Search found 33 matches
- Mon Feb 25, 2013 3:37 pm
- Forum: Software development
- Topic: Altitude Hold/Advanced Failsafe solutions by NHA
- Replies: 270
- Views: 131927
Re: Altitude Hold/Advanced Failsafe solutions by NHA
If we use 5 baros in the board, kill the 2 most off values and take the average of the closest value, dosn't this give a more precise altitude reading??
- Wed Oct 03, 2012 3:11 pm
- Forum: Shields, boards and sensors
- Topic: No start with #define GIMBAL uncomment
- Replies: 4
- Views: 1731
Re: No start with #define GIMBAL uncomment
I need this explanation. Thanks
- Wed Oct 03, 2012 3:00 pm
- Forum: Software development
- Topic: DEV r1129 serial GPS MTK3329 bug
- Replies: 4
- Views: 2397
Re: DEV r1129 serial GPS MTK3329 bug
I have MTK3329.
Should I choose in code to use NMEA or MTK?
Will this GPS work in binary mode?
Should I choose in code to use NMEA or MTK?
Will this GPS work in binary mode?
- Fri Sep 28, 2012 1:54 pm
- Forum: Shields, boards and sensors
- Topic: SOLVED! GPS bad flash. need help please..
- Replies: 6
- Views: 3841
Re: SOLVED! GPS bad flash. need help please..
I do not know version 1.4? were did you get it?
Try installing the MTK3329_A1.5E_20110118_10Hz_115200.bin.
Its the one that I'm presently using with good results
Try installing the MTK3329_A1.5E_20110118_10Hz_115200.bin.
Its the one that I'm presently using with good results
- Tue Sep 11, 2012 1:55 pm
- Forum: Shields, boards and sensors
- Topic: SOLVED! GPS bad flash. need help please..
- Replies: 6
- Views: 3841
Re: SOLVED! GPS bad flash. need help please..
I'm no Guru.
Are you sure that you are selecting the correct download agent for your GPS chip?
Are you sure that you are selecting the correct download agent for your GPS chip?
- Mon Sep 10, 2012 2:46 pm
- Forum: Software development
- Topic: GPS integration
- Replies: 1724
- Views: 887603
Re: GPS integration
EmmeDi8 wrote:Hi,
this is the version of my gps.
How can I check if is lastest version and support binary protocol ?
Thanks
Is you r GPS MKT 3329 or MKT 3339?
- Tue Aug 07, 2012 1:59 pm
- Forum: Shields, boards and sensors
- Topic: 10Hz GPS thread
- Replies: 84
- Views: 125205
Re: 10Hz GPS thread
Since my last post I've tested also U-Center and noticed that the GPS signal was intermittent (did not tested in Multiwii). So I decided to use has I said the DEFAULT BUTTON ON NMEA OUTPUT SETTING. That button change GLL to 1 and GSV to 1. Is this good? were can I find the meaning for these abbrevia...
- Sun Aug 05, 2012 3:48 pm
- Forum: Shields, boards and sensors
- Topic: 10Hz GPS thread
- Replies: 84
- Views: 125205
Re: 10Hz GPS thread
Hi haydent
I used the MTK3329_A1.5E_20110118_10Hz_115200.bin but changed the NMEA Output Settings to Default and then confirmed it.
Also I deactivated SBAS.
Don't know if I'm doing the right thing?
I used the MTK3329_A1.5E_20110118_10Hz_115200.bin but changed the NMEA Output Settings to Default and then confirmed it.
Also I deactivated SBAS.
Don't know if I'm doing the right thing?
- Sun Aug 05, 2012 3:13 am
- Forum: Shields, boards and sensors
- Topic: SOLVED! GPS bad flash. need help please..
- Replies: 6
- Views: 3841
SOLVED! GPS bad flash. need help please..
Dear sirs By mistake I loaded with Flash Tool v122 the MTK_AllInOne_DA_MT3329_v4.02 download agent and the AXN2.10_5156_3339_1152.1101000.10 firmware in to a Mediatek 3329 GPS (Skylab). The problem is that my GPS is the 3329 and after loading 3339 firmware It does not work and when I try to flash It...
- Tue Jul 31, 2012 3:06 pm
- Forum: Connecting elements
- Topic: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
- Replies: 7
- Views: 13589
Re: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
UPDATED INFO - TESTED/WORKING Buzzer/led Lipo monitor connects to pin 32 (with 1kohm resistor) (identified has CamPitch on this board) (needs external driver to sound the buzzer) - TESTED/WORKING Lipo voltage sense: connects to pin A0 from A0~A5 plug - TESTED/WORKING Led Flasher: I changed code and ...
