Search found 1880 matches

by timecop
Wed Jun 24, 2015 12:51 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

12mil will hold 2A with 30C ambient temp and allowed 50C temperature rise. I have no idea what the stall current of HS81MG is, I see some spec saying operating current is ~250-280mA, so I guess you will be fine with this?
by timecop
Wed Jun 24, 2015 11:59 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

can someone please confirm the size of the SMD resistor array located between the input pads and the STM? I believe it's a 0603 size, but I'm not sure, don't have much experience with this particular SMD package size. The resistor array on one of my naze boards was damaged when I was trying to lay ...
by timecop
Wed Jun 24, 2015 11:55 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Hi fellow Naze32 users. Could someone tell me about how many Amps will hold original Naze32. I'll put FC into flying wing (maxi swift). I want to connect to FC: two digital servos (HITEC HS81MG), Rx (Rlink - 75ma@5v), GPS (RCTimer u-Blox CN-06 GPS Receiver V3.0) and MinimOSD v1.1 (m). Can I connect...
by timecop
Mon May 11, 2015 12:01 pm
Forum: Boards
Topic: Naze32 Afroflight rev5 motor 1 no output
Replies: 2
Views: 509

Re: Naze32 Afroflight rev5 motor 1 no output

Custom mix is probably the easiest solution unless you plan to recompile the firmware. The motor maps are in drv_pwm.c , under multiPPM or multiPWM arrays. I don't know why there's no output unless you touched it with 5v (or higher) while it wasn't powered and blew it out. I've actually done this be...
by timecop
Mon May 11, 2015 11:57 am
Forum: Software development
Topic: baseflight configurator (win/linux/mac)
Replies: 110
Views: 34417

Re: baseflight configurator (win/linux/mac)

Sounds like a lunix problem, permissions, etc? Make sure whaetver user is running Chrome can access ttyUSB0 or whatever.
by timecop
Fri Mar 13, 2015 3:52 am
Forum: Software development
Topic: Goggle Code is Shutting down.
Replies: 16
Views: 2711

Re: Goggle Code is Shutting down.

Maybe finally MultiWii will have an excuse to move to shithub, and start engaging in proper version control practices... :)
by timecop
Tue Nov 18, 2014 8:39 am
Forum: Software development
Topic: Call for robotic drone platforms for indoor commercial use
Replies: 10
Views: 738

Re: Call for robotic drone platforms for indoor commercial u

As with many other multi-rotor systems, the Inspire 1 relies on a GPS-based stabilization system that - thanks to spatial awareness - is able to hold a position even when experiencing wind interference, can compensate for overzealous pilot inputs to help avoid stalling, automatically brings the air...
by timecop
Mon Nov 17, 2014 8:18 am
Forum: Software
Topic: Wrong default mix for quadx and + on AfroMini32
Replies: 6
Views: 649

Re: Wrong default mix for quadx and + on AfroMini32

Yes, correct.
I think this is mentioned somewhere (or at least in afromini setup threads).

Because *default* purpose of afromini is for planes, so the servo/motor mapping is different.
and its SERVO_TILT
by timecop
Fri Nov 07, 2014 3:33 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

feel free to edit the documentation, it's on a wiki for a reason. unlike some other people (dominic "jobless" clifton), I do have a job that is a bit more important than having to document the same feature once in code and then once again elsewhere.
by timecop
Thu Nov 06, 2014 12:21 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

hwurzburg wrote:Not sure BF has GPS_SBAS_MODE clisetting....joblessflight does, however

protip, if you're not sure of something, not posting would be a better solution.
by timecop
Sun Nov 02, 2014 8:09 am
Forum: Boards
Topic: In-Flight Level Calibration -- Anyone Ever Use It?
Replies: 2
Views: 919

Re: In-Flight Level Calibration -- Anyone Ever Use It?

No, nobody uses that.
I doubt it even works.
It was something that was copied verbatim from multiwii, and probably didn't work there, either.
All it does is calibrate roll/pitch offsets for accelerometer, which you can do just as easy with acctrim.
by timecop
Mon Oct 27, 2014 10:38 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

there's some arm/disarm related stuff in cli.
set disarm_kill_switch
by timecop
Sun Oct 26, 2014 8:50 am
Forum: Software
Topic: Baseflight aka multiwii port to stm32
Replies: 1036
Views: 2289750

Re: GPS fix not being reported correctly in Config

Just put a UBLOX NEO-6M gps on my NAZE32 with cleanflight... In the Config GPS tab, its showing 7 sats indoors,and the correct LAT/LON...but the FIX is flashing alternatively on and off....the fix led on the GPS is blinking, indicating 3DFIX....and if I put the GPS on U-Center, it also shows 7 sats...
by timecop
Wed Oct 22, 2014 11:05 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Mag sensor defective?

