MultiWii

Hello, I'm trying to use Frsky Telemetry on my CC3d and D4R-II. To which output of the CC3Dd do I connect the D4R Telemetry-RX? Am I right assuming it's Pin 4 of the RC_Input port? And then: What Data is available out of the Box, i.e. without any Hardware? Lastly: Can I connect 7 Battery Voltage sen...

Hello, i don't know what code you are referring two, and i guess noone wants to search the whole thread to find the correct link. maybe you should post it. Sorry. This is the Code I refered to: http://www.multiwii.com/forum/viewtopic.php?f=7&t=1929&start=150#p43296 http://www.multiwii.com/fo...

Hello Alex, I' exited to see the progress. Thanks, I appreciate your work on MultiWii! There is some code for FrSky Telemetry. Is there a chance that it can find its way into 2.4? Here's the code for 2.3: http://www.multiwii.com/forum/viewtopic.php?f=7&t=1929&start=150#p43296 Here's the docu...

No comments?

Hello, can someone confirm, that this code (FrskyTelemetry.zip 3344Byte) works with an X8R? There were comments in this thread, that the X8R uses a different SPort Protocol (which sounds odd to me: Does FRSKY offer different Sensors for it?) Besides: I use this inverter: m Unfortunately it gets very...

Hello,

thanks for the work on this!
Can you confirm, that this is the latest code?
http://code.google.com/p/multiwii-osd/s ... rsky_sport

And:
What's that about the S.Bus Host Mode?
https://code.google.com/p/multiwii-osd/wiki/Frsky_SPort
What's the difference?

Greetings,
Hendrik

Hello,

can someone tell me, why the code for this is not part of the GIT?

Greetings,
Hendrik

Hmmm, I fear my post was too long?

Hello, I am using/starting to use a Flyduino Mega and a Frsky Taranis with the X8D, which supports Telemetry via SBUS. Now, browsing through EZ-Gui, I noticed the FrSky Telemetry-Option. Searching about what's behind this, I found this thread and read most of it. The general process is understood: C...

Thanks.
Then, I will probably move the IMU up, because I think the Current is influencing the MAG.

Greetings,
Hendrik

henfri wrote:can someone report a working WIFI<->Serial Adapter?

Is noone using Wifi to connect?

Greetings,
Hendrik

Noone?

Hello, I am using the FMP04 connected via Serial2 to my Flyduino. I am now a bit uncertain, what Firmware to flash. In config.h it says: // avoid using 115200 baud because with 16MHz arduino the 115200 baudrate have more than 2% speed error (57600 have 0.8% error) #define GPS_BAUD 38400 On the other...

Hello,

can someone report a working WIFI<->Serial Adapter?

Regards,
Hendrik

Hi Waltr, sorry for not describing. The motors changed speeds rapidly and apparantly in a chaotic manner. I found the reason though: The 10DOF module was turned 180° around, i.e. the pitch axis was wrong. By the way: I read that the Gyro should be at the c.g. With the flight-battery below the quad, ...

Hello, I am almost ready to fly (well, I think I was with my first Quadrocopter (Flyduino MEGA, Drotek 10DOF, Align RCE BL35x). I get the sensors calibrated and the Quad on the Gui follows the motion of the actual Quad. When I arm the Quad, the motors go to idle speed. But as soon as I go beyond idl...

Hello, I have an FMP04 that I bought used. Thus, I don't know whether it is flashed to 5Mhz/10Mhz and to what baudrate. I use a Flyduino Mega and a Flyduino Break Out Board for the GPS. Unfortunately, with all three Baud-Rates (9600, 38400, 115200) the MultiWiiConf does not show me a GPS Fix -I am i...