Search found 8 matches

by paddytfm
Thu Sep 05, 2013 10:11 pm
Forum: ESCs, propellers , servos and radios
Topic: Simonk ESC vs standard (my opinion)
Replies: 14
Views: 3295

Re: Simonk ESC vs standard (my opinion)

Thank's for answer and any help
I'll try to calibrate each time i load a new upgrade.
Paddytfm
by paddytfm
Wed Sep 04, 2013 10:19 pm
Forum: ESCs, propellers , servos and radios
Topic: Simonk ESC vs standard (my opinion)
Replies: 14
Views: 3295

Re: Simonk ESC vs standard (my opinion)

Has anyone observe lost of calibration on ESC after time. It can happen at anytime and of course when you want to fly far away home. The fact is the first couple ESC & motor the upper left esc on our quadx does not start at all. I have changed the ESC and motor but same result. My setting are 10...
by paddytfm
Sat Oct 20, 2012 11:58 am
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 41576

Re: Inflight ACC-calibration

hi.you don't do the combo inflight o_O. you switch of aux arm while flying. and the code saves the offset after landing. so aux arm or passthru is needed. Hi nils You say : you switch of aux arm while flying. I understand , In flight calibration procedure: AUX OFF is default position Start flying AU...
by paddytfm
Fri Oct 19, 2012 9:20 pm
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 41576

Re: Inflight ACC-calibration

Hi, and thank's for reply.
Right, need timing , less than 1 seconde would be nice.Stick combo does destabilisation of the device in flight. When i say Channel I mean Aux1. What else.
Paddytfm
by paddytfm
Thu Oct 18, 2012 9:31 pm
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 41576

Re: Inflight ACC-calibration

HI everybody I have a proposition to do for inflight calibration with The 5th channel used as level mode switch. If in or while normal mode do a short time toggle switch in level mode and back to normal mode. If in or while level mode do a short time toggle switch in normal mode and back to level mo...
by paddytfm
Wed Aug 24, 2011 10:30 pm
Forum: Getting Started - MultiWii config and setup
Topic: Compile MultiWiiConf-Basic HowTo
Replies: 16
Views: 15805

Re: Compile MultiWiiConf-Basic HowTo

Thank's for the post, particularly Gompf for explanations and patrike for the upgrade So in order to see Yaw Z axis working like other axis in the graph I did this // if (azGraph) { // if (scaleSlider.value()<2) g_graph.drawLine(accYAW, -1000, +1000); // else g_graph.drawLine(accYAW, 200*scaleSlider...
by paddytfm
Mon Aug 08, 2011 10:21 pm
Forum: Software development
Topic: v1.8
Replies: 69
Views: 13487

Re: v1.8

Hi everybody About reversing direction of sensor, changing sign of the proper axis , acc or gyro works fine. // Assemble 14bit data gyroADC[ROLL] = - ( ((rawADC[5]>>2)<<8) | rawADC[2] ); //range: +/- 8192 gyroADC[PITCH] = - ( ((rawADC[4]>>2)<<8) | rawADC[1] ); gyroADC[YAW] = - ( ((rawADC[3]>>2)<<8) ...
by paddytfm
Sun Aug 07, 2011 9:15 pm
Forum: Software development
Topic: v1.8
Replies: 69
Views: 13487

Re: v1.8

Hi
I confirm Roll Acc_orientation as no effect compare to MultiWii_quadrino_20110725 previous version.
Waiting for a release.
Regards
Paddytfm