Not sure if it works, but there was a recent addition "set mag_hardware = 0" scouring through the code, it looks like "3" disables. Again, I'm not sure if it works... Guess it should make the MAG turn red in Baseflight Configurator if it works. EDIT: Nevermind... option 3 looks ...
by timecop
Mon Oct 20, 2014 9:40 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

If I haven't bothered replying anyone's question here it generally means its so stupid I don't have time to waste explaining same shit that was covered a million times in the thread. If people can't be arsed to read the fucking manual and do basic shit like trimming their transmitter etc, there's no...
by timecop
Sun Oct 19, 2014 2:36 am
Forum: Boards
Topic: Need help, PC cant detect Naze32
Replies: 10
Views: 6306

Re: Need help, PC cant detect Naze32

uh, this has nothing to do with firmware. either shit cable as the guy above said, or USB socket isn't making good contact. If the board is getting power tho, the latter is quite unlikely.
by timecop
Sat Oct 18, 2014 4:39 pm
Forum: Boards
Topic: Need help, PC cant detect Naze32
Replies: 10
Views: 6306

Re: Need help, PC cant detect Naze32

uh, do you get USB plugin sound, do the leds blink alternating on startup.
by timecop
Sat Oct 18, 2014 5:10 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

I'm guessing just STM, but could be anything else. Usually I don't consider those repairable and just toss them.
by timecop
Sat Oct 18, 2014 5:08 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Mag sensor defective?

rev5 red board, latest firmware Previously I notice the mag sensor was acting erratic. The model image in the configurator would jump around and the raw sensor data for MAG would have drastic swings with the quad stationary. Now, there is no change in the MAG sensor data unless I bring a magnet clo...
by timecop
Sat Oct 18, 2014 5:04 am
Forum: Software development
Topic: GPS NAV
Replies: 964
Views: 168475

Re: GPS NAV

Feedback? Fork EZ-GUI and make your own version. It's the only way to go.
by timecop
Thu Oct 16, 2014 7:12 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

NG just means mixer isn't "sane" because you're missing 100% thrust on each axis due to missing motor. Anyway, it still allows flying so.
edit: once you copied the non-working motor pin, to regain mixer sanity, I think you can just replace the dead motor with 0/0/0 for RPY power.
by timecop
Thu Oct 16, 2014 2:08 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Hi, two of my Naze32 boards have a weird issue both with the 4th motor output, which doesn't send any signal to the esc while the other all other motors output work flawless. I tried everything, even resetting the board, but nothing helps. because it is the 4th pin I can't even use servo_flip to us...
by timecop
Thu Oct 16, 2014 2:03 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

jamieFL wrote:timecop,

You replied to this once before, but didn't answer my question...The photo is not my board but one I found on the net.

Naze32-Rev5---magic-smoke.jpg


BAT54C diode.
by timecop
Wed Oct 15, 2014 4:23 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Did you enable althold by default?
by timecop
Mon Oct 13, 2014 4:45 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Hi. I have a naze32 flashed with the latest firmware # version Afro32 CLI version 2.3 Oct 1 2014 / 07:45:46 If I power the board through usb, or a bec, and then power up my escs, all is well and everything works. HOWEVER. If I power the board and escs simultaneously, I only get the startup tone fro...
by timecop
Mon Oct 13, 2014 4:09 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

yea, pretty sure motor test just outputs in normal order. While mixer is different.
If it wasn't for years of retarded backwards compatibility, i'd say we should change mixer to use normal CW or CCW motor indexing without the dumb multiwii order. But too late now.
by timecop
Sun Oct 12, 2014 3:58 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

You need higher pitch/roll rates to flip on the spot. Also higher RC_Rate if you want, but pitch/roll rate is what will determine faster spin.

Not sure about yawing, load latest firmware? there was a yaw-related bug that was fixed months ago
by timecop
Sat Oct 11, 2014 7:05 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Maybe configurator bug? Not sure, I'm not actually sure what the problem/question is, try modifying the values through CLI and make sure you're running latest version configurator too (chrome->menu->extensions->update all)
by timecop
Fri Oct 10, 2014 7:49 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Have you bothered upgrading firmware?
Also, model won't move until green led is done blinking at power up.
by timecop
Fri Oct 10, 2014 5:49 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Do you see that crater on the STM32 mcu? It's gone.
Not worth fixing either - unless you want a mess of melted connectors.
by timecop
Thu Oct 09, 2014 8:13 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Hey how about you take javaflight discussion in the relevant thread, so people don't get confused of all the renamed variables? Thanks.
by timecop
Thu Oct 09, 2014 8:09 am
Forum: Boards
Topic: Naze32 / D4R-II / FLD-02 telemetry
Replies: 6
Views: 807

Re: Naze32 / D4R-II / FLD-02 telemetry

Ya that sounds like what you'd hookup to A1/A2 with a resistor divider already there.
by timecop
Thu Oct 09, 2014 12:31 am
Forum: Boards
Topic: Naze32 / D4R-II / FLD-02 telemetry
Replies: 6
Views: 807

Re: Naze32 / D4R-II / FLD-02 telemetry

Yes, you can use a voltage divider (2 resistors) and feed it into the A1 or A2 channels on your receiver (I think they're on that 4 pin connector that also has telemetry pin), and then configure the divider in FLD-02 screens, and set alarms on that.
by timecop
Thu Oct 09, 2014 12:29 am
Forum: Boards
Topic: Help! Motors going different speeds
Replies: 2
Views: 425

