OK solved .
I had a messed up configured GPS module.
I had to reset/erase the config and revert to the factory default.
I started over and now it works perfectly.
Cheers.
Franky
Search found 13 matches
- Mon Feb 29, 2016 8:10 pm
- Forum: General discussions
- Topic: Yellow lines on the WinGUI map screen ????
- Replies: 3
- Views: 2551
- Sun Feb 28, 2016 6:04 pm
- Forum: General discussions
- Topic: Yellow lines on the WinGUI map screen ????
- Replies: 3
- Views: 2551
Re: Yellow lines on the WinGUI map screen ????
Hello Kbev.
I'm using EosBandi WinGUI on my home PC.
I have doubled checked all the setting you advised.
1 - Correct magnetic declination.
2- ACC and MAG calibrated as usual.
3- My GPS ( U-blox NEO-6) hooked-up as it should.
4- WP enabled.
I'm not using android EZ GUI.
Franky
I'm using EosBandi WinGUI on my home PC.
I have doubled checked all the setting you advised.
1 - Correct magnetic declination.
2- ACC and MAG calibrated as usual.
3- My GPS ( U-blox NEO-6) hooked-up as it should.
4- WP enabled.
I'm not using android EZ GUI.
Franky
- Sun Feb 28, 2016 3:57 pm
- Forum: General discussions
- Topic: Yellow lines on the WinGUI map screen ????
- Replies: 3
- Views: 2551
Yellow lines on the WinGUI map screen ????
Once connected my multiwii AIO pro board to the PC . I opened the Multiwii WinGUI (EosBandi) , and while I was planning for a mission, yellow lines appeared on the map screen (see picture below). They went off with the CLEAR Route button. But they appeared over and over again. Is it normal ? The GPS...
- Mon Dec 07, 2015 9:55 pm
- Forum: Software
- Topic: What firmware ?!?!
- Replies: 3
- Views: 6892
Re: What firmware ?!?!
Hi Kbev, that's the point. I read Crius AIO can load waypoints through MISSION PLANNER software once MEGAPIRATE is flashed into the board. http://www.unmannedtech.co.uk/manuals/all-in-one-pro-board-setup-with-megapirates-code http://fpvcentral.net/2013/06/multiwii-2-2-vs-megapirate-2-9-beta/ ( I kno...
- Mon Dec 07, 2015 1:04 pm
- Forum: Software
- Topic: What firmware ?!?!
- Replies: 3
- Views: 6892
What firmware ?!?!
What firmware to be used for a CRIUS AIO Pro v2, MegapirateNG or MultiWii v2.4 ?
Any advantage one over the other ?
In MultiWii v2.4 I don't see the version for this flying board in the list, it says only //#define CRIUS_AIO_PRO ?
Franky
Any advantage one over the other ?
In MultiWii v2.4 I don't see the version for this flying board in the list, it says only //#define CRIUS_AIO_PRO ?
Franky
- Thu Nov 12, 2015 6:55 pm
- Forum: General discussions
- Topic: Satellite maps ....
- Replies: 0
- Views: 2357
Satellite maps ....
Just few questions for the experts.
Where sattelite maps are saved when cached in WIN GUI EosBandi ?
There is any way to choose the tile map zoom level to be saved ?
It looks like there is no control for it.
It takes for ever to download the maps for the offline use. Is it normal?
Franky
Where sattelite maps are saved when cached in WIN GUI EosBandi ?
There is any way to choose the tile map zoom level to be saved ?
It looks like there is no control for it.
It takes for ever to download the maps for the offline use. Is it normal?
Franky
- Sun Nov 08, 2015 2:24 pm
- Forum: Frames
- Topic: Motor level .....
- Replies: 1
- Views: 3603
Motor level .....
I have a question for you guys.
I'm building a tricopter frame .
The tail yaw system brings up the rear motor a couple of centimeters above the front motors.
Do the motors need to be all at the same level ?
From a physics point of view it should work the same.
Franky
I'm building a tricopter frame .