- Sun Jul 29, 2012 10:29 am
- Forum: Connecting elements
- Topic: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
- Replies: 7
- Views: 13589
Re: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
Can't find there useful info for all my questions: I'm moving from Crius SE to Crius AIO Pro, and still trying to find were to connect things. Can you help me check if this ir correct?: - NOT TESTED/DOES NOT WORK Buzzer connects to pin 32 (with 1kohm resistor) (identified has CamPitch on this board)...
- Fri Jul 27, 2012 11:52 am
- Forum: Connecting elements
- Topic: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
- Replies: 7
- Views: 13589
Re: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
Can't find there useful info for all my questions: I'm moving from Crius SE to Crius AIO Pro, and still trying to find were to connect things. Can you help me check if this ir correct?: - Buzzer connects to pin 32 (with 1kohm resistor) (identified has CamPitch on this board) (needs external driver. ...
- Fri Jul 27, 2012 7:56 am
- Forum: Connecting elements
- Topic: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
- Replies: 7
- Views: 13589
Re: Connecting BUZZER, LED to Crius AIO PRO / Mega 2560
Same here.
Were to connect:
- Buzzer (needs driver?)
- Led (Lipo status)
- Lipo voltage sense
- Led Flasher
- Led landing lights
Were to connect:
- Buzzer (needs driver?)
- Led (Lipo status)
- Lipo voltage sense
- Led Flasher
- Led landing lights
- Mon Jul 23, 2012 5:06 pm
- Forum: Buy & Sell
- Topic: SOLD: CRIUS SE MultiWii 10DOF
- Replies: 2
- Views: 2315
Re: SOLD: CRIUS SE MultiWii 10DOF
I accept Paypal but I'm sorry to tel you the item is already sold. I've updated the thread name
- Fri Jul 13, 2012 1:25 am
- Forum: Buy & Sell
- Topic: SOLD: CRIUS SE MultiWii 10DOF
- Replies: 2
- Views: 2315
SOLD: CRIUS SE MultiWii 10DOF
http://img651.imageshack.us/img651/2694/img20120713010224.jpg http://img406.imageshack.us/img406/8123/img20120713010202.jpg MWC MultiWii SE Standard Edition 49USD shipped worldwide with tracking number. (sponge is to protect baro from light and wind) This is RTF multiwii controller. ·Dimensions 50 ...
- Mon Jul 02, 2012 12:35 am
- Forum: Software development
- Topic: Patch: LED Flasher
- Replies: 35
- Views: 18931
Re: Patch: LED Flasher
Great: Thanks. Now I understand
- Sun Jul 01, 2012 4:16 pm
- Forum: Software development
- Topic: Patch: LED Flasher
- Replies: 35
- Views: 18931
Re: Patch: LED Flasher
Are the comments correct??? Please answer my doubts //#define LED_FLASHER //Activates flasher code //#define LED_FLASHER_DDR DDRB //I don't know what it does //#define LED_FLASHER_PORT PORTB // What is portB? //#define LED_FLASHER_BIT PB4 //Port B4 is digital port 4 (D4) from multiwwi connection sch...
- Fri Jun 08, 2012 12:24 am
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
How do I know that GPS is locked and that is enabled for position hold and RTH? The statusLed is normally off when card is unarmed. With GPSFix it will start to blink fast 3-4Hz when board is unarmed. The board only check for Gps at boot. Crius board dont have a reset button and you must disconnect...
- Wed Jun 06, 2012 11:51 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
If I connect the Crius SE to GUI from FTDI cable pins and GPS in serial port pins that will not work?
Is that what you are saying?
With this setup all functions from GUI work, besides the GPS that does not report no info.
How do I know that GPS is locked and that is enabled for position hold and RTH?
Is that what you are saying?
With this setup all functions from GUI work, besides the GPS that does not report no info.
How do I know that GPS is locked and that is enabled for position hold and RTH?
- Wed Jun 06, 2012 2:43 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
I tried DOSD GPS with several baud rates in GPS_BAUD and GPS_PROMINI_SERIAL. The GPS led blinks, but in GUI never catches GPS sats. I was thinking if udi123 link is any good to connect to CRIUS in serial or I2C m I'm planning on connecting the GPS to PC trough the FTDI cable and use miniGPS tool to ...
- Mon Jun 04, 2012 1:25 am
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
Finally I tested Dragon OSD GPS serial connect to 328P (Dev0528) Issues: - Cannot load all settings in 328P by lack of space. Must disable camera tilt, trigger and failsafe that I wanted. - GPS is recognized has green in GUI and its led blinks, but does not pick up info in GUI (alt, lat, lon, sats.....
- Sun Jun 03, 2012 11:28 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
1 problem... 328P is starting to get small.
I want to activate Camera Triguer, and Tilt, and Failsafe but there is no space available.
What can I remove to free space?
I want to activate Camera Triguer, and Tilt, and Failsafe but there is no space available.
