Just checked the FTDI red and green light flash when connected to the GUI. dOH!
When you connect does the correct type show up. IE quad X?
I have the Paris V3 board so don't know if there is a diff.
Cheers
Search found 11 matches
- Tue Aug 07, 2012 9:02 am
- Forum: MultiWii tweaking - flying experience
- Topic: Paris FC HELP!!
- Replies: 3
- Views: 1576
- Tue Aug 07, 2012 8:15 am
- Forum: MultiWii tweaking - flying experience
- Topic: Paris FC HELP!!
- Replies: 3
- Views: 1576
Re: Paris FC HELP!!
Hi I think if you were able to upload the sketch to the board then the FTDI seems to be working. I would check for the usual Com ports, baud rate settings for the arduino side. Then check the multiwii GUI com ports etc is correct. Are you getting any info from the Board showing up in the GUI apart f...
- Fri Jun 29, 2012 9:57 am
- Forum: Software development
- Topic: WinGUI 2.1 Beta is released for testing
- Replies: 96
- Views: 29412
Re: WinGUI 2.1 Beta is released for testing
Thanks from Australia too, EOS. Great work.
- Thu Oct 13, 2011 12:58 am
- Forum: MultiWii tweaking - flying experience
- Topic: Tricopter Flipping Out on 1.8 Help please
- Replies: 23
- Views: 6499
Re: Tricopter Flipping Out on 1.8 Help please
Hi all. Plus 1 on da flipping quad. Happened 3 times now since 1.8.2 30A plush esc. acro fine but seems to flip whilst in stable mode and after recovering from high angles of bank. Have caught 2 flips on camera. Will upload. Cheers Flip No 1. m Flip No 2. m Resetting all conf back to default to tes...
- Wed Oct 12, 2011 1:02 pm
- Forum: MultiWii tweaking - flying experience
- Topic: Tricopter Flipping Out on 1.8 Help please
- Replies: 23
- Views: 6499
Re: Tricopter Flipping Out on 1.8 Help please
Hi all. Plus 1 on da flipping quad.
Happened 3 times now since 1.8.2
30A plush esc. acro fine but seems to flip whilst in stable mode and after recovering from high angles of bank.
Have caught 2 flips on camera. Will upload.
Cheers
Happened 3 times now since 1.8.2
30A plush esc. acro fine but seems to flip whilst in stable mode and after recovering from high angles of bank.
Have caught 2 flips on camera. Will upload.
Cheers
- Mon Oct 10, 2011 3:15 pm
- Forum: ESCs, propellers , servos and radios
- Topic: Motor orientation
- Replies: 7
- Views: 2511
Re: Motor orientation
tovrin wrote:going to assume its not a big deal outside the inherent dangers of debris during landing since noone has replied
I was thinking it could double up as a weed trimmer
Have heard it eliminates the frame from the downwash.
Would you need to turn your props upside down on the motors?
Cheers
- Wed Oct 05, 2011 7:24 am
- Forum: Shields, boards and sensors
- Topic: FTDI to pro mini problem.
- Replies: 5
- Views: 3269
Re: FTDI to pro mini problem.
Looks like there is a problem with the sixth wire/connector which is DTR signal, it resets the processor to start the bootloader. That's exactly what you do manually but the timing is critical. Check you wiring/pin/socket/etc., cannot give more specific advice since I don't know which FTDI adapter ...
- Tue Oct 04, 2011 8:21 pm
- Forum: Shields, boards and sensors
- Topic: FTDI to pro mini problem.
- Replies: 5
- Views: 3269
Re: FTDI to pro mini problem.
i had a very similar problem, turned out that i had destroyed one of the chips in my arduino related to USB loading. you could see several micro wires on the chip right behind the usb port of my Duemilanove got hot and seperated. i do believe it held its last config and works fine, i just bought a ...
- Tue Oct 04, 2011 7:56 pm
- Forum: Pictures & Videos
- Topic: Phone taped to Quad as Camera!
- Replies: 0
- Views: 1143
Phone taped to Quad as Camera!
Don't know what went wrong here but I used phone as a camera.
WiFI, GPS, BT etc turned off to be safe..
Seemed to loose control and had a near miss with the planet.
Caught it just in time and landed.
http://www.youtube.com/watch?v=YXJ7Pd7EEOA
Note to self hold all calls whilst out flying.
WiFI, GPS, BT etc turned off to be safe..
Seemed to loose control and had a near miss with the planet.
Caught it just in time and landed.
http://www.youtube.com/watch?v=YXJ7Pd7EEOA
Note to self hold all calls whilst out flying.
- Tue Oct 04, 2011 10:11 am
- Forum: Shields, boards and sensors
- Topic: FTDI to pro mini problem.
- Replies: 5
- Views: 3269
FTDI to pro mini problem.
Hi all. First off I am new to this and am having a great time building and then crashing my Quad. Having some trouble when uploading software to the board. Arduino compiles fine, then when I upload it comes back with a sync error. No TX or RX lights on the FTDI, just three quick red flashes. Happens...
- Wed Aug 10, 2011 8:16 pm
- Forum: Software development
- Topic: v1.8
- Replies: 69
- Views: 28793
Re: v1.8
Great work!!
Looking forward to testing this. My Paris Board is the only part still working after my latest crash/test flight.
Looking forward to testing this. My Paris Board is the only part still working after my latest crash/test flight.