MultiWii

Hahahhaa ok. Ill try again.
Flashed 10.02.2014 firmware on Naze32 rev5.

Softserial enabled. Now I cant connect via usb or reflash to get rid of the setting anymore.

Any ideas?

Ok. These specific steps has blocked me from connecting to my naze32. 1. Install latest (october release) of Baseflight. 2. Start re set all settings. 3. Tick the "Third serial port" checkbox on the new tab page and hit save. Now I can not connect with USB any more. I have tried to reflash...

Seems like the cables and settings and everything were set up properly. Not sure why it didnt work yesterday. When I when out and flew during lunch today, suddenly the gps coordinates and everything just appeared on my osd. Flew 2 batteries worth of 20 mins and no problems. Now I just have to take m...

Hey guys! I have hobbykings ublox lea6h gps. I have configured it in ucentral and now its reacting really good. As soon as I plug it into a usb-port, it aquires a lock and flashes blue within a few seconds. But ... when I try to connect it to the naze the led do not flash blue. Baseflight says that ...

With your setup if you waggled your sticks hard enough you'd get the same effect since that is all the autotune code is doing - except that it records some data and performs calculations too. Just curious how long you think you were testing autotune before you had the problems? Haha, yes. I am sure...

Conclusion: Do NOT try autotune on this setup. I am now three expensive engines poorer because of it... An FC should not be able to fry a motor if esc/motors are dimensioned correctly. I agree. If the signals going to the ESC are causing the motors to fry, then the ESC is at fault; it shouldn't all...

Edit: Added that the battery is 4s. This is very likely the root of the problem as the motors are specified for 3s. Ok. Bad news about autotune. Here is my setup: * Full naze32 rev5 with Cleanflight/NAZE Sep 6 2014 / 00:24:11 (ca72890) * Blackout spider hex (hex6x mixer) * T-motor mn1806 2300kv * Hq...

Thanks! I will try it out! Any idea on which parameters that might have to be changed? Ps. One of my motors finally gave up today before I had a chance to try autotune. Will switch it today and try the autotune tomorrow. Ill report back when it is done. I used this tutorial and satellite data showed...

Any idea on which parameters that might have to be changed?

Ps. One of my motors finally gave up today before I had a chance to try autotune. Will switch it today and try the autotune tomorrow. Ill report back when it is done.

Im going to test autotune later today, Ill report my results here tonight. Anyways, on to my issue. I have my ublox lea-6h gps connected, but even though I think I have everything setup correctly in the cli, the gps still wont see any satellites. Any ideas on what may be wrong? I am running full naz...

Just change your 'reboot_char' (or something smilar, do 'set reboot' or 'set reset' from 'R" to something else, like Z or some other character. ...Sorry, Im a bit of a n00b here. Is it something I can do from the cli interface? Or do I have to edit some config.h file or anything similar in the...

timecop wrote:Something is sending 'R' to your hardware when you plug it in.

Hmm ... Ill connect the osd to an arduino and check serial output. It will be a few days until I have time to do this though. Ill get back on the issue....

I can't see how those rubber nipples would go any way towards reducing vibration, but if it works it works. I noticed the drift in acro mode after a quick flip, or doing the following: Fast forward flight, then give a hard yaw through 180 degrees so that it's flying backwards. The craft would alway...

Firmware version: Afro32 CLI version 2.2 Aug 3 2014 / 21:51:54 Board: full naze32 I guess I was a bit unclear. Running with OSD and plugging in USB is two separate scenarios Scenario 1: Osd _NOT_ plugged into serial pins. Trying to connect with usb lights up all leds and then this happens: 21:00:26 ...

marcelokron wrote:Hey mate, do you have some photos just to check how you made it?
Thank you!!

Sure!


Full rubber niplet between board and spacer. Small rubber ring (half a niplet) on bottom between spacer and body.

A weird problem started happening a few days ago. Whenever I plug in the usb and press connect in the chrome baseflight application, all leds light up indicating bootloader mode and I cant connect. A similar thing happens when I have my multiwii osd (minimosd) connected to rx when I plug in the batt...

Just wanted to say that good vibration dampening fixed the issue for me. See separate thread here: http://www.multiwii.com/forum/viewtopic.php?f=22&t=5470#p55522 Now I can flip all I want, no problem! 2. In angle, when recovering out of a fast run, the hexa doesn't level correctly. I fly in Angl...

It was the vibrations that were causing it. I got the vibration dampeners this week, so I padded the naze with them and went out end flew really agressivly. Like 4 batteries of only hard turns, flips and rolls. No more drift. Before I got drift after every single flip. So problem solved So the concl...

Ok, I can now confirm that I still have the same problem, even with the new firmware.

The rubber vibration dampers should show up on friday or early next week. Ill report back to see if they fix the issue.

Ok ... I flashed firmware. Now it says:

Afro32 CLI version 2.2 Aug 3 2014 / 21:51:54

Is this the latest version? Should this work? Im going to try it out tonight or tomorrow, as soon as I get some time on my hands.

timecop wrote:So, upgrade firmware.

Oh. Thats embarrassing... I looked at the date 1 June 2014 and thought I had the latest firmware.

Well, thanks for the help anyways everyone.

need actual version reported by "version" from CLI This is from the log topside: 22:31:57 -- Running - OS: MacOS, Chrome: 36.0.1985.143, Configurator: 0.49 22:31:59 -- Serial port successfully opened with ID: 1 22:31:59 -- Unique device ID received 22:31:59 -- Firmware Version: 2.3 And he...

I have not changed any parameters regarding the accelerometer. Just calibrated. I am using stock baseflight with firmware version 2.3. I have ordered some vibration dampeners to mount the board on. Ill see if that makes a difference. It will take a week or so for them to arrive. Then I will report b...

BarneyG wrote:Interesting ... this was a bug in multiwii 2.2 But I thought it was fixed in 2.3 which is what the current Baseflight is based on.

I just had to double check after I read this. But it the configuration tool do say Firmware 2.3. The card is a full naze32 in hex6x mode.

2. In angle, when recovering out of a fast run, the hexa doesn't level correctly. I fly in Angle mode so that is my main issue. A couple of things that I've checked: CoG is correct and well balanced, subtrims are good (1500), all motors/ESC's are brand new and work as expected in baseflight motor t...

I have a full naze32 rev5 board running firmware 2.3. Like the title says, if I fly aggressively in angle or horizon mode and do a hard turn, it seems like the accelerometer gets offset and the hexacopter starts to drift. After som flips I did today, the drift was quite alot. When this happens, I ha...