Search found 13 matches
- Wed Jan 06, 2016 3:41 am
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
Okay so I figured it out. I took all the wiring apart and carefully put them back together. I found out that I was hooking up the wrong wire to the Yaw pin. I mistakenly hooked up the Pitch wire to the Yaw pin. That explained why I "accidentally" got it to work while I was messing around w...
- Tue Jan 05, 2016 10:25 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
which LED is the red armed LED? opposite side of the LEDS 1-4? If so then it is on solid red as soon as I plug in the battery
- Tue Jan 05, 2016 10:24 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
When I was using the MWC v2.3 I was able to see the correct values from moving the sticks.
I just tried to do the same thing now with the newly flashed MWC v2.4 and the MultiWiiConf GUI is not picking up anything.
I just tried to do the same thing now with the newly flashed MWC v2.4 and the MultiWiiConf GUI is not picking up anything.
- Tue Jan 05, 2016 10:09 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
When you arm the motors by doing THROT back and YAW right, do the LEDs on your board flash?
Do the motors beep again?
When I try to arm the LEDs remain solid and no beeping sound is going on.
Do the motors beep again?
When I try to arm the LEDs remain solid and no beeping sound is going on.
- Tue Jan 05, 2016 10:05 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
Mode 2 . I also tried that .
- Tue Jan 05, 2016 9:49 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
So let me try to answer your questions based on what I have been doing for the last week. 1. I have binded and tested my TX RX using the Uno board to read in the values to make sure it works. 2. I have also watched the MultiWiiConf GUI to see the values change as I move the joysticks. 3. I also conn...
- Tue Jan 05, 2016 9:25 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
Okay so I flashed MWC 2.4 and still the same
- Tue Jan 05, 2016 9:19 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
i think i didnt set the right board
- Tue Jan 05, 2016 9:16 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
No I don't. Commented it out. But I am having trouble uploading it to my board. This report would have more information with "Show verbose output during compilation" enabled in File > Preferences. Arduino: 1.0.6 (Linux), Board: "Arduino Uno" Binary sketch size: 17,100 bytes (of a...
- Tue Jan 05, 2016 8:54 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
#ifndef CONFIG_H_ #define CONFIG_H_ /*************************************************************************************************/ /**** CONFIGURABLE PARAMETERS ****/ /*************************************************************************************************/ /* this file consists of se...
- Tue Jan 05, 2016 8:13 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
While I was trying to figure out how to set up endpoints and subtrim, I moved the two joysticks around in some sequence that I don't remember. All of sudden the motors started to spin. They "just work"... I got excited and unplug the battery to test it again and it is now back to the not w...
- Tue Jan 05, 2016 7:16 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Re: Motors won't spin
I bought the board from RTF site and the board is marked as flashed with MWC 2.3 so I assume that the config.h sketch has been configured "properly" ?
Are you suggesting to reflash the board?
Thanks
BP
Are you suggesting to reflash the board?
Thanks
BP
- Tue Jan 05, 2016 5:57 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors won't spin
- Replies: 24
- Views: 11156
Motors won't spin
Hello I am trying to build my first quadcopter. I am using these parts: 1. RTF multiwii pro 2.0 (marked as flashed with MWC 2.3 when bought) 2. Emax MTi 1806 motors 2280 KV 3. Emax Simonk 12A ESCs 4. Turnigy 3S 2.2A battery 5. FlySky Fs-i6 transmitter /receiver With the assumption the board was flas...