Search found 21 matches

by nechaus
Sun Nov 09, 2014 1:22 am
Forum: General discussions
Topic: Release multiwii 2.4
Replies: 3
Views: 1253

Re: Release multiwii 2.4

Doesn't have all the features in it. Been using the development versions since they were released... There is a nasty bug with the baro navigation b7
by nechaus
Tue Oct 28, 2014 12:52 am
Forum: MultiWii tweaking - flying experience
Topic: New Y6 is twitching.
Replies: 7
Views: 1569

Re: New Y6 is twitching.

whats the measured current draw?
by nechaus
Wed Oct 22, 2014 1:33 am
Forum: General discussions
Topic: Release multiwii 2.4
Replies: 3
Views: 1253

Re: Release multiwii 2.4

+ 1 here.

should just release the beta, I am keen to try it.
by nechaus
Tue Oct 21, 2014 9:42 am
Forum: MultiWii tweaking - flying experience
Topic: can multiwii fly like a DJI?
Replies: 5
Views: 1643

Re: can multiwii fly like a DJI?

if your gps hold is working good, you can dynamically update the gps hold position by enabling AP FLIGHTMODE But this is only another way of using gps hold.. But what you speak of can be done with ardupilot.. I have used hex's on loiter mode/gps hold, and it holds the position incredibly well, from ...
by nechaus
Thu Oct 16, 2014 1:43 am
Forum: FPV, OSD, Cameras
Topic: Mobius HD Camera
Replies: 14
Views: 4042

Re: Mobius HD Camera

Mobius is good, but the quality is no where near the same as my gopro's 3+ I have a gopro hero 2 gopro hero 3+ black and gopro hero 4 black.. The mobius is similar to the hero 2.. But the hero 3 and 4 black edition just shit all over the mobius... The hero 3 and 4 black is so sooo much more clearer,...
by nechaus
Tue Oct 14, 2014 1:38 pm
Forum: General discussions
Topic: [CRITICAL] MultiWii jam condition
Replies: 11
Views: 1341

Re: [CRITICAL] MultiWii jam condition

sounds like it could be your wiring or something.. try run fc from a good known ps Id be checking voltages of your becs and running though the whole thing with a magnifying glass. you really need to diagnose this and not guess and only fly it once you know what went wrong. I will not fly a quadcopte...
by nechaus
Tue Oct 14, 2014 1:07 pm
Forum: MultiWii tweaking - flying experience
Topic: RTH Solid. GPS Hold Super Wonky?
Replies: 1
Views: 636

Re: RTH Solid. GPS Hold Super Wonky?

calibrate your baros PIDS.. get altitude hold working first..
then start tuning gps hold...
by nechaus
Tue Oct 14, 2014 1:03 pm
Forum: Frames
Topic: HK Talon.
Replies: 5
Views: 3401

Re: HK Talon.

I don't think its the crappy aluminium... its more the design... If you have access to a 3d printer, you can make some better motor mounts which cover more surface area on the arms.. Even on my big tarot hex, After a crash i need to double check the motor mounts to make sure they are still aligned.....
by nechaus
Tue Oct 14, 2014 12:59 pm
Forum: Frames
Topic: VTAIL configuration
Replies: 2
Views: 2276

Re: VTAIL configuration

I am currently printing a 4 minute design via cad lol..

have you tested different angles? I was going to test a punch tomorrow... But do you have any idea which is the most efficient ?
by nechaus
Sat Oct 11, 2014 2:16 pm
Forum: General discussions
Topic: I just lost my second quad
Replies: 16
Views: 2215

Re: I just lost my second quad

There is a bug in the navi b7 beta with the baro not turning off.. But man.. you have to expect this to happen.. I feel safe using my mini quads around the suburbs.. and I use my big 450mm + when @ fields, I use extremely over powered machines that break frames, props, bearings, batteries, ego.. Its...
by nechaus
Thu Oct 02, 2014 1:24 am
Forum: MultiWii tweaking - flying experience
Topic: Servo gimbal travel scaling questions
Replies: 3
Views: 768

