Search found 19 matches
- Fri Jun 30, 2017 6:26 am
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
Hi kbev Arducopter and Multiwii are two different firmwares that can run on the same hardware. I agree with you, that's why I do not understand why the installations of the last firmware from mission planner does not work. Actually, I must install old firm via Flashtool or IDE Arduino and it's OK to...
- Thu Jun 29, 2017 7:45 pm
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
yes, but arducopter or multiwii are based on same Atemga 2560, I don' understand the subtleties...
- Thu Jun 29, 2017 11:59 am
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
Ok with Arduino, but in Mission planer there this possibility, but impossible to selected versions. (same in windows)
- Wed Jun 28, 2017 10:00 pm
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
So, is it possible to load this firmware directly by Mission planner ????
And where do you find this version ?
All the best..
And where do you find this version ?
All the best..
- Mon Jun 26, 2017 9:48 pm
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
Hi Kbev, can you explain me why MW ez pro3 don't support the last firmware ?
Thank you
My gps,is,ok now
Thank you
My gps,is,ok now
- Sun Jun 25, 2017 6:24 pm
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
Re: MegapirateNG on Multiwii EZ pro 3
Hi, you have raison, if I do update by mission planner, system not respond.....
If I load with flash tool, it's ok.
So I have just a problem to configure my serial gps, I don't know witch port use ?
If I load with flash tool, it's ok.
So I have just a problem to configure my serial gps, I don't know witch port use ?
- Sun Jun 25, 2017 7:41 am
- Forum: Software development
- Topic: MegapirateNG on Multiwii EZ pro 3
- Replies: 11
- Views: 8495
MegapirateNG on Multiwii EZ pro 3
Hi alls,
Can you tell me if it is possible to use MegapirateNG on Multiwii EZ Pro3 ? (not Blacked edition, mine has Compas)
http://www.readytoflyquads.com/multiwii-pro-ez3-0-flight-controller-w-gps-option
Thank you.
Can you tell me if it is possible to use MegapirateNG on Multiwii EZ Pro3 ? (not Blacked edition, mine has Compas)
http://www.readytoflyquads.com/multiwii-pro-ez3-0-flight-controller-w-gps-option
Thank you.
- Sat Sep 19, 2015 5:41 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
Other question please, do you know the leds function on Mega PCB ?? LED1, 2, 3, 4. ???? The accelerometer has significant variations in Z when the quad is laid flat, and I accelerated the engines, is it mormal ? New link for web site now building: http://dubuf.free.fr/maxfly/index.html
- Fri Sep 18, 2015 8:35 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
Hi , Yes it's ok now, the Failsafe work fine. Thank you. Also, now, I don't understand very well the switch config on TX (aux1 et aux2), because in multiwiicong, there is 3 positions switch, and in mine, I have only 2 positions on button. Can you explain me, and what is the best config for the switc...
- Thu Sep 17, 2015 8:50 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
hi,
I think alls mods are ok. (execpt failsafe, again same problem)
See new config.h and dump gui conf
http://dubuf.free.fr/karmania/index.html
refresh explorer !
Chat translator is ok, thank you for this information.
I think alls mods are ok. (execpt failsafe, again same problem)
See new config.h and dump gui conf
http://dubuf.free.fr/karmania/index.html
refresh explorer !
Chat translator is ok, thank you for this information.
- Thu Sep 17, 2015 6:19 am
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
hi kbev,
I do your instructions!!!! sorry but my English is very poor, very difficult for me to write exactly what I think.
I comeback later.
@+
I do your instructions!!!! sorry but my English is very poor, very difficult for me to write exactly what I think.
I comeback later.
@+
- Wed Sep 16, 2015 9:14 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
hello, yes it's only when i uncomment failsafe. For the others parameters, I havn't changed, it's a default parameters. I have read with attention yours comments, I continu my investigations. Also, Today i have tested my first fly, chooooooooooooooooo, the quad takes off and slides on the side and b...
- Tue Sep 15, 2015 8:55 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
no alls channels are in range 1007- 1998 about, center 1500
- Tue Sep 15, 2015 8:00 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
hi alls,
When I uncomment Failsafe, impossible to rearmed motors, what do you think about it ?
tnk's
When I uncomment Failsafe, impossible to rearmed motors, what do you think about it ?
tnk's
- Mon Sep 14, 2015 8:49 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
kbev and Ed, Thank's again for this adjust. Yes my MultiwiiMEGA3.21 include alls sensors, I have only uncomment in config.h "#define MultiWiiMega". Ok for calib MAG outside, you have probably raison. My DM is not 4.02, mine is : +0° 52' Declination is POSITIVE (EAST), but i don' t no trans...
- Mon Sep 14, 2015 7:54 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
- Mon Sep 14, 2015 7:27 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
Re: need support to MEGA3.21 multiwwi 2.4
thk's ED, When i calibrate ESC, there are no props, and alls motors in same time. (I use special function in config.h) For MAG , I'll test later.. For my motor rear left, Yes i have the problem in output bars only when I move quad (pitch front), normaly two motors rear must be speedy, but left, is n...
- Sun Sep 13, 2015 7:09 pm
- Forum: Shields, boards and sensors
- Topic: need support to MEGA3.21 multiwwi 2.4
- Replies: 26
- Views: 7829
need support to MEGA3.21 multiwwi 2.4
Hi alls, I have finish my quad, also I have 3 problems: 1>Difficult to calibrate MAG, after calib, directions are not exact. (I calibrate during 30 seconds, during blink leds ) 2> My GPS (MN8 Ublox) fixe correctly satellites (multiwiiconf) , but I not sure alls config.h parameters are correct, where...
- Sun Sep 13, 2015 6:50 pm
- Forum: Software
- Topic: muliwwi winGUI on windows10 problem
- Replies: 0
- Views: 5948
muliwwi winGUI on windows10 problem
Hi alls,
No problems to connect my MEGA 3.21 with Multiwiconf on windows 10, but impossible with multiwi winGUI.
My COM port is correctly detected in multiwwi winGUI, i try différents speeds, but impossible connect, I have un message it don't find com port.
Can you help me please.
regards
Frank
No problems to connect my MEGA 3.21 with Multiwiconf on windows 10, but impossible with multiwi winGUI.
My COM port is correctly detected in multiwwi winGUI, i try différents speeds, but impossible connect, I have un message it don't find com port.
Can you help me please.
regards
Frank