Search found 14 matches
- Mon Jun 25, 2012 1:12 am
- Forum: General discussions
- Topic: Timecop
- Replies: 21
- Views: 6624
Re: Timecop
Perfect!
- Sat Feb 04, 2012 6:31 pm
- Forum: Software development
- Topic: dev MultiWii_dev_20120203 test
- Replies: 33
- Views: 12579
Re: dev MultiWii_dev_20120203 test
dongs wrote:You need to install 64bit version of Java. (ugh).
I have it, I use this machine for everything I do.
- Sat Feb 04, 2012 4:30 pm
- Forum: Software development
- Topic: dev MultiWii_dev_20120203 test
- Replies: 33
- Views: 12579
Re: dev MultiWii_dev_20120203 test
I can't get the 64 bit Windows version of conf to run. 32 bit starts fine but even trying to run the 64 bit version as administrator does nothing (I do say yes to the UAC prompt) . No errors in the event viewer, nothing in task manager.
- Thu Jan 05, 2012 11:15 am
- Forum: Software development
- Topic: Am I doing something wrong?
- Replies: 2
- Views: 1122
Re: Am I doing something wrong?
I did, that works fine. I can't get the dev GUI to show gyro or NK data.
- Thu Jan 05, 2012 3:57 am
- Forum: Software development
- Topic: Am I doing something wrong?
- Replies: 2
- Views: 1122
Am I doing something wrong?
If I use Arduino .23 to load the 1.9 sketch, and then use the 1.9 GUI all is well. If I load the dev sketch using Arduino 1.0, then the dev GUI I can see the stick movements but no gyro or NK data. Been back and forth too many times to count.
- Tue Jan 03, 2012 9:33 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: WMP bad?
- Replies: 10
- Views: 3476
Re: WMP bad?
OK, I tried the 1.9 sketch and gui and I see the data properly there. If I use Arduino 1.0 and the dev version of MultiWii I get no gyro data.
- Tue Jan 03, 2012 8:35 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: WMP bad?
- Replies: 10
- Views: 3476
Re: WMP bad?
OK, so I have header pins connecting them now. When I run the gui with just the Arduino board and the WMP connected should I see changes when I move the motion plus around? I hate to ask these stupid questions but I haven't found a quick start guide anywhere. It's funny, I make my living managing a ...
- Tue Jan 03, 2012 4:51 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: WMP bad?
- Replies: 10
- Views: 3476
Re: WMP bad?
I have all pro mini edge pins connected. Where are a4 and a5?
never mind, I see it now.
never mind, I see it now.
- Tue Jan 03, 2012 3:47 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: WMP bad?
- Replies: 10
- Views: 3476
Re: WMP bad?
I have it connected per this diagram.
- Tue Jan 03, 2012 1:01 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: WMP bad?
- Replies: 10
- Views: 3476
WMP bad?
I hate to ask total no0b questions but I have searched high and low and there is simply too much data to do a proper search. I think I may have a bad WMP. With just the Arduino and WMP connected should I see gyro data when I move the board around? I uploaded the sketch, and see RX data in the GUI. I...
- Mon Jan 02, 2012 9:26 pm
- Forum: Shields, boards and sensors
- Topic: Another no0b nunchuk question.
- Replies: 0
- Views: 922
- Fri Dec 30, 2011 3:19 pm
- Forum: Shields, boards and sensors
- Topic: Arduino sensitive to pins being soldered?
- Replies: 6
- Views: 2136
Re: Arduino sensitive to pins being soldered?
On a side note, why is the sketch a .ino file in the dev version?
- Fri Dec 30, 2011 11:09 am
- Forum: Shields, boards and sensors
- Topic: Arduino sensitive to pins being soldered?
- Replies: 6
- Views: 2136
Re: Arduino sensitive to pins being soldered?
I tried the dev version on 1.0 and it failed too.
- Fri Dec 30, 2011 2:35 am
- Forum: Shields, boards and sensors
- Topic: Arduino sensitive to pins being soldered?
- Replies: 6
- Views: 2136
Arduino sensitive to pins being soldered?
Ok, I have 2 of the Pro Mini's and they both had header pins soldered to them. I was trying to upload the 1.9 sketch with the Arduino .23 app on Windows 7. Both were failing with this error, avrdude: stk500_getsync(): not in sync: resp=0x00 avrdude: stk500_disable(): protocol error, expect=0x14, res...