MultiWii

Tifani

Czesc!
Norton nie lubi Twojego programu

Pozdrowienia
Tomek

Tifani

Hi !
Update:
I,m able to make BT shield to talk to computer-computer or Android-computer but only in "terminal mode" not any luck using it as "serial cable" for MultiWii.
Tom

Tifani

Hi ! I have Seeduino BT shield from RadioShack @ $19.99 I was able to configure shield (change name, set baud rate to 115200) but nothing more. Did anyone have luck using this shield ? I was trying to find TX signal from Seeduino board with osciloscope (USB disconected) but no luck. Any help please....

Tifani

Excellent! I have been waiting for this. Thank you, EOSBandi! Upon startup, the wizard appears freezed. I found others have encountered the same problem before. I think it simply doesn't show the navigation buttons, they are below the lower border, but the window cannot be resized. However, using l...

Tifani

Hi !
Remove all red (5V) wires from ESC RX plug (thin 3 wires) except 1 - or better remove all and use BEC to power RX and Arduino.
Regards
Tom

Tifani

Hi !
My recent computer scan show this - anybody can confirm is something wrong with this files ?
Regards
Tom

Tifani

Hi !
Post Afroflight questions in 32 bit section of furum so You get faster answer (maybe from designer).
I have all red wires removed and BEC to supply 5V.
Good luck
Tom

Tifani

Hi !
I made simply board for limited space
Regards
Tom

Tifani

Hi !
Thanks a lot - now is working - I get confused by version 1.8p2 and forget about symmetric servos.

Any recommended PID settings for 55" (1.4m) wing (extended Great Planes Slinger)

Thanks again
Tom

Tifani

Hi ! I have try flying wing but something is wrong (me ?) Looks like Pitch & Roll channels are swapped - please look at attached video of GUI. First I move TX Pitch Stick - servos react in opposite direction Later I move TX Roll Stick - servos move in the same direction Next I move sensors in Ro...

Tifani

Hi ! Is Roll and Pitch switched in 2.1 or I did something wrong ? If I move Pitch Stick or sensors in Pitch axis my "servos" go in opposite direction. If I move Roll Stick or sensors in Roll axis my "servos" work in the same direction. Also no ACC stabilization No servos connecte...

Tifani

Hi !
Tx --> Rx What You Transmit is going to Receive line.
Rx <--Tx and v/v

Tom

Tifani

Hi ! I tested FailSafe with Spectrum AR6200, AR6110 & HK OrangeRX R610. After TX off Throttle graph in WinGui drop to 910 and motors drop to MINTHROTTLE value (1120 for SS ESC). If Yaw stick is hold left during TX power of FC will disarm after little time - this indicate than RX is sending some ...

Tifani

@jy0933 Hi ! Both GUI's original and this one work with BT dongle @11520 with little problems (reseting BT helps) try to download Asus BT stack (free driver). I'm using Asus USB/BT - windows will create two serial ports (in my case 34 & 35) connection is possible only on port with higher #. Peop...

Tifani

Win 7/64 System font set to 125%

Tifani

I tested FailSafe with Spectrum AR6200, AR6110 & HK OrangeRX R610. After TX off Throttle graph in WinGui drop to 910 and motors drop to MINTHROTTLE value (1120 for SS ESC). If Yaw stick is hold left during TX power of FC will disarm after little time - this indicate than RX is sending some signa...

Tifani

Hi ! Thanks for 2.1 !!! On bench test FailSafe is only turning motors off - no switching Level ON and no (MINTHROTLE+200) then TX is back on FC is also back on. Can somebody explain ? My config.h : #define FAILSAFE #define FAILSAVE_DELAY 10 #define FAILSAVE_OFF_DELAY 200 #define FAILSAVE_THROTTLE (M...

Tifani

Hi ! I like Your App a lot, very clear display, speech is great for blind (reading glasses). I have Pitch and Roll display reversed (pitching sensor move Roll circle, tilting sideways move Pitch circle - Circle View is correct . Connect/Disconnect/Exit button or via phone menu will be great, also ke...

Tifani

@captaingeek
Yes - just a few generations ahead.
MapleMini use 32-bit ARM Cortex M3 microprocessor @72Mhz.

Tifani

Amen.
But .....
Alex mentioned a few conditions for 32bit future and one of them was free programming environment - after reading about Maple IDE I took a risk

.
Anyway with my programming skills I can not enter in any discussion - so I,m safe

Regards
Tom

Tifani

Hi !
Can this board be use as future replacement of ProMini http://www.sparkfun.com/products/11280
Tom

Tifani

Old fashion 300 baud telephone modems was effective over very narrow freqency telephony audio. Anyway if I find right protocol I will try it this weekend. Tom P.S. Long time ago I play with pocket radio (data over FM audio channel @ 2meters 144 Mhz) during very rare aurora condition I have 400 km co...

Tifani

No Sir ! People do not have skills (except a few) I have Apache OSD - http://www.aeorc.com/english/?product-387.html Manufacturer claim it will be implemented in future but looks like nothing is going on. Anyway I was thinking (no skills) to try to use audio channel to send data. Looking for protoco...

Tifani

Hi !
Tested with newest dev. version - works fine over FTDI or BT (BlueSkyRC @11520)
Thanks
Tom
P.S. It will be great to have choice of old serial protocol - just dreaming.