The tail yaw system brings up the rear motor a couple of centimeters above the front motors.
Do the motors need to be all at the same level ?
From a physics point of view it should work the same.
Franky
- Thu Oct 29, 2015 10:17 am
- Forum: Connecting elements
- Topic: PIN connectors on the board ...what for ????
- Replies: 1
- Views: 1770
PIN connectors on the board ...what for ????
Please, can someone tell me what these pins are for ?
Just to better know my board.
Thanks.
Franky
Just to better know my board.
Thanks.
Franky
- Fri Oct 23, 2015 7:14 pm
- Forum: Connecting elements
- Topic: Bluetooth 4.0 BLE on a Multiwii board ?!?!?
- Replies: 5
- Views: 6124
Re: Bluetooth 4.0 BLE on a Multiwii board ?!?!?
Cereal ,
Is this the good one you are referring http://www.ebay.it/itm/HM-10-Bluetooth-4-0-Module-Interface-Board-CC2541-xDrip-MultiWii-iOS-HM10-UK-/252065518558?hash=item3ab04693de:g:FhoAAOSwv0tVcfP7 ?
Thank you for your advice.
Franky
Is this the good one you are referring http://www.ebay.it/itm/HM-10-Bluetooth-4-0-Module-Interface-Board-CC2541-xDrip-MultiWii-iOS-HM10-UK-/252065518558?hash=item3ab04693de:g:FhoAAOSwv0tVcfP7 ?
Thank you for your advice.
Franky
- Fri Oct 23, 2015 6:43 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: GPS mission HOW TO
- Replies: 9
- Views: 4930
Re: GPS mission HOW TO
Kbev, I'm running v2.3 because using ver 2.4 gave me errors opening WinGUI .
So you are saying , if I change from 240 to 230 version within the Multiwii.h TAB of the Multiwii.ino it should work with the WinGUI EOsBandi 2.3 ?
Is this what you mean ?
I did'nt know about that trick .
Franky
So you are saying , if I change from 240 to 230 version within the Multiwii.h TAB of the Multiwii.ino it should work with the WinGUI EOsBandi 2.3 ?
Is this what you mean ?
I did'nt know about that trick .
Franky
- Fri Oct 23, 2015 5:37 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: GPS mission HOW TO
- Replies: 9
- Views: 4930
Re: GPS mission HOW TO
Hi Kbev , I have a Multiwii SE v2.5 FC. I saw these videos on YOUTUBE https://www.youtube.com/watch?v=UJrErUlnJSI , https://www.youtube.com/watch?v=7sExKKzNJVc end this one https://www.youtube.com/watch?v=sVw2dcRbgzo . So I ordered this GPS module from e-bay http://www.ebay.it/itm/2C-GPS-NAV-Module-...
- Fri Oct 23, 2015 2:21 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: GPS mission HOW TO
- Replies: 9
- Views: 4930
GPS mission HOW TO
I'm just learning because new to the copter world.
Please can somebody tell me how to activate a GPS mission once I uploaded to my board throught the WinGUI EOsbandi 2.3 ?
Do I need to use any AUX channel ??
Any "HOW TO" explanation somewhere ??
Thank you .
Franky
Please can somebody tell me how to activate a GPS mission once I uploaded to my board throught the WinGUI EOsbandi 2.3 ?
Do I need to use any AUX channel ??
Any "HOW TO" explanation somewhere ??
Thank you .
Franky
- Fri Oct 23, 2015 1:32 pm
- Forum: Connecting elements
- Topic: Bluetooth 4.0 BLE on a Multiwii board ?!?!?
- Replies: 5
- Views: 6124
Bluetooth 4.0 BLE on a Multiwii board ?!?!?
Hi everybody ! Is it possible to use a bluetooth 4.0 BLE module on a multiwii FC SE 2.5 Crius clone like this one http://www.banggood.com/BLE-CC2541-Bluetooth-4_0-UART-Transceiver-Serial-Module-p-961876.html ? If it's OK, how to set it up ? It should work with this IOS free-software https://itunes.a...