Re: Servo gimbal travel scaling questions

I adjust this via the multiwii ezy gui app
by nechaus
Thu Sep 25, 2014 3:56 am
Forum: MultiWii tweaking - flying experience
Topic: PID tuning position hold
Replies: 14
Views: 6310

Re: PID tuning position hold

while i remember, there are apps on android and probably ios to test the magnetics interference to give you a visual reference.. you can use your phone and place it near the fc and power it up and see how it responds
by nechaus
Thu Sep 25, 2014 3:53 am
Forum: MultiWii tweaking - flying experience
Topic: PID tuning position hold
Replies: 14
Views: 6310

Re: PID tuning position hold

Guys, Your issue maybe the mag getting magnetic interference from your power cables.. I am not sayng this is your issue but its worth while keeping in mind.. I had this issue where I was getting gps lock, looked all good, but it had similar behaviour to NEROX... PIDS certainly did change the behavio...
by nechaus
Mon Sep 22, 2014 1:33 am
Forum: Getting Started - MultiWii config and setup
Topic: New project, nearly no experience
Replies: 3
Views: 445

Re: New project, nearly no experience

never use the software that the board comes with.....
always compile new firmware ..
by nechaus
Thu Aug 21, 2014 7:33 am
Forum: General discussions
Topic: Leaving multiwii
Replies: 1
Views: 499

Leaving multiwii

Well I am a bit over using multiwii, used it for the best part of two years, I was hoping for further development but it just takes to much time. I have switched APM, putting MPNG on all my boards and getting some new pixhawk gear. I love how simple multiwii is, but it really lacked fail safe featur...
by nechaus
Wed Jun 25, 2014 1:56 pm
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 297025

Re: MultiWii EZ-GUI

I can confirm the problem,
After troubleshooting the bluetooth module was damaged in a crash. Took me some time to figure it out as i was using the bluetooth less on those particular days.

So multiwii app is still pro! thanks. sorry for wasting time
by nechaus
Tue Jun 24, 2014 12:31 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 297025

Re: MultiWii EZ-GUI

Everything was working. connecting, setting way points, doing it all.. Today I am getting no data received error. can i delete and reinstall the app since i paid for it?? and it will be unlocked again? I cant seem to figure this out, nothings change, no hardware or software.. it just does not want t...
by nechaus
Wed Jun 11, 2014 9:23 am
Forum: MultiWii tweaking - flying experience
Topic: Multiwii 2.2 GPS question and PID's
Replies: 9
Views: 3586

Re: Multiwii 2.2 GPS question and PID's

just to check, you have added mag dec ?
by nechaus
Tue Jun 03, 2014 1:25 pm
Forum: General discussions
Topic: are there issues with the HK 328P ?
Replies: 3
Views: 640

Re: are there issues with the HK 328P ?

I'm good now on my 4th build. . Got apm going .
I flashed my escs with simonk
by nechaus
Wed May 14, 2014 12:18 am
Forum: Frames
Topic: X525 antivibration mount reqd? PID tuning for frame
Replies: 2
Views: 5625

Re: X525 antivibration mount reqd? PID tuning for frame

did you test the motors independently ? its possible to of created a small short with one of the phases causing terrible motor performance... you should check all motors out... I went through something similar and it was driving me nuts... found out 2 of my 4 motors are junk... phase connection seem...
by nechaus
Wed May 14, 2014 12:13 am
Forum: General discussions
Topic: are there issues with the HK 328P ?
Replies: 3
Views: 640

Re: are there issues with the HK 328P ?

I just got one... I found if you don't calibrate the magnometer it will flip off the bat... another thing... I was using cheap motors... I added lpf filers on smoothed it right out... but I never got to properly test mine.. will report back in a few days.. I hope this board is good.. saw some great ...