Re: Help! Motors going different speeds

Your RC is probably not centered at 1500.
by timecop
Wed Oct 08, 2014 3:42 am
Forum: Boards
Topic: Naze32 / D4R-II / FLD-02 telemetry
Replies: 6
Views: 807

Re: Naze32 / D4R-II / FLD-02 telemetry

For some dumb rason FLD02 doesn't allow seting alarms on FLVS pack voltage data (the stuff that we're sending from naze). It can only alarm on 'analog" voltage which is sent by receiver itself. So, without custom firmware (like opentx/taranis stuff) that receives FLVS voltage and alarms, you ar...
by timecop
Tue Oct 07, 2014 4:52 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

You can from 3S, you kinda can off 4S (Vreg max is 16V, absolute max 20V), so for 4S maybe you better stick a diode in series. Voltage doens't go to Vbat but directly to PWM pin (i.e the 5V motor connector center pins). Do keep in mind that if you are connecting 3S directly there, your receiver must...
by timecop
Tue Oct 07, 2014 4:49 pm
Forum: Boards
Topic: Naze32 - Are all boards prone to weird failures?!
Replies: 3
Views: 3905

Re: Naze32 - Are all boards prone to weird failures?!

Um dude, something is definitely broken and it's probably not the naze. Not sure what to tell you tho, I have D4R-II and lots of people use those, I haven't dicked with taranis receivers, sbut stuff should work out of the box but you need one of m to work. Anyway, all weird shit, can't happen, most ...
by timecop
Sun Oct 05, 2014 6:14 pm
Forum: Software
Topic: Baseflight aka multiwii port to stm32
Replies: 1036
Views: 2289750

Re: Baseflight aka multiwii port to stm32

In that long post I missed what it is that you actually did and what is it youre trying to do.
What is the "third serial port" checkbox?
by timecop
Sun Oct 05, 2014 6:12 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

It's gone, you plugged something backwards or fried it some other way. needs mcu replaced, not worth the effort (and all the melted headers)
by timecop
Sun Oct 05, 2014 5:23 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

triple check all props rotations/direction/connection order etc.
by timecop
Sun Oct 05, 2014 4:20 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

Well, its either -45 or +45, you can try both, after its connected, tilt the model front/back/left/right and watch 3d model in configurator, it should follow..
by timecop
Sat Oct 04, 2014 3:30 pm
Forum: Software development
Topic: New MSP command request
Replies: 7
Views: 931

Re: New MSP command request

baseflight already has a version string and extended MSP stuff. I'm all for blocking javaflight tho.
by timecop
Sat Oct 04, 2014 10:18 am
Forum: Software
Topic: Baseflight aka multiwii port to stm32
Replies: 1036
Views: 2289750

Re: Baseflight aka multiwii port to stm32

That part of the code wasn't touched.
by timecop
Sat Oct 04, 2014 10:17 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

No, you weren't missing anything.
Short them, plug in power, unshort. Bent paperclip or tweezers works best for it.
If you can't manage plugging in cable while they're shorted, keep the board/pads shorted and plug the opposite end of USB cable into PC/laptop/hub
by timecop
Fri Oct 03, 2014 11:50 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

FIrmware update has been covered a million times. Since you fucked it up, delete hercules, putty, stmflashloader, etc,
Short boot pins, check "no reboot sequence" in baseflight configurator, flash.
by timecop
Fri Oct 03, 2014 5:07 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

This has been covered in the thread before, even with pics of what needed to be added.
Pretty sure there's some forum thread and/or wiki entry somewhre on this too.
by timecop
Thu Oct 02, 2014 12:40 pm
Forum: Software
Topic: Baseflight aka multiwii port to stm32
Replies: 1036
Views: 2289750

Re: Baseflight aka multiwii port to stm32

wut
are you doing this on some homemade board where gyro isn't in standard orientation?
by timecop
Wed Oct 01, 2014 3:37 am
Forum: Software
Topic: Baseflight aka multiwii port to stm32
Replies: 1036
Views: 2289750

Re: Baseflight aka multiwii port to stm32

Telemetry has been fixed - new binary is up. Thanks for testing, guys.
by timecop
Wed Oct 01, 2014 3:36 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 619805

Re: Naze32 hardware discussion thread

No, there's 2 separate 3V rails - but what you could do is just give it ~3.xV to begin with (instead of 5),, and the regulators will just work in dropout mode without regulating anything.. All the stuff on board will actually run down to 2.8V? I believe so even 3V output is fine.
by timecop
Wed Oct 01, 2014 12:38 am
Forum: Software development
Topic: Why development has stopped?
Replies: 230
Views: 19767

Re: Why development has stopped?

Anyway, back on thread, the issue IMHO is not with board availability but with the lack of high-quality, accessible firmware to put on them. You've pretty much nailed it. Also lack of people interested in writing non-shitty code and improving one thing instead of renaming shit everywhere and wastin...