Search found 7 matches

by cherokee180c
Wed Aug 20, 2014 3:10 am
Forum: Software
Topic: Airplane RTH BaseFlight
Replies: 143
Views: 136489

Re: Airplane RTH BaseFlight

Thanks again. I learned a ton tonight and was able to flash your hex file into the flip32+. I also enabled mixer airplane and saw how to set up the additional ailerons. I also decided it was best from a physical and programming standpoint to just buy the SBUS to CPPM converter for the FrSky X8R, so ...
by cherokee180c
Tue Aug 19, 2014 10:56 pm
Forum: Software
Topic: Airplane RTH BaseFlight
Replies: 143
Views: 136489

Re: Airplane RTH BaseFlight

The regular Baseflight works only as a flight stabilizer. For RTH function on a plane you need to use my modified version. Separate L/R ailerons is supported. If you use a Arduino board you can even setup Crowbreaks and flaperons in the controller.(Removed in BF) You can set up Passthru on a AUX ch...
by cherokee180c
Fri Aug 15, 2014 5:06 am
Forum: Software
Topic: Airplane RTH BaseFlight
Replies: 143
Views: 136489

Re: Airplane RTH BaseFlight

I already have an AcroNaze 32 board and a full Naze 32 board that I am familiar with for quads. What would I need to do as far as firmware to use for a glider? Does the normal baseflight program have the code or do I need to flash with new hex? Also, can the Naze handle separate L/R aileron channels...
by cherokee180c
Tue Jul 22, 2014 11:37 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380620

Re: Naze32 hardware discussion thread

AvengerIl wrote:


for pin 6 i believe you need;
set telemetry_port = 1
ref;
https://github.com/multiwii/baseflight/wiki/Telemetry[/quote]

Thanks, I actually have it working fine using soft serial but I can't get working on the fr sky pins!
by cherokee180c
Tue Jul 22, 2014 1:41 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380620

Re: Naze32 hardware discussion thread

I have the telemetry to a Taranis on a D4R-II in PPM mode working perfectly to give me pack voltage via soft serial, however, I can not get working at all on the Fr Sky pins. I have followed the wiki exactly and tried multiple times. I need to get it working on the Fr Sky pins to free up pin 6 using...
by cherokee180c
Wed Jul 16, 2014 11:23 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380620

Re: Naze32 hardware discussion thread

PID tuning has nothing to do with the variables you quote. Do some reading on the effects of each. There are plenty of sources and even videos on youtube for quads. In general if you are getting too much correction, lower the P value and until corrections are smoother. Then you may need to raise the...
by cherokee180c
Wed Jul 16, 2014 2:33 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380620

Re: Naze32 hardware discussion thread

I am trying to troubleshoot a problem with the AcroNaze32 telemetry connection to a Taranis running the new OpenTx 2.0.5 and a D4R-II reciever. I am trying to get pack voltage through the telemetry. Here is a summary of my status: PPM enabled, Vbat enabled, Telemetry enabled, Telemetry_provider=0, T...