Search found 9 matches
- Mon Nov 17, 2014 2:34 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
see if set gimbal_flags=4 does what you want. "When feature SERVO_TILT is enabled, this can be a combination of the following numbers: 1=normal gimbal (default), 2=tiltmix gimbal, 4=in PPM (or SERIALRX) input mode, this will forward AUX1..4 RC inputs to PWM5..8 pins" when I used this I did...
- Mon Oct 20, 2014 8:34 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Actually it was a google search that led me here but understood.
- Mon Oct 20, 2014 3:58 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Timecop I Have read the manual (both revisions). However from watching a few setup videos one gets the impression that the default settings are fine for flying thus the confusion. I just want to make sure the fault is mine not the boards. I'm very new here and just trying to help but I have a coupl...
- Sun Oct 19, 2014 6:51 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
I have one out of three boards doing this. And mainly under power. Recently, it has been impossible to perform a proper calibration on the one mini as it reboots when the battery is plugged in. Seems to cause the escs to go into program mode. Now that I'm mentioning it here, I'll give it another go...
- Sun Apr 27, 2014 4:33 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Wow that's great. I didn't realize as I thought I read a post from timecop that these weren't supported but maybe an old post.
- Sun Apr 27, 2014 3:36 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
What supported features would require GPS? is there a RTH or position hold?
- Fri Apr 25, 2014 3:53 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Last night I ordered two Naze32's (full sensor). So let the journey begin.
- Fri Apr 25, 2014 1:06 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Thanks Olddude. I'll dive into the manual and start working through the thread. If anyone else has suggestions please post. And I might be interested in a case. What colors are available? Are the white translucent enough to show the status leds?
- Thu Apr 24, 2014 9:22 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1416596
Re: Naze32 hardware discussion thread
Hey I'm new here and looking forward to learning about Naze32. I'm going to apologize in advance for asking some new guy questions but to be honest I'm a little overwhelmed as to where to start. First let me tell you about my experience. I've built about 8 or 9 multirotors and except for my very fir...