MultiWii

dialfonzo

Hi All,

I've been looking for similar functions myself.
Anybody been able to implement a simple Piezo Buzzer ?

dialfonzo

Hi All, We just release a quick new tutorial which explain the different steps involved to calibrate your UAV / Drone ESC (electronic speed controller). It cover the standard way but also the MultiWii procedure which does the calibration on all ESC's at once and the the right range of signal. http:/...

dialfonzo

After more investigation, it turn out that only the buzzer pattern was to be changed.
Now it work just fine..

dialfonzo

Thanks, just not sure why it was set to "vbatMin" instead of "analog.vbat" like the other levels.
Is that a mistake or there was an intended purpose for it..?

dialfonzo

Hi All, I was doing a complete testing in order to make a tutorial around the VBAT and BUZZER on MultiWii and i found an issue. When the triggers are set for the different Levels, the "Critical" don't seems to do anything. What i found so far (and i'm not a programmer). In the Alarms.cpp t...

dialfonzo

Hi All, The Lynxmotion UAV - FCT User Manual V1.0 is now released. As always, constructive feedback's are appreciated. It start with a "Quick Start" section and than give you all the detailed information about the FCT. Since the FCT is an ongoing project, we will release new guides once we...

dialfonzo

Hi All, We are now shipping Lynxmotion Quadrino Nano Flight Controllers to everyone who Pre-Ordered this product. In fact we started shipping Tuesday (14-04-2015). You should receive a shipping confirmation by email very soon if you haven't already. At the same time, we released the first version of...

dialfonzo

Hi All,

Sorry i posted this while on vacation on my phone. Here is a video we did for the new Quadrino Nano.

dialfonzo

Hi All, Sorry if this has been discussed before, i didn't find relevant information so i opened a topic. In the past, i was using a MultiWii board as a simple Servo Gimbal stabilisation. This is quite simple. But i was using PPM receiver and found that i had control with my Potentiometer Knob to adj...

dialfonzo

That's a very nicely done project.
I will have to try it myself..

Thanks a lot for the hard work.

Eric Nantel - DiaLFonZo

dialfonzo

- Reserved -

dialfonzo

Hi All, We are, at Lynxmotion, very proud and exited to introduce a new UAV / Drones flight controller born from a partnership between the well known FlyingEinstein and Lynxmotion team. We focused on many things on that project: The Press Release: RobotShop Continues its Expansion in the UAV Market ...

dialfonzo

if interested in optimizing loop time, the do yourself a favour and calculate that sin(whatever) once with a calculator and put the resulting number in that define. I am not a programmer, i can understand basic things but that's all. Kipkool told me that the calculating of the angle was made by the...

dialfonzo

Kipkool gave me this modified version. It integrate the angle of the V for frames that have other angle. //New Kipkool mixing for DiaLFonZo/Bledi VTail's //In config.h you must define that line in order to get the new mixing and rotations //#define MY_PRIVATE_MIXING "NewVTail.h" //Edited b...

dialfonzo

Thanks guys. I have fly mine here with the mixing posted. With all four motor of the same size and KV (4 identical motor) and 4 of the same prop also, it fly solid and when you yaw it stay flat. The thing is, i don't want to need to tell people to hack the mix to get a good flight. I think it should...

dialfonzo

Hi All, As a user of VTail frame, i would like to feel what others think. There is a bit of confusion around this config and teach people to use MultiWii for the first time and VTail also is a bit of a pain. On to of that there is different Hack around that (in my taste) improve a lot the capability...

dialfonzo

I don't know if anybody else will be interested...
But anyway this is the result...

http://www.youtube.com/watch?v=lTpY31mgWLo

dialfonzo

Very interesting...
I have that board with i think is the same oled display.

HD Image
http://farm9.staticflickr.com/8117/8622193508_91843d14d9_o.jpg

Did you code anything to work ?

dialfonzo

timecop wrote:lol is that the shit from phantom?

Exacly it is...!
With a non ajustable TX.

Got it from a Classefield just to play with it.

dialfonzo

Hi All, I posted my question on RCgroups but i think there is not much people there now.. lol I would like to know if anybody ever try a DJI PPM Receiver on MultiWii ? In the meantime i have soldered it to my board and to a test soon, when i have the time.. lol I would like to use that for a micro Q...

dialfonzo

Hi all, I would like to make you aware that the development release r1240 supports the change of the PPM sum input pin. This feature can be enabled by uncommenting the line #define PPM_ON_THROTTLE in the file config.h. As a result of this change, the sum input has to be made avaliable at the standa...

