MultiWii

Hi, I want to start flying FPV, there are so many types and brands and don't know what to choose... I live in belguim and fly a 2.4ghz fasst futaba. i think the best way is 5.8ghz (by law). 500mW will be enough for me. can someone give me more advice wich brand i should choose? I also want to add te...

Hi, I was testing the gps indoor and outdoor... doesnt make a big difference...the baud rates are at 57600. i am thinking to buy an ublox GPS but i dont know witch one i should buy, Lea 6H or NEO 6m, or other? what is the difference. The FC from hobbyking i dont want to change because this tiny thin...

Hi, I am using the multiwii pro (hobbyking) the red one that comes with a gps module. i have managed to make it work, but i am verry dissapointed about the accuraty. is there anything that i can do about it? I have 9 satelites and when the copter is on the same possition i see in the gui that it mov...

Well i live in europe, is it a good choice then? Or Will The accuraty be bad?

Why Should i use an external mag? Is it better?
What About this one?
http://www.hobbyking.com/hobbyking/stor ... uracy.html

So, i have to uncommented The init gps, upload The code and then comment it again and select nmea?
Can YOU post a link where to buy The ublox?
And how to make it work? I would be verry happy

Hi, thanks for the reply, I use the multiwii pro V2.3 from hobbyking (the red one) with a MTK 3329 GPS: m I already tried this: //#define NMEA //#define UBLOX //#define MTK_BINARY16 //#define MTK_BINARY19 #define INIT_MTK_GPS Uploaded to the FC, power down wait for 5 min. and power up and then loade...

hi all, i managed to setup and fly my Multi rotor. now i want to go one step further an duse the gps rth and pos hold. when i open the gui i notice that i have the "gps fix lost" also on the map the position is not the right one...i dont get any satelite. i am using the Multiwii pro V2.3 (...

Hi all,

I managed to solve this problem. i bought a new flight controller plugged it in and this one stays connected without interruption. i thing there was been a connection problem in the cable, or in the connection (mini usb)

I think i have found my problem, i have 4 esc that acting strange when i put them directly in The received. Totdat i ordered 8 New ones, without bec, The previous ones were with a bec, is it possible that this is The problem?

Hi brewski, i have flyed The copter with other codes, this problem popped up sind i try using eosbandi... I use turnegy multistar, i red The manual But there is nothing to set in The esc About throttle calibration...

Ok i managed to solve this problem by commenting all The things concerning the tx in The code, next problem i have is that when arming The motors dont spin. They start sponning after The throttle is over The middle possition, Also The 4 of The motors acting strange and are nog in sync with The other...

Hi ZED961 i have the same problem you had, In the GUI i dont see any live stick responses from the TX. what exacly was the problem?

Hi brewski,
thanks for the link! I have istalled the code but i have some issues... if i startup the GUI, is see that the sensors are working, but the navigator engine is disabled. also if i move the TX commands, nothing is changing... Do i have to change something in the code?

I use The multiwii pro 2.0 ( hobbyking)

Well, like i Said, i tryed another pc, and it is The same. I dont have another FC. I want to buy a New one... Hoping this Will be a sollution...

Hi waltr, If i Wait a a while ( app. 2 Hours) i can achieve a connection, i uploaded Some data and after a while The conn. Dissapear, pop up again, dissapeared again, an so on for a few times until The conn. Is complete dead... I am thinking that there is a default on The board itself, is that possi...

I connected the Multiwii FC for the first time, with succes. i uploaded the code, made the copter flying, i want to adjust some things and now my PC doesnt reccognize the board anymore. i tried another PC , the same problem! anyone some advice?l the problem begon when i tried to connect the GUI 2.3 ...

Hi,

Is there anyone that have experience with Octocopters? I found many codes on the internet. most of them are not working. Does somebody have a code (and using it in his octo) that want to share with me?

Is it possible to use The gui 2.3 instead of The 2.1
I think i have to update The firmware, are there turorials to do The upgrade?

Hi, I build a octocopter and i think he is ready to fly, There are Some features that i want to use like level the Copter when i hit a switch. To do so, i switched the level on in The gui ( aux 1) The problem is when i do this, the copters board is armen (led lights up) But the motors arent running....

Hi, i try to adjust it to 1500 But it is always a little less or more, (1499) is that a problem?

Indeed, that was the problem, how can you adjust it? i did it in the radio and it is working, is this the right way to fix this?

Hi,

I have made an octo with the multiwii pro 2.0 FC. i loaded the sketch code and in the multiwii GUI i can see that all those things work fine.
if i try to arm the motors, they wont start.

any one knows what i am doing wrong?