Search found 11 matches

by n00b
Fri Oct 21, 2011 3:51 pm
Forum: General discussions
Topic: Copter returns to "neutral" position after a while in GUI
Replies: 6
Views: 1072

Re: Copter returns to "neutral" position after a while in GU

I have the same problem and the graph of the accelerometer is not shown
can you tell me if I make mistakes or is a GUI bug?
I tried clone NK and ADXL345
http://www.youtube.com/watch?v=ULcoTBYymNk
by n00b
Wed Sep 28, 2011 6:59 pm
Forum: Connecting elements
Topic: anyone know how to fix this?
Replies: 9
Views: 1730

Re: anyone know how to fix this?

After I cut the nk creates the same problem ... I tried 5 and 3.3v
I finally bought an ADXL345 from 20 25 day arrives and can try
by n00b
Fri Sep 23, 2011 5:49 pm
Forum: Connecting elements
Topic: anyone know how to fix this?
Replies: 9
Views: 1730

Re: anyone know how to fix this?

I have been intending to purchase one of these for testing however, I have purchased some MMA7455s from the same vendor and they work great. The ADXL345 appears to have the same design and can use either 3.3 or 5 volts. It should be a plug and play solution but I can not say for sure. I do not see ...
by n00b
Fri Sep 23, 2011 12:11 pm
Forum: Connecting elements
Topic: anyone know how to fix this?
Replies: 9
Views: 1730

Re: anyone know how to fix this?

I found this on ebay can you tell me if it creates problems in parallel connection or if it's good?
http://www.ebay.com/itm/ADXL345-Digital-Sensor-Acceleration-Module-arduino-/260850156864?pt=LH_DefaultDomain_0&hash=item3cbbe18540
by n00b
Wed Sep 21, 2011 8:39 pm
Forum: Connecting elements
Topic: anyone know how to fix this?
Replies: 9
Views: 1730

Re: anyone know how to fix this?

works normally so is the NK
if I cut the NK in the middle? can solve the problem?
by n00b
Tue Sep 20, 2011 1:36 pm
Forum: Connecting elements
Topic: anyone know how to fix this?
Replies: 9
Views: 1730

anyone know how to fix this?

http://www.youtube.com/watch?v=sNPFCPRg0QQ I use: arduino nano v3 itg3205 gyro parallel nk connection v1.8 software and the config is # define I2C_SPEED 100000L # define ITG3200 # define NUNCHACK # define ITG3200_LPF_256HZ # define INTERLEAVING_DELAY 3000 can you tell me how to fix or if it is a gu...
by n00b
Fri Sep 09, 2011 5:37 pm
Forum: Connecting elements
Topic: itg3205 + gh0901b + help
Replies: 6
Views: 1971

Re: itg3205 + gh0901b + help

I will read your blog and I have connected the wm+ and nk on pin 3.3v
The result is a voodoo dance :shock:
# define I2C_SPEED 100000L
# define ITG3200
# define NUNCHACK
# define ITG3200_LPF_256HZ
# define INTERLEAVING_DELAY 3000
by n00b
Fri Sep 09, 2011 12:54 pm
Forum: Connecting elements
Topic: itg3205 + gh0901b + help
Replies: 6
Views: 1971

Re: itg3205 + gh0901b + help

this is the way of connection should I do?
by n00b
Fri Sep 09, 2011 7:22 am
Forum: Connecting elements
Topic: itg3205 + gh0901b + help
Replies: 6
Views: 1971

Re: itg3205 + gh0901b + help

I knew your blog, through you I was able to connect itg3205 (so thanks again)
in the attachment you can see that it works correctly

config:
#define I2C_SPEED 100000L
#define ITG3200
#define ITG3200_LPF_256HZ
#define INTERLEAVING_DELAY 3000
by n00b
Thu Sep 08, 2011 10:34 am
Forum: Connecting elements
Topic: itg3205 + gh0901b + help
Replies: 6
Views: 1971

itg3205 + gh0901b + help

hello all this is my little problem is my first quadcopter and this is the hardware that I have connecting them work individually but not in parallel v1.8 software and the config is # define I2C_SPEED 100000L # define ITG3200 # define NUNCHACK # define ITG3200_LPF_256HZ # define INTERLEAVING_DELAY 3...
by n00b
Sat Jul 30, 2011 3:59 pm
Forum: General discussions
Topic: quadcopter controlled via pc?
Replies: 8
Views: 4703

quadcopter controlled via pc?

Hi all
Will be a stupid question but I can not find a sure answer
you can replace the radiocontroller with a apc220 to completely control the quadcopter from pc?
thanks for any replies