MultiWii

bob195558

Hi, Need some help. I did have last year MultiWiiConf working on my Win7 computer last year. When trying to open MultiWiiConf, it gives an Unspecified error, I thing with JAVA path maybe: (C:\ProgramData\Orade\Java\javapath\javaw.exe) I am in process of setting up the older MultiWii PRO Flight Contr...

bob195558

Where did Witespy go ? Did not get an email from witespyquad letting me know about the change and after several days found this: ATTENTION!!! VERY IMPORTANT!!! AS PART OF OUR CONTINUED EFFORT TO IMPROVE, YOUR FAVORITE MULTIROTOR STORE HAS A NEW WEBSITE ! PLEASE save: (m) ! Had a hard time to re-fin...

bob195558

Hi FengShuiDrone, What you are stating may not be true and this is why I think it is not proper to connect multiple 5 Volt power sources together. I am powering 5 Volts of power to a MultiWii Pro Flight Control Board, an 8 channel Receiver, LED's, GPS, many Telemetry Sensors, Servos, 3DR Radio Telem...

bob195558

When using the MultiWiiConfig computer program that comes inside of the MultiWii_2.3 firmware downloaded zip file, which I now understand is a must need to do when setting up the arduino MultiWii Pro 1 board, otherwise the throttle throw maybe incorrect, is now working properly ! I wish I knew how t...

bob195558

Troubleshooting this morning discovered why everything stopped working: I am embarrassed to tell you why. The 3S Lipo battery voltage dropped down to 7.6 volts. With a good Lipo battery I am back to the original problem. This morning, I am starting with re-calibrating the ESC's/motors again to have ...

bob195558

Hi waltr, Thank you for your reply. Forgive me for my ignorance. I translated MultiWiConfig to mean Arduino MultiWiiConfig.h tab. I found the computer program MultiWiiConfig and had great difficulty getting it to install. But was able to get (application.windows32) to install. Was not able to get th...

bob195558

Hi waltr, Sounds like the FC had an early version of MW. This version of F light C ontroller, M ulti W ii Pro 1.0 board is from witespyquad: (m) (m). It had no problem before upgrading to: MultiWii_2.3 (m) firmware. Firmware at witespyquad all failed to compile, so was unusable. Then Always use the ...

bob195558

Hi everyone, My Quad motors start up only at center throttle stick and work, up to the full throttle travel. From the bottom throttle stick to center throttle stick, there is no motor start up. I updated this MultiWii Pro 1 Board with MultiWii_2.3 firmware and now I have this problem with the thrott...

bob195558

Also there is this: (https://code.google.com/p/openxsensor/w ... figuration)
with (http://openrcforums.com/forum/viewtopic.php?f=86&t=5882).

Bob B.

bob195558

Hi Made progress, now able to compile and flashed to this MultiWii PRO Flight Controller Board. Purpose was to change the Multicopter Motor Configuration and to add the GPS module. Went to: (m) and download MultiWii_2_3.zip file and opened it up in Arduino-1.0.6. Made selections in config.h tab: #de...

bob195558

Hi waltr, First time downloading MW2.3 (m) and using Arduino-1.0.3 version, it did not compile. So not to give up, I downloaded the newest Arduino-1.0.6 (windows) and installed it. Then I downloaded MultiWii_2_3 again and after I made some selection changes, #define HEX6X , #define FFIMUv2 , #define...

bob195558

Why are you using MW2.2? The latest is MW2.3. Did you download a fresh copy (.zip file) of MW2.3 and unzipped to a new folder and try building this without making any changes? Doing this will ensure there is nothing wrong with the project files. Hi waltr, The author of a youtube video said, MW2.2 w...

bob195558

The Drop box seems to be missing files. MW 2.3 has 26 files. what I think witespy has in there are only the files that needed changes for the features (GPS, etc). Examine the files from download from the MW repository to see this. What to try: Setup a Folder with all the MW files from unzipping MW ...

bob195558

Hi everyone,
This may be some help: (http://openrcforums.com/forum/viewtopic ... 811#p87675)
(http://openrcforums.com/forum/viewtopic ... lit=sensor)
(http://openrcforums.com/forum/viewtopic ... lit=sensor)
(http://openrcforums.com/forum/viewtopic ... sor#p84912)

