MultiWii

theailer

Either install older version of arduino or download the beta version of mwosd.
FYI Google code is deprecated and I think you mean github.

theailer

Maybe plan a little better next time

theailer

Your best bet will be baseflight or cleanflight.

theailer

It would be quite easy to determine. Just push full up on elevator and see if it's travels half of the servo range or if you have instructions from the manufacturer to determine max elevator deflection. And then do the same for aileron and lastly both together.

theailer

PatrikE wrote:
theailer wrote:It has to be a pal/NTSC mismatch. Change it so both camera and osd is the same.

That was the case!...
Thank's

Np. Glad to help you for once

theailer

PatrikE wrote:
theailer wrote:It has to be a pal/NTSC mismatch. Change it so both camera and osd is the same.

That was the case!...
Thank's

Np. Glad to help you for once

theailer

It has to be a pal/NTSC mismatch. Change it so both camera and osd is the same.

theailer

Or you could do a little hack and just use a heli gyro for the rudder. Maybe not the prettiest solution but it works

theailer

captaingeek wrote:any recommendations on using this for a flying wing? IE only 2 servos?

It's pretty straight forward. Just type mixer flying_wing in cli to enable it.

theailer

Hehe. It will most likely never have GPS built in

theailer

timecop wrote:acroboard will always drift yaw, there's no temperature or bias calibration in firmware.
if you reconnect it after letting it warm up, the drift will be lessened.

Crap. It isn't the first time I forget it's a acroboard...

theailer

Do you calibrate it near your computer? Might be a magnetic field around your computer or escs. But this would not affect rate/manual mode I think

theailer

And if you buy the support package from abusemark he will blacklist your sorry ass and refund your money. How nice isn't that

tc, I love you man!

theailer

Best thing I've read this week

theailer

Did u click save?

theailer

Sry. It was on a Swedish forum.

theailer

A guy from another forum had sorta the same issues as you and it turned out to be a faulty receiver.

theailer

I think I killed another naze. No led at all when connecting with USB or flight batt. I am using a 5v bec. The output of 5v goes to naze and rx, mwosd all got power from pins from Naze board. This was the SS 5v/3a ubec I used before. Care to whip up a diagram of your wiring? I have the same problem...

theailer

It's on a plank. I had a servo gone bad so I'm hoping that was the culprit, can a servo brick a naze if it's only connected to it with the signal pin?

theailer

Ok, i measured 3v across the esc's signal and ground. Is that normal ? None of my other esc's do that.

theailer

BEC output of 5.3V shouldn't cause it- my BEC outputs 5.5V and no issues- the regulator on the Naze32 should easily be able to handle that. Are you powering anything off the Naze32 3.3V rail? Are you using 5V devices on the I2C bus? Any 5V inputs on the 3.3V GPIO pad or 3.3V ADC pad? I have a ublox...

theailer

Smoked another one. Guessing that my bec outputting 5.3V has something to do with it

theailer

Ah crap. Wish I knew that before

I've seen others having problems with it but never really reflected upon it. Damn..

theailer

I've busted a whole lotta nazes recently, and the one thing I can think of that's fracking them up is that I'm powering them from my rx. Would it be possible to destroy them this way ? Some nazes lost signal out on random motor outputs, and the last one worked but all of a sudden all control went cr...

theailer

You have to enable it in the CLI I think

theailer

It overclocks the naze so there is less noise on the UHF band. Good to have if you use any type of long range system

theailer

Sweet. Thanks for the info

theailer

I've always used a naze r5 for harakiri. No problems here

theailer

A million thanks dude! Will check it out when I get home.

theailer

Yup airplane mode. I suppose its in mixer.c . Ive looked through the code and since I havent learned to code I guess now would be a perfect opportunity. Can you tell me if im supposed to look at line 327 to 336 in mixer.c? Or is it not that easy?

theailer

Okey. What about shifting the motor 1 output with the motor2 then ?

theailer

And to confirm the fault, it was me who damaged the board by soldering the tx-rx pins to it. Now my white board doesnt respond on M1 which is to the esc. Still would be interested in knowing if it's possible to change the pwm outs to another pin.

theailer

Can I set elevator to M2 instead of m6 in the command line interface or does it require altering the source code ?

theailer

Yeah. It has to be me handling them wrong. Maybe I fucked them up when soldering the tx and rx pins.

theailer

Hi. I'm having trouble with the airplane mixer. On my white rev3 naze it works like it should, but on the new rev4 elevator wont work. I have the same pin connected as with the white but it doesn't send any signals to the servo. I've tried two rev4 boards and neither work, but they do work with my q...

theailer

That's the way I have it on my quad as well. And it still only recognize the gps in harakiri.

theailer

My ublox 6 gps doesn't work in baseflight but with the same settings it works in harakiri for some strange reason

theailer

I don't think that removing the +5v cable from the escs servo contact make a difference at all.

theailer

It let's you know the date it was compiled which makes it pretty easy to check the revision

theailer

theailer

Try typing three #

theailer

How hard can it be to post in the right forum? This threads keep popping up in the 32bit section. Got to wonder what have happened to the gene pool...

theailer

I've had a intermittent faulty USB cable which would render me the same symptoms. Changing the cable ended my frustration

theailer

Great. I have it on type 1 now and it works. Tried position hold which I guess is the same as GPS hold in the GUI. It did wander a couple of meters and had some sort of toilet bowl effect, but I had no time to tune it out and I guess my shield plate weren't connected to a ground might also have some...

theailer

If I set gps_type = 1, will it disregard the config file regarding update frequency ? Since the 3dr ublox file sets it to 4Hz and the ginjei file sets it to 5Hz, and I can't flash it with the ginjei file.

theailer

Ok, got it to work though I'm fairly sure it worked since the start. I'm using wingui2 and I always looked in the passgps tab for the gps info. Turns out it doesn't output anything. Switching to the MAP tab did indeed verify that the gps was working OK. Tried to put the ginjein file on my ublox but ...

theailer

Thanks. I've ordered an adapter but it haven't arrived yet.

theailer

This one
http://www.goodluckbuy.com/ublox-high-p ... ntrol.html

theailer

1st post

I have summer games 2.5 on my naze32 with a gps. The naze blinks red confirming satellite lock but no GPS data in the various guis. Should it be this way or am I missing something?

MultiWii

Search found 49 matches

Re: MultiWii OSD - MWOSD

Re: MultiWii OSD - MWOSD

Re: Airplane mode

Sv: Naze32 hardware discussion thread

Sv: Naze32 hardware discussion thread

Re: Naze32 hardware discussion thread

Sv: Naze32 hardware discussion thread

Re: Naze32 hardware discussion thread

Re: Naze32 hardware discussion thread

Re: Baseflight aka multiwii port to stm32

Re: Baseflight aka multiwii port to stm32

Re: Baseflight aka multiwii port to stm32

Re: Harakiri aka multiwii port to stm32

Re: Harakiri aka multiwii port to stm32

Re: Harakiri aka multiwii port to stm32

Re: Harakiri aka multiwii port to stm32

Sv: Harakiri aka multiwii port to stm32