Search found 11 matches
- Fri Aug 15, 2014 7:47 pm
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
Re: CJMCU microquad board
YYEEAAAH!!! I SAW IT FLY!!! A bit strange behavior - at some throttle position begin to vibrate braces. Tried 3 times, the central plate remains stationary, two braces begin to vibrate, and then added a third. Can somebody share PIDs here? Thanks a lot for a help, guys. I was hoping in the depth of...
- Fri Aug 15, 2014 5:26 pm
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
Re: CJMCU microquad board
Thanks goebish, something seems to move. But... Stick positions in configurator are different from reality, and can't arming as before. Does exist some mode to calibrate Rx? Sorry for a stupid question...
PS in dump find nothing...
PS in dump find nothing...
- Fri Aug 15, 2014 2:15 pm
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
Re: CJMCU microquad board
My experience with CLI is lower than zero... I was able to change channel map to ERTA (mode1) and save it, but can't change rx type.
- Fri Aug 15, 2014 11:54 am
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
Re: CJMCU microquad board
Hi guys. It's frustrately enought, but my quad continues to remain on the ground. I've tried both firmware, from mj666 and dominicclifton, both flash on OK, baseflight configurator see a quad,... But I can not make arming. I've tried two receivers, spectrum AR6200 satellite connected SER to PA3 and ...
- Wed Jun 11, 2014 2:15 pm
- Forum: Boards
- Topic: ARM Cortex-M3 STM32F103C8T6 STM32
- Replies: 37
- Views: 18353
Re: ARM Cortex-M3 STM32F103C8T6 STM32
e_lm_70 wrote:Keep it as it is the P2 = with the jumper on
Does it mean that I can desolder pins and short pads permanently?
- Tue Jun 10, 2014 5:28 pm
- Forum: Boards
- Topic: ARM Cortex-M3 STM32F103C8T6 STM32
- Replies: 37
- Views: 18353
Re: ARM Cortex-M3 STM32F103C8T6 STM32
And P2 jumper?
- Tue Jun 10, 2014 3:14 pm
- Forum: Boards
- Topic: ARM Cortex-M3 STM32F103C8T6 STM32
- Replies: 37
- Views: 18353
Re: ARM Cortex-M3 STM32F103C8T6 STM32
Guys, I know silly question, but I'm confused in the position of jumpers to flashing firmware. I've try something like thishttp://gekogeek.com/embedded/flashing-programs-to-stm32-embedded-bootloader/, but PC don't see target. Can anyone explain here step by step how to flash?
- Mon Jun 09, 2014 6:46 pm
- Forum: Boards
- Topic: ARM Cortex-M3 STM32F103C8T6 STM32
- Replies: 37
- Views: 18353
Re: ARM Cortex-M3 STM32F103C8T6 STM32
Danke, Mann
- Mon Jun 09, 2014 4:08 pm
- Forum: Boards
- Topic: ARM Cortex-M3 STM32F103C8T6 STM32
- Replies: 37
- Views: 18353
Re: ARM Cortex-M3 STM32F103C8T6 STM32
I have a couple of these. Pretty cheap. m 64 pin variant. Gives better access to the third hardware serial port without sacrificing other pins. I still prefer the 48 pin footprint for compactness but for dev this is pretty cheap and works. Have gps, stlink/v2 debugging, gy-86 sensory board, status ...
- Sun Jun 01, 2014 5:38 am
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
Re: CJMCU microquad board
Thanks, TC, I'll try
- Sat May 31, 2014 9:37 am
- Forum: Boards
- Topic: CJMCU microquad board
- Replies: 161
- Views: 115176
CJMCU microquad board
Hi to everyone. I hope to find here STM32 experts who want to ask for advice. Some days ago I receive this board. DSCF9659.jpg DSCF9667.jpg DSCF9660.jpg By the labeling, I can not understand how to connect the receiver. The seller have no information. The board has a lot of pads, but they are labele...