MultiWii

a quick embarrassing update, ive just check google earth for true north and as im sitting on my sofa its behind me hence thats why the arrow was back to front when i turned on my laptop facing north and quad facing north it all lined up perfectly ,i feel a right donut right now but if it helps other...

i have a flyduino and allinone from csg ive setup in 1.8 patch2 define allinone and so on change mag settings solder two jumpers on allinone and so on, i fly quad x ,problem is flys ok and stabilizes ok but when i connect to gui the gui is say showing arrow up, and my quad holding in my hand arrow o...

http://www.youtube.com/watch?v=aSdYkwIJ-Vg
slow motion
http://www.youtube.com/watch?v=qDoyhrT0tJs
damage one prop
alley arm not bad really thats what we like easy fix cant beat it.
ps sorry about some of the bad language in the video should of edited it out ..

i have a flyduino with the allinone board the compass dont look right ,heres my settings, can anyone tell me if anything is wrong thanks a million.. dave... You tube video also excuse my amature video i done it on the quick.. m /* Set the minimum throttle command sent to the ESC (Electronic Speed Co...

why did you solder both jumpers i only did one

hi oliver above has got the right idea you must calibrate gyro, also check your radio is connected to your receiver because you should see the bars on gui move with radio ,aslo i noticed that you have a wm+ clone you must change #define I2C_SPEED 100000L //100kHz normal mode, this value must be used...

you could try from the basics first disconnect nunchuck and just have wm+ connected see what happens then..

i have my quadcopter aux 1 set to channel 5 off my tx and its on high ,i was wondering in the gui 1.8 dev its got low med high ive set mine to high call me stupid but what does low and med used for any info would be great cheers everybody.. dave.. ps ive checked internet but could not see any thing ...

thanks loosi and kayle your infos been great ,i wondered why it was doing weird things ive change address to 0x82 for bma180
and resoldered bride and extra ground ,also change mag to new mag
seems to be flying ok now cheers dave..

thanks alexinparis it makes more sense now. so basicaly it adjust the pid settings to what throttle youve aplied on the fly to stop wobbling at high revs. i take it.
dave..

hi loosi is there any reason you have to bridge the board and ad the extra ground any info would be great
dave...

you could look at the cut off voltage on the escs, programming card it should be all the same, i think its low middle high it should be middle to high i think perhaps someone can correct me hope this helps.
dave

thanks ray answer my question ive just got board in post be setting up soon
dave

how does it control the altitude by software ? does it take readings then control throttle?

ps can anyone tell me if the gyros and acc are better than mw+ numchuck cheers dave...

ive just bought this board looks like a bargain coulndt find anywhere else ill let you know how i get on
dave..

i had the same problem the fix i came up with was the baud rate was 9600 on the bluetooth and all i did was to change audrino 1.7 baud rate from 115200 to 9600 uploaded to multiwii
then it work, hope this helps dave..

will it work with

http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0708289497
cheers dave..

latest situation is i bought a serial lcd from ebay m ive wired it up on four wires 5v tx rx gnd all that happens is lcd lightes up and says (press cr)The CR means carriage return or the enter key on the keyboard. Pressing <enter> will clear the display and produce a ‘*’ on the terminal i can make t...

thanks for reply ive just ordered serial 16 x 2 seems easier solution cheers dave..

can you tell me what this throttle rate does, ive read what it does on multiwii.com and im still confused is it similiar to endpoints
cheers in advance dave..

i see what you mean nobee can i not use it at all then?

check cycle time should be 6000 for both connected, if not may have to change interleave from 3000 to 4000

does anyone know how to wire three wires to this lcd cheers dave

http://www.hobbytronics.co.uk/lcd/polol ... -backlight

thanks patrik that makes sense

hi i have hk 18a turnigy plush esc my question is is there a gadget for calibrating all escs at once like the gaui330x