And have set looptime to 3000 and have strange twitching when flying, but not the whole time. But when I leave looptime at default, there is no twitching?

scrat

To Anyone that knows other than TC (GPS related) Can anyone tell me is the way to set a home point or do position hold etc is it all the same as multiwii's online info? Basicly is that where i should be reading for detailed info on using gps functions, I have the gps all on and working with satts l...

scrat

You can burn bootloader with Arduino. But I think you must burn bootloader to SMD atmel with internal clock 1Hz. ## FUSES Lo: FF Hi: DA Ex: 05 # 1) cd to Arduino 'hardware' folder # 2) connect everything and test that comms work CMD>> tools\avr\bin\avrdude.exe -C tools\avr\etc\avrdude.conf -c usbasp...

scrat

First thing you must do when you flash FW on FC is to calibrate ACC and MAG. Then you must first tune your copter to fly perfect in ACRO mode and then in LEVEL/ANGLE mode, then you must tune BARO and GPS position hold and then GPS returm to home. Only then you can use waypoints and other stuff.

scrat

With multicopters...the best thisng is to have all the same ESC's and with simonk FW.

scrat

Did you calibrated ESC's?

scrat

Check waypoint nav from EOSBandi.

scrat

I have just the right song for you two guys

But please no resentment.

http://www.youtube.com/watch?v=zsmUOdmm02A

scrat

felixrising wrote:Wait, what?!!!!

Are you saying you don't fly with all 8 channels maxed out at 2000uS? Do you even lift?!

Is this post for TC?

scrat

Sjefke wrote:
timecop wrote:Yes, you need to read, a lot.

I'm already doing that in this forum. Any tips where to start? I have a V5 naze.

Yes.

Set like this:

1. feature GPS
2. set gps_type=1
3. set gps_baudrate=0

That is it.

scrat

I have set failsafe with my Rx when out of signal Rx switch to RTH - But I always have BARO, MAG, ACC and GPS Home switched on together. But once I did try without ACC and quad did not do "rapidly return to the ground". Hmm. Good to know, I guess! I suppose the moral of the story is, chec...

scrat

Acro mode for returning to level is just user inputs.

scrat

Do not mix OPTO esc with normal esc. Use all opto or all normal. And if your board is resetting mid air...power the board from External UBEC.

scrat

Did you check in gui when sticks are centered...they are at 1500us?

scrat

Backup up all settings and hope you have source code v2.1 somewhere...the try v2.3 and if you're not happy...go back to v2.1.

scrat

RC Rate is how copter is sensitive to stick movements. But in general means that 0.3 is light acro, 0.5 is medium acro, 0.7 to 1 is almost insane acro. Expo is the same like Expo at your Tx but it is better to use Expo in GUI and not in your Tx.

scrat

Did you set your magnetic declination accordingly to your location?

scrat

Great. Now fly hard and safe

scrat

Noctaro wrote:Hi,
sounds good to me -> http://www.rchelimag.com/dji-lightbridge/
Does anybody know alternatives to this DJI System?
I like the idea of having digital HD Video livestream and RC controll in one.

Greetz Noc

I think DJI is the first one.

scrat

Post a picture how did you connected BT to FC.

scrat

Tr3TopFlyer wrote:Wow that's great. I didn't realize as I thought I read a post from timecop that these weren't supported but maybe an old post.

This is my best GPS Pos Hold with baseflight: http://www.youtube.com/watch?v=GkNA_nCsTM4 i think it's pretty good.

scrat

They aren't "supported" as TC isn't interested in GPS. However, they do work, after a fashion. You will need to do some tuning and don't expect the GPS hold to be super locked in. And, most importantly, as I have found out the hard way, if you bind return to home as a failsafe, make sure ...

scrat

Get a PPM receiver, end of story. LOL, Cheers Exactly my thought So i took it all out already and instead I am out flying now I just want to do it cause its possible But apparently I cant so instead I am out to play with it for now . waiting on D4R-II but even then i don't really think it needs GPS...

scrat

Yes man. This is THE REAL timecop - original maker of Naze32 board and yes...he is selling them: http://abusemark.com/store/index.php?ma ... oqonlr58d2 and if you order the board...you can get it in 3 days from Japan to your home

Buy original.

Search found 925 matches