Tifani

Hi !
Yes it is 32.
Just reporting.
I had very little time so maybe I did something wrong - I can not make it work at all.
Will try again tomorrow with controller only and different copter.
Tom

Tifani

Hi !
Thanks !!!
Downloaded. Will test when comeback from work.
Regards
Tom

Tifani

Hi !
Thanks a lot.
Yes it is v1.37 30.

Tifani

Hi !
I have strange behavior on my Samsung Galaxy S (2.3.5) - MultiWii 2.0 BlueSky RC BT module @11520Wii
http://www.youtube.com/watch?v=aeaAe3pCEzg
As You can see all graphs jump without touching radio.
Ice Wind MultiWiiConfigurator work fine on the same setup.
Regards
Tom

Tifani

Hi !
I use BlueSky RC BT module @115200 v2.1B hangs when using bluetooth connection. Previous version work fine with the same module.
Regards & Thanks
Tom

Tifani

Hi !
As I signalized before some older and blind (like me) peoples use large windows system fonts what lead to unexpected display problems if display is formated without possibility to autoscale it.
Anyway THANKS A LOT.
Tom
P.S. info for some over reacting people - this is not critique.

Tifani

@Hamburger
I loud and clear underscore my appreciation for Your work.
If You call two post flooding - sorry - check my total # of my post - sorry again - i post in serch of help.
So let me admire and appreciate MultiWii and it developers in silence.
Tom

Tifani

Yes - You are 100% right. But I just have lost ability to tune it with my Android phone - now I have to learn new way (terminal) and as soon I learn will be new dev version not compatibile with my skils So I will try to do my best to not be just complaining p...y. As soon I learn how (and wind in Wi...

Tifani

Hi Alex ! Thanks for replay. I'm little more than complete nob. I did some programming. I had my first "computer" in 1980. Now i'm CNC programmer/machinist. I did also little electronics (more hobby than work). So if I have problems what about average guys. This was not critique - this was...

Tifani

Hi ! So - my copters (2 Tris and 1 Quad - even very old with HK401 gyros) can hover on gyro only almost hands free for many seconds and when switch to level mode they will fly away in random direction (after calibrating it and trimming). Looks like more peoples have this problem. Maybe step by step ...

Tifani

Hi !
I know difference between Autolevel and PositionHold and I know than even perfectly balanced craft will drift even with little wind.
But what changes (hardware/software) we can make to have good (better) Autolevel mode ?
Regards
Tom

Tifani

Hi ! Dear Developers. First of all - it is only my two cents. With constant changes (specially to serial communication) & new sensors, bells & whistles MultiWii is growing instead of improving. Basicly only Gyro mode is working well, Level mode is far from good. It will be nice to use Androi...

Tifani

http://www.seeedstudio.com/depot/maple-mini-p-861.html
I just find this:
http://www.digilentinc.com/Products/Det ... PKIT-UNO32

Tifani

http://leaflabs.com/docs/maple-ide-install.html

Tifani

Maybe stupid question but ...
I saw Maple board @ Sparkfun, it have STM32 it have some compatibility with Arduino and IDE is very close.
So - maybe this could be less painful way to move forward.
Tom

Tifani

Hi !
+1 on perfect basic configuration (gyro+ACC).
+1 on documentation. I know I can find all needed info but it is spread around web.
Maybe 2 different releases like V.2.0 Basic and V.2.0 Bells&Whistles
Regards
Tom

Tifani

Thanks a lot !
I did not connect NCS
Tom

Tifani

Hi Alex!
Can You please share Your connection diagram for 5050.
Looks like I'm doing something wrong.
Thanks
Tom

Tifani

Hi !
After applying your patch I was able to compile - will test afternoon if I finish soldering new controller.
I run Windows 7 -64bit but only 32bit version works (the same for original MultiWiiConf)
Thanks
Tom

Tifani

Thanks !!!
Now is working.
Thanks for Your work.
Regards
Tom

Tifani

Hi Alex ! If I try to do "SVN Checkout" I'm getting this error "Server sent unexpected return value (405 Method Not Allowed) in response to.." The same with other MultiWii repositories - what I'm doing wrong - I just want to download. I tried link for "not members" but ...

Tifani

This way also do not work.

Lets cut this - I do not want to take any more of Your time.
I quit.
Regards
Tom

Tifani

Hi !
But I can not see my picture - just paperclip symbol and file name.
Sorry to all members for taking your time but I can not sleep.
Regards
Tom

Tifani

THANKS !!!
But I have to be retarded - no luck ???

Tom

Tifani

Hallo ! Guys !
I was sure than this (and other) forum is about helping each other.
Why all of You ignoring my question "how to attach pictures to the post".

Daniel - I tried to help You - why You can't help me ? Do not tell me You don't know.

Regards
Tom

Tifani

Hi ! For me look like one of Avago ADNS family - I have ADNS5050, it have very similar hole pattern - do not have "dashes" Maybe this one: http://zener.ru/catalogue/Sensors,%20Transducers/Optical%20-%20Mouse%20Sensor/ADNS-2610/ or http://www.diylive.net/index.php/2007/07/20/diy-mouse-scann...

Search found 63 matches