Search found 7 matches
- Sun Dec 08, 2013 6:22 am
- Forum: General discussions
- Topic: Controlling a Camera Gimbal using Aux Channel?
- Replies: 12
- Views: 10833
Re: Controlling a Camera Gimbal using Aux Channel?
Hi, The current MIX_TILT is not able to handle an AUX superposition. could you replace and test this part: ? #ifdef SERVO_MIX_TILT #if defined(A0_A1_PIN_HEX) && (NUMBER_MOTOR == 6) && defined(PROMINI) #define S_PITCH servo[2] #define S_ROLL servo[3] #else #define S_PITCH servo[0] #d...
- Sun Dec 08, 2013 3:57 am
- Forum: General discussions
- Topic: Controlling a Camera Gimbal using Aux Channel?
- Replies: 12
- Views: 10833
Re: Controlling a Camera Gimbal using Aux Channel?
I'm using the MultiWii Config 2.3 GUI that came in the MW 2.3 zip file. I don't see anything there for changing servo direction, min/max settings, or any other adjustments. Is there another GUI that allows for this? I've tried using WinGUI 2.3 beta3, but can't connect to my board with it (no problem...
- Sat Dec 07, 2013 10:56 pm
- Forum: General discussions
- Topic: Controlling a Camera Gimbal using Aux Channel?
- Replies: 12
- Views: 10833
Re: Controlling a Camera Gimbal using Aux Channel?
Hope no one minds me jumping in here too as I'm hoping to set up my SSG for manual tilt control too. I have a couple of questions in this line too: 1) My cam stab pitch was working backwards. After some searching I finally changed this line in the Output.cpp: #ifdef SERVO_MIX_TILT int16_t angleP = g...
- Sat Nov 30, 2013 5:42 pm
- Forum: Software development
- Topic: 2.3 is finally here :)
- Replies: 97
- Views: 118406
Re: 2.3 is finally here :)
Thanks all. I got my stick commands working. It turned out it was a Tx end point issue. I had my Tx AIl and Ele at 90%, which worked for fw 2.1 but not 2.3. Once I bumped all the EPAs to 100% the stick commands starting working again. Thanks for the help. 

- Sat Nov 30, 2013 7:29 am
- Forum: Software development
- Topic: 2.3 is finally here :)
- Replies: 97
- Views: 118406
Re: 2.3 is finally here :)
Thanks. Higher throttle setting shouldn't make a difference for Gyro Calibration...where down throttle is used, but I'll certainly check all the EPAs. Perhaps it is just insufficient throws causing the problem. I hope to get it figured out. I liked the feel of the Horizon flight mode; I just couldn'...
- Fri Nov 29, 2013 6:43 pm
- Forum: Software development
- Topic: 2.3 is finally here :)
- Replies: 97
- Views: 118406
Re: 2.3 is finally here :)
Ah...thank you. I didn't do that part...totally forgot about it. Thank you. edit: Nope. That didn't work either. Maybe I'll just back down to 2.1 again? edit-edit: I just loaded 2.1 back into my FC (erased, then reload) and my stick configuration works fine. So maybe something I did wrong with the e...
- Fri Nov 29, 2013 5:42 pm
- Forum: Software development
- Topic: 2.3 is finally here :)
- Replies: 97
- Views: 118406
Re: 2.3 is finally here :)
I just loaded 2.3 into my NanoWii control board (formerly using 2.1). It appears my 'stick commands' aren't working right. I can arm and disarm with no problem. I can't get it to do the Gyro Calibration nor ACC Trim. I don't know if I'm doing something wrong or if something has changed in 2.3 in how...