Bob B.

bob195558

Hi all! I have a FrSky Taranis and an X8R and I'm using a HK multiwii pro FC on my quadcopter. As soon as I realized the idea of sending telemetry data from the FC to taranis by reading this post, I went mad ! Yet, I didn't understood if It is possible or not and I sincerely ask someone help ! Is t...

bob195558

Hi izeman,
With the values changing so quickly, maybe they are not real data values.
It maybe the sensor data is not getting through.
You may find help on the OpenRCforums being you are using er9x on your Turnigy9x.
Bob B.

bob195558

Hi PatrikE and everyone,

Paul's config.h firmware is having Error Compiling Problems.

I started a new post: MultiWii / Arduino / Error Compiling Problem !
Please go to it here: (viewtopic.php?f=22&t=5822)

Thank You

Bob B.

bob195558

Hi I am getting Error Compiling with the arduino-1.0.3 when using: MultiWii_MEGA1_GPS.zip / (m). I have also tried Compiling: MultiWiiV1_7.zip / (m) / (m) with the same Error Compiling with using arduino-1.0.3. I also tried the other ones and they all fail with Error Compiling. With this older Multi...

bob195558

Hi kalle123, Thank you for your reply. Should have titled this thread this way: Can arduino-1.0.3 read the config.h folder setting in the witespyquad MultiWii PRO Flight Controller Board ? (So to retrieve the config.h folder setting back into arduino-1.0.3 so to be able to view the config.h folder s...

bob195558

Hi, When trying to flash, Its not working! Error compiling! Arduino MultiWii Board 8_ Error compiling.jpg Arduino MultiWii Board 7_ Error compiling.jpg It even dose it with the stock downloaded firmware, (I made no changes in the config.h folder it was the stock downloaded firmware). Any idea whats ...

bob195558

Hi, Viewing witespyquad info for this Older MultiWii PRO Flight Controller board w/ GPS Option at: (m), it looks like the sensors are still the same. MultiWii PRO Flight Controller w- GPS Option - Flight Controllers 2014-11-13.jpg And so when I go to the witespyquad place for the (m) there looks to ...

bob195558

Hi Everyone, Thank you for your replies. I did not get any return email notifications so I had not see your replies until now. What I was hoping for, was to be able to retrieve the config.h file setting from this older MultiWii Board, so I could compare it to the present WiteSpyQuad config.h file se...

bob195558

Hi, I have been given an older MultiWii PRO Flight Controller board with out GPS
and I want to download and save a copy of its firmware.

: Older MultiWii PRO Flight Controller board with out GPS

Can I do this and how do I do it.

Bob B.

bob195558

Hi Arakon, Thank you for your help. I rechecked the GPS wiring (GPS serial port connections) and found the RX and TX were wrong, so fixed it and it still not working. I checked the on-board small battery and it is down to .287 DC V, may be its to low ? I changed to a different uBlox 6M GPS, which ha...

bob195558

I have an-other problem, now that I have this MultiWii PRO 2.0 Flight Controller w/ GPS Option board flashed with the MWC 2.3 / MultiWii_MEGAEZ3_GPS_HEX6X.ino firmware , the GPS is not working (m). The GPS I have is the an older one: uBlox 6M GPS (no compass). Viewing the MWC 2.3 / MultiWii_MEGAEZ3_...

bob195558

HI Arakon and everyone,

I added the DTR wire and when I activated the Upload button it auto-resets
and flashed the new firmware to the MultiWii Board.

YA!

it flashed the MultiWii Board !

Thank you Arakon and waltr for your help.

Bob

bob195558

HI Arakon and everyone, At: (m) (The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded . This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button . This board will auto reset any Arduino board that has the reset pi...

bob195558

I did not know about that, I will check it out!
Thank you for seeing it.

