MultiWii

Minim OSD mit KV-Team R3.70, Crius AIO V2, Multiwii 2.3 after arming still "disarmed" in OSD no change of flightmode icons (Battery, angle, heading are working) "Use Boxnames" is checked in GUI. Any ideas? Problem with MW 2.3 ?? Louis Hi Louis, no, no problem with MW SW compatib...

Minim OSD mit KV-Team R3.70, Crius AIO V2, Multiwii 2.3

after arming still "disarmed" in OSD
no change of flightmode icons
(Battery, angle, heading are working)

"Use Boxnames" is checked in GUI.

Any ideas?
Problem with MW 2.3 ??

Louis

Thanx, the minimOSD is working now on Serial3 on Crius AIO V2.

It was working on serial0, not on serial3.
The problem was the KV-Team-Software on osd. After uploading again, reset all, it's working on serial3.

Louis

additional:
how to change osd-port serial1 to serial3 on Multiwii V2.3 ???

similar question,

I use
serial 1 for s-bus
serial 2 for gps
nice to have serial 3 for minimosd.

how to change osd-port serial1 to serial3 ???

Louis

I use futaba S-Bus receiver with Crius AIO V2 all perfect... I ordered Boscam HD19-camera with possibility to remotly control camera-shot or video start/stop. It can be done by Aux-channel: Aux-Level middle: standby Aux-Level low: snapshot foto Aux-Level high: Video start Aux-Level middle: Video sto...

I found it (thanks to U.Sentenza) in Output.cpp missing lines.... AUX5, AUX6 for gimbal-control Nick, roll with RC-Control also #if defined(SERVO_TILT) servo[0] = get_middle(0); servo[1] = get_middle(1); if (rcOptions[BOXCAMSTAB]) { servo[0] += ((int32_t)conf.servoConf[0].rate * att.angle[PITCH]) /5...

in MW-Gui 2.2 there's no servo tab.
on http://code.google.com/p/mw-wingui/downloads/list
there's no new MW-Gui 2.3 to download.

What gui You use?

Louis

It's possible to see the current of lipo now used, not the sum since start?
with external current sensor setup?

Louis

like MW 2.2: #define SERVO_TILT #define TILT_PITCH_MIN 1155 //servo travel min, don't set it below 1020 #define TILT_PITCH_MAX 1822 //servo travel max, max value=2000 #define TILT_PITCH_MIDDLE 1500 //servo neutral value #define TILT_PITCH_PROP 20 //servo proportional (tied to angle) ; can be negativ...

After MW2.3 r1604 uploading to Crius-AIO V2.0-Board all is fine... After "writing settings to board" (without changing something) via MWWin-Gui 2.2: arming is different. Before writing settings to board arming motors: level to ESC is 1200 (min throttle) - 1836 (full throttle), all is fine ...

when you start the app, bluetooth gets always switched on. Nice to get a flag for using bt or not.
bt use extra power...
I use 3dr-radio at usb on htc-one, using serial-config.

Louis

with MWC-Software V2.1 it works fine.
something wrong in config.h, rx.ino ???

Some help...?

Futaba FX-20 with R 6108 SB, MWC V2.2 Software S-Bus with HEX-Inverter SN74LS04 in line from receiver to AIOP Serial 1, RX1 connected. (like config.h sbus-description) SN74LS04-Inverter made by my own (Pin 14: 5V+, Pin7: ground, Pin1: SBUS from Receiver, Pin 2: Output to AIOP) in config.h: #define S...