Search found 14 matches

by TheX
Mon Jun 25, 2012 1:12 am
Forum: General discussions
Topic: Timecop
Replies: 21
Views: 2907

Re: Timecop

Perfect!
by TheX
Sat Feb 04, 2012 6:31 pm
Forum: Software development
Topic: dev MultiWii_dev_20120203 test
Replies: 33
Views: 5859

Re: dev MultiWii_dev_20120203 test

dongs wrote:You need to install 64bit version of Java. (ugh).


I have it, I use this machine for everything I do.
by TheX
Sat Feb 04, 2012 4:30 pm
Forum: Software development
Topic: dev MultiWii_dev_20120203 test
Replies: 33
Views: 5859

Re: dev MultiWii_dev_20120203 test

I can't get the 64 bit Windows version of conf to run. 32 bit starts fine but even trying to run the 64 bit version as administrator does nothing (I do say yes to the UAC prompt) . No errors in the event viewer, nothing in task manager.
by TheX
Thu Jan 05, 2012 11:15 am
Forum: Software development
Topic: Am I doing something wrong?
Replies: 2
Views: 475

Re: Am I doing something wrong?

I did, that works fine. I can't get the dev GUI to show gyro or NK data.
by TheX
Thu Jan 05, 2012 3:57 am
Forum: Software development
Topic: Am I doing something wrong?
Replies: 2
Views: 475

Am I doing something wrong?

If I use Arduino .23 to load the 1.9 sketch, and then use the 1.9 GUI all is well. If I load the dev sketch using Arduino 1.0, then the dev GUI I can see the stick movements but no gyro or NK data. Been back and forth too many times to count.
by TheX
Tue Jan 03, 2012 9:33 pm
Forum: Getting Started - MultiWii config and setup
Topic: WMP bad?
Replies: 10
Views: 1395

Re: WMP bad?

OK, I tried the 1.9 sketch and gui and I see the data properly there. If I use Arduino 1.0 and the dev version of MultiWii I get no gyro data.
by TheX
Tue Jan 03, 2012 8:35 pm
Forum: Getting Started - MultiWii config and setup
Topic: WMP bad?
Replies: 10
Views: 1395

Re: WMP bad?

OK, so I have header pins connecting them now. When I run the gui with just the Arduino board and the WMP connected should I see changes when I move the motion plus around? I hate to ask these stupid questions but I haven't found a quick start guide anywhere. It's funny, I make my living managing a ...
by TheX
Tue Jan 03, 2012 4:51 pm
Forum: Getting Started - MultiWii config and setup
Topic: WMP bad?
Replies: 10
Views: 1395

Re: WMP bad?

I have all pro mini edge pins connected. Where are a4 and a5?

never mind, I see it now.
by TheX
Tue Jan 03, 2012 3:47 pm
Forum: Getting Started - MultiWii config and setup
Topic: WMP bad?
Replies: 10
Views: 1395

Re: WMP bad?

I have it connected per this diagram.

Image
by TheX
Tue Jan 03, 2012 1:01 pm
Forum: Getting Started - MultiWii config and setup
Topic: WMP bad?
Replies: 10
Views: 1395

WMP bad?

I hate to ask total no0b questions but I have searched high and low and there is simply too much data to do a proper search. I think I may have a bad WMP. With just the Arduino and WMP connected should I see gyro data when I move the board around? I uploaded the sketch, and see RX data in the GUI. I...
by TheX
Mon Jan 02, 2012 9:26 pm
Forum: Shields, boards and sensors
Topic: Another no0b nunchuk question.
Replies: 0
Views: 396

Another no0b nunchuk question.

Never mind, I found the orientation here,

http://www.multiwiicopter.com/pages/multiwiicopter-wiki
by TheX
Fri Dec 30, 2011 3:19 pm
Forum: Shields, boards and sensors
Topic: Arduino sensitive to pins being soldered?
Replies: 6
Views: 821

Re: Arduino sensitive to pins being soldered?

On a side note, why is the sketch a .ino file in the dev version?
by TheX
Fri Dec 30, 2011 11:09 am
Forum: Shields, boards and sensors
Topic: Arduino sensitive to pins being soldered?
Replies: 6
Views: 821

Re: Arduino sensitive to pins being soldered?

I tried the dev version on 1.0 and it failed too.
by TheX
Fri Dec 30, 2011 2:35 am
Forum: Shields, boards and sensors
Topic: Arduino sensitive to pins being soldered?
Replies: 6
Views: 821

Arduino sensitive to pins being soldered?

Ok, I have 2 of the Pro Mini's and they both had header pins soldered to them. I was trying to upload the 1.9 sketch with the Arduino .23 app on Windows 7. Both were failing with this error, avrdude: stk500_getsync(): not in sync: resp=0x00 avrdude: stk500_disable(): protocol error, expect=0x14, res...