Search found 17 matches

by FedorCommander
Tue Mar 31, 2015 11:40 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

To compile its not an issue at all.. All nicely described at leant on cleanflight site. Took me 15 minutes to get HEX on mac. Kinda nice. Just curious. Is this possible to make custom mix, lets say for 6 motors, which will have 2 motors "useless" ? Of course those 2 motors will be on rippe...
by FedorCommander
Mon Mar 30, 2015 9:30 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

And solder it back no option?
by FedorCommander
Sun Mar 29, 2015 10:53 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Yap. Something strange going on.
by FedorCommander
Sat Mar 28, 2015 7:25 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Can you CONNECT and CONFIGURE over ftdi?
by FedorCommander
Sat Mar 28, 2015 10:06 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

So if all works fine over ftdi - you can keep configuring it over ftdi while powering from servo connector. Right? BASE/CLEAN flight should work over ftdi just fine.
by FedorCommander
Fri Mar 27, 2015 11:20 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

And when you select 3 first checkboxes AND THEN PLUG BOARD? Bootloader is in the STM chip. You can't screw it up. The "where to boot from" stm32 selects by the value of 2 pins... BOOT0 and BOOT1 (pins 44 and 20). In normal boot (from flash), both pins should have solid 0!... Which is what ...
by FedorCommander
Fri Mar 27, 2015 8:59 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

It shouldn't that happily blink green led when in bootloader mode... Led stays green during gyro calibration. Keep board ON THE DESK. It helps. Try following: v - no reboot sequence v - flash on connect v - full chip erase o - flash slowly Select firmware, load online... Short boot pins. Make sure p...
by FedorCommander
Thu Mar 26, 2015 9:05 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Seems i find it. Was micro crack on one of the ground wire (probably because of hit or crash, and this one is very close to the edge of the board.

It was just a hair crack, i made it big.... ;)

Floating ground
Floating ground
by FedorCommander
Thu Mar 26, 2015 8:24 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Have a weird issue... Naze32 acro, rev5. When powered up, its 50-50 if it boots up or not. If boots up - all works as a charm. If not - Just blue led. Boot pins are pulled to the ground (boot from flash). (Well, they were kinda floaty after all) When booted up, i can reset the board with shorting pi...
by FedorCommander
Wed Jan 28, 2015 8:49 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 625392

Re: MultiWii EZ-GUI

Thanks a lot...
by FedorCommander
Wed Jan 28, 2015 12:14 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 625392

Re: MultiWii EZ-GUI

Hi there! Does it work over usb on 4.4.2 ???? Cant get this thing working over USB. After installation it was crashing with Invalid BT!!!! address in the stack trace.... Ok. I made fake connection to some BT device, just to get some address valid... Then I switched back to serial usb.... Well, it st...
by FedorCommander
Sun Apr 20, 2014 8:55 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Yep, it's gone. I wish people would just stop wasting time with bluetooth... Or at least use proper modules. Do you have any more information about this? This is the first i've heard of people frying their hardware with bluetooth modules and i would quite like to avoid making that mistake myself if...
by FedorCommander
Thu Apr 17, 2014 4:08 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Make a custom mixer Thanks master. Can you confirm? mixer CUSTOM cmix 1 1 -1 1 1 cmix 2 1 -1 -1 -1 cmix 3 1 1 1 -1 cmix 4 1 1 -1 1 Right? Answer to myself... Just maiden it... Holy cow... With default pids, its like a train oN rails... Better then CC3D i had before!!! And custom mix does the trick....
by FedorCommander
Thu Apr 17, 2014 11:20 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

timecop wrote:Make a custom mixer


Thanks master.

Can you confirm?

mixer CUSTOM
cmix 1 1 -1 1 1
cmix 2 1 -1 -1 -1
cmix 3 1 1 1 -1
cmix 4 1 1 -1 1

Right?
by FedorCommander
Thu Apr 17, 2014 7:38 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

nspierbundel wrote:If it flies and corrects correctly just invert yaw on your transmitter.
Or read up on the custom mix (cant help you with that)


Transmitter reverse will not help, and even worse, will lead to crash. FC does corrections on its own.
by FedorCommander
Thu Apr 17, 2014 7:00 am
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Hi Guys! Sorry for noob question. How can i change motor direction in CLI for QuadX mixer??? I have frame, which has opposite rotations, and all wires are soldered, shrinked, shortened, so no joy to rewire. You could mount the motors facing downward. Or as others have said, use different ESC firmwa...
by FedorCommander
Wed Apr 16, 2014 9:07 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1381891

Re: Naze32 hardware discussion thread

Hi Guys!

Sorry for noob question. How can i change motor direction in CLI for QuadX mixer???

I have frame, which has opposite rotations, and all wires are soldered, shrinked, shortened, so no joy to rewire.

Thanks!