MultiWii

shikra

@boogeyman12

can you pm me your settings when can't save - see if I can replicate the issue.

shikra

@spotter6

temperature... mmm sorry I actually though no-one ever used it! mmm will clearly have to reconsider that. I'll take a look next week and let you know.

mode - no idea with harakiri. maybe ask on that thread if its sent?

shikra

MSP value for current changed by a factor of 10 at some point during 2.4 dev.

not sure if related to point above, but though would mention

shikra

On 2.3 there is a patch available from Haydent that will enable the GPS time to be pulled through to the OSD. He was planning to make this available for 2.4, but its not done yet. Is it possible to pick up GPS time from the FC. I have a MultiWii PRO Flight Controller w/MTK GPS Module and I am playin...

shikra

I've tested with standard NEMA GPS emulator and also a UBLOX emulator and seemed to be OK I had an old UBLOX based crius GPS in my boy of bits. Tried that and it seemed to work OK. Was quite good because the connector fitted straight on - although I had to swap some of the pins around What GPS do yo...

shikra

Hello third and hopefully last pre-release with all the bugs / issues raised so far fixed (subject to testers confirmation) My only concern is compass heading / amperage from flight controller on baseflight and cleanflight is untested. also..... !! by popular interest... introduction of standalone G...

shikra

See next post

tungsten2k wrote:
"cell count adjustment via stick movement is non-functional (instead it adjusts the line below)."

-=dave

shikra

Yes, that would get my vote too. Thanks Deet.

Update the FAQ - its #13
https://code.google.com/p/multiwii-osd/wiki/FAQ

shikra

Amps adjust issue confirmed and fixed. Bug on the gui... Sim control OK for me. I think maybe this was an issue on the first pre-release... Hi Shikra, two issues I found with pre1.3: - Amps Adj. values will not be saved. Changing value via RC works fine. - Simulator Control can't be turned off Reall...

shikra

@ tungsten - try adding HEADINGCORRECT into config.h file as follows #ifdef BASEFLIGHT #define AMPERAGECORRECT // required to use Higher MW amperage but with less resolution #define HEADINGCORRECT // required to correct for MWheading being 0>360 vs MWII -180>+180 #endif I'm getting different feedbac...

shikra

@ tungsten2k thanks for time to test this out and provide the feedback. really appreciated. Yes sorry I did miss your comment. On the bug list to be tested and fixed this week #1 large adjustments when holding sticks - yes I think thats OK to do. Will put on list for 1.4 . It might be a little diffe...

shikra

@Hifly. thanks for testing.

Simulator button on GUI is corrected.
I'll check out the current sensor values.

shikra

Thanks for testing and feedback Deet.

shikra

Hey Deet Step1 - Basically uncomment this line... //#define OSD_SWITCH_3WAY 5 // Enables midpoint on specified channel (range 0-7 def=5) to turn off OSD. For 3 way OSD switch Step 2 - Change the "5" to match channel you want mid stick = blank screen to be activated. It doesn't need to be t...

shikra

Thanks for testing

+1 for this feature to be added.

shikra

@ABL for #FULLAHI - This is working OK for me so a little puzzled with this. I have extended a little further as requested. 5 "bars" either side of center instead of default 3 For optional low volts warning, I checked with low volts and see what you mean about the flashing "S". T...

shikra

Thanks ABL for disarmed/low volts I figured in flight that as the "disarmed" is unused it would be ideal utilisation of screen space. I didn't really pick up on the scenario on the ground in testing. If I add a check to display only if armed, I think that will look cleaner. for AHI - surpr...

shikra

ah - came back to update and see you posted too - I think if use standard arduino then fine. For those who wish to remove compiler / system events: Remove this line in MW_OSD_GUI // baudListbox.setValue(1); For those few who do use avrc compiler instead of old arduino new versions this may work as a...

shikra

Eijo - I'll take a look at this in the week. I can run the 64 bit on mine OK (hadron processor), but it does show errors in the cmd window. I don't see some of the ones you advise so maybe its machine specific. WIll update a bit later in the week. Suggest try using the 32 bit for now. I always use t...

shikra

For this beta release use:
#define WITESPYV1.1

All it is is a rename to try to better match WItespy's naming conventions rather than my made up one

Dunno why he changed. All its done is called a a whole load of hassle and confusion......

shikra

hello, first cut of the next release of MWOSD - R1.3 is here: m This is a pre- release. Please test carefully. There have been a lot of changes and maybe a few bugs, but it should be pretty close to final. Include a a mac compiled version Changes from 1.2 are: + OSD - alarms for distance, altitude, ...

shikra

This is controller.. All OSD does is display what controller sends. Pretty sure mine is close to zero at take off. I would expect controller to set it to zero reference upon arm, but no idea what it actually does. Mainly use multiwii Altitude in OSD does not reset to zero on a dragonfly/Flip 32 ? Is...

shikra

This will run fine standalone...

Use 1.2 with the 1.2+ gui and just enable the bits you need and where you want using switches and layout editor.

