Search found 14 matches

by vistauser
Wed Sep 25, 2013 11:00 am
Forum: MultiWii tweaking - flying experience
Topic: dev_2013_08_23_r1573_pre_2.3 user feedback
Replies: 14
Views: 5447

Re: dev_2013_08_23_r1573_pre_2.3 user feedback

Hi MultiWii fans, My copter: MWCX 45cm Props are cut to 9" EPP1045 EMAX 2213-935Kv Flyduino 25A ESC SimonK firmware. 3S1P 2200 mA Akku. Flyduino Mega FC, ATAVRSBIN1 Sensorboard, BMP085 on Flydusense, FMP04 serial GPS on Flyduino FMP04 GPS Bob TX a Spektrum DX7 with Satellit RX. First results: C...
by vistauser
Fri Mar 15, 2013 12:57 pm
Forum: Software development
Topic: MultiWii 2.2 is released
Replies: 84
Views: 60947

Re: MultiWii 2.2 is released

Hallo Marc,

good finding. I applied your change and the bat low warning now is as expected.
No negativ side effects seen.
For me the former double blib was the signal for landing, now its the single blib.

Olaf
by vistauser
Mon Mar 11, 2013 9:35 pm
Forum: Software development
Topic: MultiWii 2.2 is released
Replies: 84
Views: 60947

Re: MultiWii 2.2 is released

@Stars112 you are absolute right with Point3: setting the box for ARM into the former box of STABLE was DANGEROUS. It happend to me when I testet one of the first 2.2dev version, this feature was introduced. The copter started unexpected and flew off the table. Two broken props, connection between c...
by vistauser
Wed Oct 31, 2012 5:25 pm
Forum: Software development
Topic: No GPS-fix indication with new dev versions
Replies: 3
Views: 2091

Re: No GPS-fix indication with new dev versions

Hallo, tnx alexinparis, with r1240 now nice gps indications at the stable led on my flyduino mega fc and serial fmp04 gps. only blinking with sat <5 stops after some seconds from power on and doesnt start blinking again if sats lower from 5 to 4. altitude indication still fluctuating around zero (in...
by vistauser
Thu Oct 25, 2012 12:49 pm
Forum: Software development
Topic: No GPS-fix indication with new dev versions
Replies: 3
Views: 2091

No GPS-fix indication with new dev versions

Hi, in firmware v2.1 i got nice fix indication with sat >=5 by the status LED blinking (ser. NMEA GPS is installed). After testing r1177 and now r1232 this doesnt work anymore. Without this fix indication GPS is unuseable. With #define GPS_LED-INDICATOR uncommented in r1232 i get some compiler error...
by vistauser
Mon Oct 22, 2012 8:14 pm
Forum: General discussions
Topic: SKYLAB SKM53 compatability ?
Replies: 13
Views: 6107

Re: SKYLAB SKM53 compatability ?

Hi Nik, i am using this GPS in nmea mode and it works in gui and i get outside also a fix indicated by the flashing status led. to your question: my setting for the above 3 parameter is 1 (not 10), the other not used parameters are 0. finally i tap on the "Confirm" button. under the tab Te...
by vistauser
Mon Sep 17, 2012 12:11 pm
Forum: Software development
Topic: Altitude Hold improvement solution
Replies: 580
Views: 1581780

Re: Altitude Hold improvement solution

@ROB tested ALTHOLD today with your V3 final software. PID setting 10.0//0.020//60 We had various wind conditions: at no wind AH was very good +- 20cm smooth up and down, with gusty winds altitude changes up to +- 1m, but always safe and smooth. During flying the MC around AH still worked as expecte...
by vistauser
Thu Aug 02, 2012 9:26 pm
Forum: Ideas
Topic: 0.96" SSD1306 128X64 OLED Display Module
Replies: 207
Views: 235963

Re: 0.96" SSD1306 128X64 OLED Display Module

Hamburger,
thanx, will try that
by vistauser
Thu Aug 02, 2012 1:26 pm
Forum: Ideas
Topic: 0.96" SSD1306 128X64 OLED Display Module
Replies: 207
Views: 235963

Adding the OLED display to my Copters - I2C problems

The below mentioned problems occur on both of my copter platforms with 2.1 firmware and standard PID settings. 1. Arduino Pro Mini with ATAVRSBIN1 sensor board, orange 6 ch rx 2. Flyduino Mega FC, ATAVRSBIN1, BMP085, FMP04 GPS on Flyduino FMP04 GPS Bob, Spektrum SAT RX Initial power on of the copter...
by vistauser
Thu Jul 19, 2012 10:36 am
Forum: Software development
Topic: Once again about MAG
Replies: 21
Views: 9197

Re: Once again about MAG

Hi,

yesterday I made it! Copter doesnt yaw to the left anymore with MAG switched on.
Howto:
Clear eeprom first prior flashing new firmware, do all settings new in gui and also do all calibrations.
Clear eeprom is a tool from arduino v 1.01.

Good luck
Olaf
by vistauser
Mon Jul 16, 2012 5:28 pm
Forum: Software development
Topic: Once again about MAG
Replies: 21
Views: 9197

Re: Once again about MAG

Same happens here.
Without switching mag on heading hold is perfect. After some seconds with mag - on copter starts irratigly to yaw to the left.
I think on my sensor board the mag is active per default. What for is the option with the switch?

Any thoughts about?
Olaf
by vistauser
Sun Mar 25, 2012 7:12 pm
Forum: Software development
Topic: Combination of BMP085 and ATAVRSBIN1 not working
Replies: 7
Views: 2371

Re: Combination of BMP085 and ATAVRSBIN1 not working

Hi Andrej,

I´m using BMP085 and ATAVRSBIN1 on a Paris v4.0 board and this combination is working fine
with MULTIWII SW 2.0pre4. Height hold and heading hold is satisfying with default settings.

mfg
vistauser
by vistauser
Tue Jul 26, 2011 10:28 am
Forum: Software development
Topic: Atmel Inertial One System Board ATAVRSBIN1 support added
Replies: 81
Views: 39168

Re: Atmel Inertial One System Board ATAVRSBIN1 support added

Hi captaingeek,

its a 40cm quadcopter with the attached settings.
Thanks for the explanation.

vistauser
by vistauser
Mon Jul 25, 2011 8:25 pm
Forum: Software development
Topic: Atmel Inertial One System Board ATAVRSBIN1 support added
Replies: 81
Views: 39168

Re: Atmel Inertial One System Board ATAVRSBIN1 support added

Hello, today I received my Paris v4.0 board and assembled it with the ATAVRSBIN1 mounted 90 ° ccw. The MWC+ just made its maiden flight indoor on 3x3 meters and I´am completely happy with its stability. In this small area only stable mode is possible. Using the development sw 0714 with default setti...