Search found 9 matches

by wobbletop
Thu Oct 23, 2014 3:21 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380990

Re: Naze32 hardware discussion thread

Thanks KC_703 I am still struggling to load local hex file this is what happens i browse to baseflight hex open upper status bar reads local firmware loaded etc 0 bytes ??? press flash, erros stm32 timed out or no bootloader found ,Tried shorting pads while powering up and flashing but no joy flash...
by wobbletop
Thu Oct 23, 2014 3:18 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380990

Re: Mag sensor defective?

timecop wrote:Thanks, this has been fixed, new hex uploaded


Thanks,
set mag_hardware = 3
turns off the MAG sensor (red instead of green).

Also, now in the setup screen, the model follows the movement of the quad and doesn't try to slowly return to the initial orientation. Neat.
by wobbletop
Tue Oct 21, 2014 11:50 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380990

Re: Mag sensor defective?

Not sure if it works, but there was a recent addition "set mag_hardware = 0" scouring through the code, it looks like "3" disables. Again, I'm not sure if it works... Guess it should make the MAG turn red in Baseflight Configurator if it works. EDIT: Nevermind... option 3 looks ...
by wobbletop
Tue Oct 21, 2014 9:40 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380990

Re: Mag sensor defective?

mag lines jumping around in sensor graphs = its toast. remove it + use external or just don't enable anything mag related (i.e headfree etc) The configurator still thinks the MAG is working. Is there a way to tell it not to use the MAG sensor? I ask as the model view in the configurator will always...
by wobbletop
Thu Oct 16, 2014 6:37 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380990

Mag sensor defective?

rev5 red board, latest firmware Previously I notice the mag sensor was acting erratic. The model image in the configurator would jump around and the raw sensor data for MAG would have drastic swings with the quad stationary. Now, there is no change in the MAG sensor data unless I bring a magnet clos...
by wobbletop
Thu Apr 10, 2014 4:33 pm
Forum: Getting Started - MultiWii config and setup
Topic: Call for full PID settings tutorial!!
Replies: 44
Views: 28100

Re: Call for full PID settings tutorial!!

Tuning PID like : set I&D=0, increase P until wobble, reduce a bit, set D to reduce overshoot, finally add some I to keep steady state… is true for a « conventional/classic/standard » PID control loop : m Tuning pid values in multiwii is not that intuitive as we don’t really know how the PID co...
by wobbletop
Thu Sep 05, 2013 4:29 am
Forum: Connecting elements
Topic: Possible to connect GPS over BT?
Replies: 3
Views: 1659

Re: Possible to connect GPS over BT?

It's a 5hz GPS. I don't think the BT mouse can be switched to host mode though. Can the BT dongle be a host?

This is the BT dongle...
http://www.rctimer.com/product_764.html
by wobbletop
Wed Sep 04, 2013 4:44 am
Forum: Connecting elements
Topic: Possible to connect GPS over BT?
Replies: 3
Views: 1659

Possible to connect GPS over BT?

I have the HK multiwii 328P along with a BT dongle. I've been able to connect my android phone to it with Multiwii EZ-GUI. I also have one of these... m It's a BT GPS "mouse". Is it possible for the multiwii to communicate with the BT mouse to get gps coordinates? I thought I'd ask since I...
by wobbletop
Fri Jun 07, 2013 4:44 am
Forum: Shields, boards and sensors
Topic: Multiwii Lite V1.0 help, please
Replies: 5
Views: 3104

Multiwii Lite V1.0 help, please

Hi all, Trying to get my tri setup. I had a KK2 but it died after a few minutes (another story) and now it's back ordered anyway. So I wanted to start with a cheap flight controller with no LCD to make it more robust. I bought this FC from rctimer, and didn't buy a FTDI controller with it. I did get...