MultiWii

I have same problem on my gimbal. Using A0 & A1. When the Tilt-Servo moves it starts to shake. In the gui i can see that when it starts shaking all RX inputs is flickering between 1000-2000. It seems that the servo is overloading the output. Iw'e tested some servos and it occurs on another to. ...

I re-do my quad yesterday, today I tried to fly it wont even take off at full throttle, here some pics: 20111125_145131.jpg m i should have takent the video horizontally all prop are properly mounted as it should be and I doubt the motor can't lift the quad full specs Motor 1811-2000kv SS 8-10A ESC ...

Excellent . With the small items, I would PM/contact the BlueSkyRC shop and explain what you want and the situation. He is an excellent guy to work with and is more than fair. I would recommend that too, very prompt reply , multi rotor community in my country is quite small so getting this kind of ...

zarkon wrote:love to have the mini quad frame but the int shipping cost more expensive than the frame it self

quoting myself Thanks to david I get a flat rate shipping for the shield and the mini quad frame!!hopefully I can get it next week!!

what has been done:

- reset throttle range
- forgot to check the roll value

I'll try to do the trim as bill mentioned later

Thanks!

love to have the mini quad frame but the int shipping cost more expensive than the frame it self

I see it from the GUI and from the observation it quite obvious as when throttle up right motor will lift off first , I'll check the roll value later when i get back from work, as for the throttle range it I'll will try to reset this too

Thanks!

Hi, I noticed on my tri/quad my right motor always have the highest value, which cause my quad/tri always fly to left as the power to the right motor is not balance with the left, is there anyway to correct this beside trimming on the TX? and it some how it hard to even hover w/o it going right and ...

ah so not defining it in the config are not enough to disable them? I thought when you didnt enable it in config it wont be enable at all, I'll try it later when i get back from work

Thanks

You should be able to connect and see rotation of copter. Anyway you should be able to connect and read/write values if you dont have connected any sensor... I can connect and read the value but no rotation because I don't have any sensor correct? i try to connect to it when it running on Lipo but ...

Hi, I wondering what should i expect when using the GUI, I only have WMP no acc/nunchuk, will the Quad display move or static? also when I try connecting with the GUI when my Quad is powered by Lipo with all wiring connected the GUI go crazy, I don't have acc/baro but GUI said I have and the connect...

tried to dl does not seem the 1.7 zip is valid the files is corrupted, or maybe it just me, I have a new sensor, now no data from gui I really not sure what wrong now, i have new sensor new arduino mega but nothing works Edit: It working now I accidently swaped sda and scl, it confirm that the previ...

look nice for all in one it even supply the code for multiwii 1.8,

decided to unsolder the nunchuck still having problem with gui, some time it detect it when it donafter a few min it just lost connection

i still havent got a new wmp to test yet maybe tomorrow i try to get the stuff for more testing, anyone have the old version of mwc? 1.7 maybe?

same thing happen configurator can detect the mega w/o the wmp plugged in, when i plug the wmp configuration just wont connect to mega/pro mini my WMP connection check with multimeter does not find any short connection.jpg I will try the new WMP tomorrow seem nothing it working with this one somehow...

ahh seem someone else having the same problem, I'm going to resolder the WMP again, ordered a new mini pro and a WMP, I have Mega 2560 board but not sure how to connect WMP to it :p

Hi, having a problem with the setup, my multiwiiconf detected arduino fine when the WMP is not connected but as soon as I connect the WMP it stop getting any data from the arduino, really not sure what wrong I have soldered and resoldered the connection verify everything with multimeter to make sure...

seem like i got the same board on my WMP i just bought few minutes a go, cost me $10 here a clearer pictures MotionPlus_A.jpg MotionPlus_B.jpg you can see the cable slot at the back, so we can actually use that instead of soldering directly on the board correct? and the strip with the gold connector...