Bob

bob195558

Hi Arakon,
I tried the upload button and it Timed out (Failed)

bob195558

Hi Arakon, Waltr and everyone, I have made some progress with getting the MultiWii Firmware imported into the Arduino software. It seem the first several downloads of MultiWii_MEGAEZ3_GPS_HEX6X.zip firmware, were corrupted some how as they would not work correctly. With an uncorrupted MultiWii_MEGAE...

bob195558

Hi Arakon, Like I already wrote above, copy the remaining files to that folder and you're good to go. I did what you suggested and it still works the same wrong way. It did not work for me! Sorry I was not clear in my last post. The problem you are having is not a MW issue but you needing to learn h...

bob195558

Hi Arakon, When it moves the file to the new folder, did it move ALL the files in the folder, or only the .ino? If not all the files are in that folder, move them manually. arduino.jpg Only the .ino is moved to a new file. This may explains what is happening better: 9) Message Box pops up Titled, (M...

bob195558

Hi Arakon, Yes, on my computer Desk Top I have all the files. These are the steps I have been trying. 1) At witespyquad: m Select Flight Controllers. 2) MultiWii PRO 2.0 Flight Controller Board w/ GPS Option: m 3) Go to MWC 2.3: m 4 )At dropbox, MWC 2.3 files select: MEGA 2.0: MultiWii_MEGAEZ3_GPS_H...

bob195558

Hi waltr, Yes, I have, (Quick "HOW To RE-Flash' your board back to default .PDF Download) - (m). Its not working like the picture shows or I do not understand something. I am not sure what firmware to choose and/or am I maybe choosing the incorrect MultiWii 2.3 firmware. I want to upgrade the f...

bob195558

Hi Arakon and everyone, I have the MultiWii Board connected through USB to my Computer and down loaded Zip files from: m. I installed USB Drivers (CP210xVCPInstaller_x64.exe). MultiWii 2 0 USB connected_b.jpg I am not sure which firmware file I should use, But I tried: MultiWii_MEGAEZ2_GPS_HEX6X. Un...

bob195558

Hi Arakon,
Thank you for your quick reply.
I will make the changes and report back with them.
It's very late now, so I will work on it in the morning.

Bob

bob195558

Hi everyone, I am new to setting up MultiWii Boards and I am having difficulty understanding how to use the Arduino software. There seems to be a lot of options to choose when setting up MultiWii boards. I have a MultiWii PRO 2.0 Flight Controller w/ GPS Option (m) with MWC 2.2 on it from witespy an...

bob195558

Hi I have built a Quad using the MultiWii Pro V3 Flight controller board from WiteSpyQuad (Ready To Fly Quads) and I use a 9x Radio with erSky9x firmware with FrSky XJT Transmitter Telemetry Module with the FrSky D8R-XP Receiver w/ Telemetry. Is there a way to see the Sensor Readings on the MultiWii...

MultiWii

Search found 38 matches

Trouble installing MultiWiiConf JAVA error

Where did Witespy go ?

Re: Throttle throw incorrect with MultiWii Pro 1 Board

Re: Throttle throw incorrect with MultiWii Pro 1 Board

Re: Throttle throw incorrect with MultiWii Pro 1 Board

Re: Throttle throw incorrect with MultiWii Pro 1 Board

Re: Throttle throw incorrect with MultiWii Pro 1 Board

Throttle throw incorrect with MultiWii Pro 1 Board

Re: Direct Frsky telemtry data from MW FC

Re: Can MultiWii firmware be downloaded into Arduino ?

Re: MultiWii / Arduino / Error Compiling Problem !

Re: MultiWii / Arduino / Error Compiling Problem !

Re: MultiWii / Arduino / Error Compiling Problem !

Re: Direct Frsky telemtry data from MW FC

Re: Direct Frsky telemtry data from MW FC

Re: Direct Frsky telemtry data from MW FC

Re: Can MultiWii firmware be downloaded into Arduino ?

MultiWii / Arduino / Error Compiling Problem !

Re: Can MultiWii firmware be downloaded into Arduino ?

Re: Can MultiWii firmware be downloaded into Arduino ?

Re: Can MultiWii firmware be downloaded into Arduino ?

Re: Can MultiWii firmware be downloaded into Arduino ?

Can MultiWii firmware be downloaded into Arduino ?

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Re: Need Help Flashing MultiWii 2.2 to 2.3

Need Help Flashing MultiWii 2.2 to 2.3

Re: Direct Frsky telemtry data from MW FC