dialfonzo

Hi copterrichie, Do you think the thing is doable if the motor output pin is changed ? Since i am not a programmer, just understand basic of programmation, could you do a sample multiwii file so i can test it ? Thanks a lot http://www.multiwii.com/forum/viewtopic.php?f=15&t=2888&p=28553#p285...

dialfonzo

Ive been reading that topic but im not sure if it applies to this? Hes trying to use an output pin as an input pin, but were just trying to get it to move from one input to another? I already posted as well, all I got was an odd response though. :') http://www.multiwii.com/forum/viewtopic.php?f=6&a...

dialfonzo

I found that thread while searching
viewtopic.php?f=8&t=1625

dialfonzo

Hi All, I have a friend that need to relocate his PPM input signal to another pin cause the board broke at that point. Is there any way to change the pin to any other normal RX input pins ? I have search but can't find how it's done in the software. My skills in programming are limited. I found : #d...

dialfonzo

I have see (with my eyes) Johny yesterday.

I know he face a lot of proplem in the last couple of month..

dialfonzo

Hi JohnyGab,

Can you make a simple stock Multiwii 2.1 file that work with the Rushduino OSD.. ?
So we can all start from there.

Thanks for a fast answer

Eric Nantel
DiaLFonZo-Copter
info@dialfonzo-copter.com

dialfonzo

I didn't follow for a while.
But is there compatibility with Multiwii 2.1 now ?

dialfonzo

Très beau..

Faudrais que je regarde si j'en ai un autre qui traine. J'en ai un sur mon MicroQuad.

dialfonzo

I am following but don't know for the MPU
Put some pictures..

dialfonzo

Let us know..

dialfonzo

Wow.. nice board..

dialfonzo

chilled wrote:eBay or Dfrobot, which is the best source?

DFrobot is the maker... so i would say there.
Mine came direct from them.

dialfonzo

Yes i have see that one..

Both ARM processor so.. in somewhere.. they will be same

dialfonzo

Hi All,

I am not a programmer.. so that said
Anyone think that going with a 32-bit arduino would be a good idea.

Thinking of the faisability of the thing...

Link
http://www.robotshop.com/productinfo.aspx?pc=RB-Lea-01&lang=en-US
http://leaflabs.com/devices/#Maple

dialfonzo

I have two that are availible if anyone want one..

dialfonzo

Bledi wrote:normal je lui file des coup de pieds au c...

LOL
Il faut que j'ai cette version 8...!!

dialfonzo

WOW... !
Tu as fais des progrès enorme depuis la dernière fois que j'ai regardé...!!!!!

dialfonzo

Thanks..!
Need to re-assemble my 500 before trying

dialfonzo

Video i just made...!

http://www.youtube.com/watch?v=93xjcSOKSrE&feature=youtu.be

dialfonzo

Thanks, but i don't want to use it wit FBL right now.
Just normal flybar to have "AutoLevel" feature..

dialfonzo

120deg CCPM swashplate.
I will test it on ground without motor anyway...

I didn't dig into the code yet.. but is the motor going to MultiWii or not ?

dialfonzo

Ok
Mine don't have any vibrations, everything is balanced.
A lot less than my MultiCopter.. lol

Have to look and try...

dialfonzo

Hi, I have stopped my tests because of oscillations on cyclic servos and have not returned to those tests after exploded head on HK-450. The funny part it is that now you can get true FBL unit that is cheaper than Arduino and WM+ m Regards Andrej Yes i know, but i have already "Many" Mult...

dialfonzo

Anybody ever fly it finaly ??

dialfonzo

Hi all,

Just wonder if anybody ever port the multiwii to an Helicopter purpose ?

Like auto level ... i would like to try that on my t-rex...

Eric

dialfonzo

KeesvR wrote:I'm a happy person who made you happy.

HéHé...

I'm really happy now..!
350mb of video take time to upload..

Curiously that DEV version feel more stable than the 1.9

dialfonzo

A big thanks to ronco and other who may have work for that mod...!

Awesome it fly just as it should.
Camera Stabilisation A0 and A1
HEX configuration with motor on pin5 and pin6

Uploading a video and will add it.
Sorry but my servo have some play so the cam move a bit..

UPLOADED....!!!
http://www.youtube.com/watch?v=MJghxAHC ... e=youtu.be

dialfonzo

Tested Motors but don't look to have any signal on 5 and 6 ESC are beeping like no signal and don't spin when the copter is armed. I attach my config files ok.. you are using the wrong (old and not working) output.ino code... use this one http://www.multiwii.com/forum/viewtopic.php?f=8&t=1069&a...

dialfonzo

Tested Motors but don't look to have any signal on 5 and 6
ESC are beeping like no signal and don't spin when the copter is armed.

I attach my config files

Search found 62 matches