MultiWii

Which of these connection types is required to get all of the data from a Naze32 onto the MinimOSD? You want MSP so scenario 1, 5 or 8. You cannot have 1 or 5 active on two different ports at the same time so you probably want 1+8 or 5+8. You can have MSP at the default 115200 baud rate and attach ...

I went "back" to the 3-pos type firmware using the latest on github yesterday and all my problems seem gone, I can save stuff regardless if GPS is active or not and it seems to work over bluetooth as well. The only thing that doesn't work for me, and it seems you're aware, is in EZ-GUI on ...

I'm happy to report that changing my BT module's baud rate to 19200 and setting msp_baudrate in CLI to 115200 made it possible to use my OSD on serial 1 at full speed, and connect to the quad over a BT module on soft serial port 1 (RC ping 5+6). The problems I saw when trying to runt at 9600 are go...

I'm happy to report that changing my BT module's baud rate to 19200 and setting msp_baudrate in CLI to 115200 made it possible to use my OSD on serial 1 at full speed, and connect to the quad over a BT module on soft serial port 1 (RC ping 5+6). The problems I saw when trying to runt at 9600 are go...

For those who suffer seemingly inexplicable resets of serial port config when trying to change what ports do, for example like me who want to change port1 from doing everything (scenario 1) to only MSP (scenario 8) and let soft serial port 3 take care of CLI+MSP using scenario 5, with a bluetooth mo...

How reliable is the GPS parts of the firmware? I've just gotten a micro GPS unit for my 250 quad and I'd love to try it out, but I wouldn't want to suffer a flyaway, like I've heard some people using baseflight have suffered. Are there any gotcha's I should take care to avoid? I know making sure Mag...

I'm happy to report that changing my BT module's baud rate to 19200 and setting msp_baudrate in CLI to 115200 made it possible to use my OSD on serial 1 at full speed, and connect to the quad over a BT module on soft serial port 1 (RC ping 5+6). The problems I saw when trying to runt at 9600 are gon...

Next came another interesting issue. Since soft serial still doesn't work for me so I used my osd to tweak my settings. I raised yaw rate and lowered pid stuff to sensible values. Flew a battery and crashed violently after putting in a new one, I actually hit a parked car but no damage done thankfu...

After going into the code and reading up on the constraints around serial ports I figured out that what had caused my settings to be ignored/reset so many many times was that I had set port scenarios where CLI was enabled on more than one, for example scenario 5 on two ports. The documentation was c...

I was out doing flight testing today and it was not all smooth sailing. I tested auto tune and it seemed to work even though conditions were not perfect as there was a steady breeze. It ended up giving me unflyable pids as it turned out. I landed and accidentally saved the settings. I value was abou...

So far I've tried to get BT to work on soft serial as a proof of concept before I mess up my nicely configured OSD by reflashing it with a FW with a different baudrate. My gut feeling is that the OSD would become slow if the baudrate was dropped too low I've tried what feels like everything but the ...

I'll improve my issue report a bit. I've changed from a 2-pos switch to a slider, and if I got to the Aux-tab with the slider in low (1000-1200) it's showing LL as it should. As soon as it goes above 1200 it goes to L, above 1400 to M, above 1600 to H, so far so good. As soon as I go above 1800, HH ...

I've edited my question about soft serial and added the board type and RX setup. Hoping for some answers. I've set all my 8 channels endpoints in the DX18 to be so close to 1000 <--> 2000 as possible, and it's within +-10 on all of them. Here's the channel output, look at aux1 for example: https://d...

Issue report: Using the latest configurator and FW, I do get steps per channel in the configurator, but what's highlighted as current TX output and what's actually output doesn't really match. Example, on aux1 which is currently a 2 pos switch on my DX18 it says that for one endpoint that "two ...

Hi and thanks for the good work on cleanflight I've spent an evening trying to set up soft serial to do what I want, connect several serial devices with so far, no success at all. I've read all the documentation I'm able to find. This is what I'm trying to achieve: - Run a minimosd/kvosd on the stan...