It also makes a great groundstation OSD...

shikra

No worries - thanks for the feedback. When your done, post layout. Be good to see all the creative options out there. 1.3 will not be a massive change compared to 1.2 - starting to get pretty full of features and memory So far: Customisable layout. Also addresses following requests: - "Disarmed...

shikra

Thsi one is posted quiet frequently. So far every one (I think has been down to the voltage needed by the max chip. I would recommend: #1 verify the voltage supplied by the programmer is 5v. Best place is on the actual pins of the OSD 6 pin header. It needs a full 5v and there have been quite a few ...

shikra

#1 output stage must be powered when programming fonts - n/a if using 5v like sounds you do
#2 programmer needs to be 5v - some are not - and some have the 5v/3.3v selector labelled wrong

shikra

Display voltage should be on (blue switch on right)
Use mwii should be off
Voltage adjust suggest start around 200

suggest try battery on bat 1 or 2 and see if either work.

Should see something other than 0

shikra

in config.h and also noted in the user guide...
WITESPY V2 - Enable to use the WITESPY V2 with different hardware

shikra

Thanks Pigsy Unfortunately I don't think there is a true fix for this. The cameras are working outside of the defined specification. You can try #3 from the FAQ to see if it helps.... But I can't remember if they are in 1.2 or in 1.3 code from SW repository m //#define FASTPIXEL // Optional - may im...

shikra

For same googlecode reason I had to move hosting of the pre-compiled downloads for MWOSD elsewhere.

This is what it looks like on googlecode now....
https://code.google.com/p/multiwii-osd/wiki/Downloads

Seems to work and is no real overhead.

shikra

Hi Exidous

I upgraded to Win7 64 bit with Java 1.8.0_25 and the GUI is working OK for me here. It previously had 1.7

shikra

@Bossa - not tried cleanflight, but on baseflight I think you have to enable it. If still not working, check baud rate OK

shikra

@bulesz:
Check your FTDI adapter is giving out +5v witha meter - don't rely upon what the screen print says !

@Gaijin - no idea other than check your jumpers and wiring is correct. i'd definitely check the OSD is correctly earthed.

shikra

@ Blackdog: For callsign - it should display callsign every 5 minutes for 4 secs. I just tried and it worked OK for me. Code now revised to display where you want via gui positioning and also the following can be amended in config.h: CALLSIGNINTERVAL - Define how frequently to display Callsign (in s...

shikra

edit:
Thanks for the info - so it hasn't changed then

shikra

Can anyone confirm if on latest baseflight, MWheading sent via MSP is in format 0 to+360 or -180 to+180
Am sure I saw something somewhere to say it changed, but couldn't find it on github.

shikra

I think the issue is the max chip needs a full 5v to operate, but the atmega starts working before the Max chip is ready. There is a default of 1 sec delay. In bad case maybe it needs longer, but that is still hell of a time to get to full volts. Maybe there is another issue not identified. For my c...

shikra

@fastrack stop timer on zero throttle - whats the requirement to have this instead of stopping when disarmed? It possible with code hack of course. battery low flash warning - added to wish list. Prob next release Power up issues... maybe try this in config.h //#define STARTUPDELAY 2000 // Enable al...

shikra

@davidross87 Please can you try this version out.. It is compatible with 1.2 OSD code... I have not done any help files and its only intended to be basic until someone has time to make it into a proper drag / drop GUI ..... + GUI - OSD layouts can be edited from GUI + GUI - 256 OSD layouts can be cr...

shikra

Hi Is it possible to make a GUI Linux64 of the current version 1.2? I don't get the 32bit version run on my ubuntu 14.04 64bit. Tried many things but no chance. GUI1.1 Linux64 is working very good. Thank you for that! Sure - no problem. probably next week though as bit tied up at moment. On a +ve i...

shikra

Snowboard_Nut's issue ssolve dove ron fpvlab. ahd 2 devices connected on same serial port at same time (frsky telemetry)

shikra

Any Processing / Java devs out there who fancy implementing drag / drop functionality for custom layouts?? Drag/drop + snap to grid stuff It looks quite straightforward but I am stuck for time. Almost finished putting all the screenlayout positions into XML file ready and that just leaves creation o...

shikra

@petronioaznar - am not familiar with it myself, but here is wiki
http://www.multiwii.com/wiki/index.php?title=Powermeter

@schnupperm - thanks for finding and fix. Updated...

shikra

Hi - in MWOSD, the MSP code for CELLS has changed - it is now 130. If you have existing multiwii code that used to work - need to update that MSP value.

Sorry, but unfortunately there was a clash with the new navi feature added for 2.4. Unfortunately they got the code officially first !

shikra

o_lampe wrote:
These last three lines are missing in the voltagecode, or are they hidden somewhere else?

in screen.ino...

if (Settings[S_MAINVOLTAGE_VBAT]){
voltage=MwVBat;
}

agree - its not consistent....

shikra

Worst thing of all is, I've set VBATTNOMINAL to 50.3V ( 15S LiFePO ) and the 11.6V value I got, should actually be 50.1V The whole MWii voltage monitoring seems to be limited to 3S? Also the battwarning levels were set accordingly to suit the 15S battery, but they were shown wrong in MWConf, too. M...

shikra

@Olaf Voltage reading trough MSP data seems wrong. I tried two different batteries on my DIY voltagedivider and both times I got different values in MWConf and from the OSD All the OSD does is to display what is sent by the controller. I have only ever tested it with the simulator. Will have to try ...

shikra

@petronioaznar - yeas - should update several times a second.

If you use volts from the flight controller (i.e. select use MWii), all calibration is on the controller and the scaling will not work.
Could that be it?

shikra

check out latest r1717

shikra

It means as you are actively inputting yaw then therefore no heading hold is required...

Search found 784 matches