MultiWii

Hello I tried to follow the above instructions but I didn’t succeed! Problem with is 1000 – 15000 – 2000 I am using: TX: FlySky Upgraded 2.4G 9CH RX: FS-R8B MWC MultiWii SE V3.0 I uploaded the newest Conf.h I think V 2.3 I can set up the middle to 1500 but then min is 1062 and max is 1963 if I chang...

Salamala, You're running a 2S battery. I would use a smaller capacity, but higher cell count battery. ie the very popular 3S 2200 mA battery would work very well with your setup. 2S will really struggle to get that frame off the ground. With 3S it should perform well. Nebbian you are killing me!! I...

"R" stands for right hand rotation. Make sure you actually have the right props, otherwise the setup should be fine. Hi Arakon, you are like may personal angel! Buddy thanks for all what you don up to now for me! Ok now lest end sucking up! Can you elaborate a little on "right props&...

Please help, Finally today I got ma batter and went to fly my new quad and what a disappointment that was. Any way let me start with the setup Total weight 921g Motors 4X930Kv ESC 4x 30A Props 1045R CW CCW newer figured out what “R" sands for Battery: 2S 20C 3000mah (full) FC: MWC MultiWii SE V...

Arakon THANKS!!!!!
One question more
How do I connect it to my FC
As it sees
6P cable for GPS
4P cable for compass

Thanks!

Arakon thanks for fast replay So what you say that on this board I can use 1. http://www.banggood.com/Electronic-Compass-Module-Three-Axis-Magneto-Resistive-Sensor-p-926151.html http://imgmgr.banggood.com/images/upload/2014/05/SKU135383/bg/SKU135383g.jpg 2. http://www.banggood.com/GY-NEO6MV2-Flight-...

Hi to all first So I have MWC MultiWii SE V3.0 and I would like to connect to it a GPS I am novice so I am little confused Let me put some schematics of the board itself: http://img.hobbywow.com/41271_0.jpeg http://s4e3c56b671b69.img.gostorego.com/809E82/cdn/media/s4/e3/c5/6b/67/1b/69/catalog/produc...

fuh thanks for everything
After sending details the seller agreed to send me e new one so I think it is a board fault.
Will post after receiving the new one!

1) Well I don’t know why I uploaded the FC started blinking left it for 2 min returned AUX 1 still works that was strange to me. It did change other settings like mintrothel etc. 2. didn’t really understand this (sorry) and the battery is 2S not 3S ESC is not flashed (didn’t get to that part yet) ES...

fuh you are really helpful and many thanks for you effort. One of ESC calibration was done with connecting to RX Now let me ask you few thing and pleas if you can answer me. 1. When I do EEPROM flash is it normal that the FC keeps arming on aux1 (I ask because I thought it sets up everything to begg...

Fuh if you ever come to Croatia you have a drink from me Yes I know about LED flashing (in my case green) The voltage 5.05V was measured on free pins of FC also last night I measured it on each ESC (disconnected) + 5-5.5V Signal cca 4,7V. I didn’t configure fail safe mode but if it was it I think th...

Fuh I did the "calibrated the ESC with the no fly option" as I did the RX ESC calibration and thy work fine when connected to USB the single beep happens only when connected without USB, Also don the GUI setup then normal aurdiono and in the end EEPROM. The only thing after doing EEPROM I ...

fuh thanks for fast replay, I use ESC bec and as I mentioned I tried with each one separately so in more than one occasion (4 to be exact) only one + line form ESC was connected to FC. Also I set up “arming” on aux 1 so it’s easier and not confusing P.S. A even flashed config.h thinking that would h...

Hello I checked even connected each ESC separately, I didn’t get any documentation with the FC so I don’t know did I connect everything ok so I am posting a picture to show you. Also I supplied RX throe FC and separately (the picture is separately situation) Please help! http://oi57.tinypic.com/30k3...

Yes over ESC BEC and I measured it wit multimeter it s 5.05V. Also the red LED starts up bright but when I connect the TX-RX the led loses on brightness (also powered the RX separately not using ESC BEC and FC)

Hello I have MWC MultiWii SE V3.0 The board can be armed only when connected to USB - PC if it is not connected to PC it cannot be armed and the green light don’t come up. I measured the voltage on BEC ant it is 5.05V which is sufficient. So basically the board is useless (except if I fly may quad w...