What can I remove to free space?
- Sun Jun 03, 2012 7:53 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
I Wrote incorrectly my previous post What I meant was: //#define GPS_SERIAL 2 // should be 2 for flyduino v2. It's the serial port number on arduino MEGA #define GPS_BAUD 115200 #define GPS_PROMINI_SERIAL 57600 // Will Autosense if GPS is connected when ardu boots!..... This is the correct setup to ...
- Fri Jun 01, 2012 3:32 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
Thanks Dramida and PatrikE. I'm going to try tonigh this GPS m, that I use with Dragon OSD. Do you think it will work? Do I need to configure anything in this GPS. If so... how to? I will do the following step by step: 1 - Connect the 4 wires from the GPS to Serial Port on Crius SE (GND,Vcc,Tx,Rx) 2...
- Thu May 31, 2012 12:56 pm
- Forum: Software development
- Topic: GPS on Crius SE board
- Replies: 121
- Views: 71838
Re: GPS on Crius SE board
DRAMIDA can you please post some pictures of the GPS connected to the CRIUS SE?
Do you think that this GPS will work connected to the serial port?
http://www.dragonlabseu.bigcartel.com/product/10hz-gps
Do you think that this GPS will work connected to the serial port?
http://www.dragonlabseu.bigcartel.com/product/10hz-gps
- Wed Jan 04, 2012 4:39 pm
- Forum: Software development
- Topic: Arduino V1.0
- Replies: 3
- Views: 1530
Re: Arduino V1.0
Sorry. please close or delete this thread.
This issue is in study in viewtopic.php?f=8&t=955
To be soon solved.
This issue is in study in viewtopic.php?f=8&t=955
To be soon solved.
- Wed Jan 04, 2012 11:28 am
- Forum: Software development
- Topic: Arduino V1.0
- Replies: 3
- Views: 1530
Arduino V1.0
I installed software Arduino v1.0 and some errors are reported during the Verify process with Multiwii 1.9 and developers preview from December. If camera trigger and tilt are activated more errors are reported. Errors are about HardwareSerial lib. Do you have the same problems? any solutions availa...
- Mon Nov 28, 2011 4:30 pm
- Forum: Shields, boards and sensors
- Topic: ArduIMU V2 (flat) and Multiwii 6DOF
- Replies: 9
- Views: 4121
Re: ArduIMU V2 (flat) and Multiwii 6DOF
This team used the ArduIMU to control a quad an they have the code in bottom of the page.
http://www.diydrones.com/profiles/blogs ... r-part-iii
I believe they do not use Multiwii, but could be interesting to look because they have Sonar and IR and its code, that soon will be developed for multiwii (I hope).
ArduIMU V3 is starting to sell soon.
http://www.diydrones.com/profiles/blogs ... r-part-iii
I believe they do not use Multiwii, but could be interesting to look because they have Sonar and IR and its code, that soon will be developed for multiwii (I hope).
ArduIMU V3 is starting to sell soon.
- Sat Nov 19, 2011 11:02 am
- Forum: Shields, boards and sensors
- Topic: Dragon OSD and MultiWii
- Replies: 0
- Views: 1141
Dragon OSD and MultiWii
I want to do FPV with a Tricopter, and I have a Dragon OSD that already uses ArduIMU v2 (flat) to obtain artificial horizon.
Do you have any idea or experience on how to connect this to Multiwii in a Tricopter configuration?
Do you have any idea or experience on how to connect this to Multiwii in a Tricopter configuration?
- Sat Nov 19, 2011 11:00 am
- Forum: Shields, boards and sensors
- Topic: ArduIMU V2 (flat) and Multiwii 6DOF
- Replies: 9
- Views: 4121
ArduIMU V2 (flat) and Multiwii 6DOF
Does anyone knows how to connect this IMU to MultiWii?
- Thu Nov 17, 2011 2:34 pm
- Forum: Shields, boards and sensors
- Topic: New Shield - Bob's Super Simple Shield 1.0.3 for the ProMini
- Replies: 9
- Views: 4021
Re: New Shield - Bob's Super Simple Shield for the ProMini
I would buy one if shipping wasn't so high to europe.
- Thu Sep 22, 2011 6:25 pm
- Forum: Connecting elements
- Topic: Arduino Nano Wiring to WM+Nunchuk
- Replies: 2
- Views: 1936
Re: Arduino Nano Wiring to WM+Nunchuk
thanks! will test it
- Thu Sep 15, 2011 10:50 am
- Forum: Connecting elements
- Topic: Arduino Nano Wiring to WM+Nunchuk
- Replies: 2
- Views: 1936
Arduino Nano Wiring to WM+Nunchuk
I think most of connections are similar to Arduino mini, but I can't identify from the images in this forum were should I connect the orange wires in Arduino Nano?