Search found 19 matches

by flye
Tue Dec 02, 2014 10:45 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1379924

Re: Naze32 hardware discussion thread

Hi,I have a new afromini that don't arm since temp. is below+10
Get it inside it's ok and as soon it get outside and keep Taranis inside to be sure not a pot problem it don't arm
Altitude hold on this board never worked it fall like a rock wken on
I have 3 other mini working fine
This one is new!
by flye
Tue May 27, 2014 2:36 pm
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Re: Afromini don't arm

Resolved for anyone else looking for:I lower my emdpoint to 1996
by flye
Tue May 27, 2014 1:59 pm
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Re: Afromini don't arm

Got it to arm with switch aux 2 but not very usefull like that!
by flye
Tue May 27, 2014 1:31 pm
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Re: Afromini don't arm

Yes PPM correct,all channel work fine in GUI,accel calibrated on level
I have a naze 32 acro so i used to calibrate everything
I also used multiwii for 3 years now on different boards...
by flye
Tue May 27, 2014 11:20 am
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Re: Afromini don't arm

Thanks,try this but without success

Desesperate to make it fly!
by flye
Mon May 26, 2014 6:44 pm
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Re: Afromini don't arm

Thanks I know now why red led sometimes disapear Channel order ok PPM enabled In configurator I see all my channel working # dump Current Config: Copy everything below here... aux 0 8 aux 1 4 aux 2 1 aux 3 0 aux 4 0 aux 5 0 aux 6 0 aux 7 0 aux 8 0 aux 9 0 aux 10 0 aux 11 0 aux 12 0 aux 13 0 aux 14 0...
by flye
Mon May 26, 2014 4:38 pm
Forum: Boards
Topic: Afromini don't arm
Replies: 10
Views: 4098

Afromini don't arm

I can't find led status of afromini,are they the same as naze 32 acro? On mine when I power up blue led is on but no green led (don't know if there is one) when I tilt it... Red led come on when Taranis is on (with D4r 11 ) can't arm my rudder go from 998 to 2010 center 1500 throttle 996 Thanks for ...
by flye
Tue Apr 15, 2014 8:23 pm
Forum: Boards
Topic: How to setup failsafe on Naze32?
Replies: 10
Views: 8340

Re: How to setup failsafe on Naze32?

Hi,I have enabled failsafe and all I get is anything to off like set on my frsky rx
How can I set it to failsafe delay to let the quad descend slowly like in the MW code:
#define FAILSAFE_DELAY 10
#define FAILSAFE_OFF_DELAY 200
#define FAILSAFE_THROTTLE (MINTHROTTLE + 200
by flye
Tue Mar 26, 2013 10:15 pm
Forum: Shields, boards and sensors
Topic: i2c error
Replies: 2
Views: 1636

Re: i2c error

Thanks will check that but I only plug it to check if it was ok because I have had 3 faulty one before so they have not loaded the right config on it!
by flye
Sat Mar 23, 2013 3:57 pm
Forum: Shields, boards and sensors
Topic: i2c error
Replies: 2
Views: 1636

i2c error

I just received a new MultiWii Lite Edition Flight Controller V1.0 from rctimer with mpu6050 and I connect it,in gui 2.1 all sensors reading are ok but I get i2c error!Nothing else connected just ftdi to pc!
What does that mean?
by flye
Wed Sep 05, 2012 2:43 am
Forum: General discussions
Topic: frsky channel not working
Replies: 5
Views: 2225

Re: frsky channel not working

Is it possible that the problem come from crius multiwii se v1?
by flye
Sun Sep 02, 2012 3:00 am
Forum: General discussions
Topic: frsky channel not working
Replies: 5
Views: 2225

Re: frsky channel not working

So multiwii is not comatible with frsky?
by flye
Fri Aug 31, 2012 2:05 pm
Forum: General discussions
Topic: frsky channel not working
Replies: 5
Views: 2225

frsky channel not working

I have post this on rcgroup without result!: Hi,I have a fsth9x with dht and trying to use vd5m on my new microquad with crius multiwii se v1 on 2.1 and my receiver channels don't follow where I connect them I must change elev with throt and roll stay on gear no matter what I try I assign ch1 rud ch...
by flye
Mon Apr 30, 2012 9:06 pm
Forum: MultiWii tweaking - flying experience
Topic: fast esc
Replies: 0
Views: 774

fast esc

Is multiwii supporting fast esc?
by flye
Thu Apr 14, 2011 6:47 pm
Forum: Shields, boards and sensors
Topic: mega 1280 with wm+
Replies: 4
Views: 2290

Re: mega 1280 with wm+

OK - tested with MEGA 1280 and a genuine WM+ I connected to 5V and GND and SDA / SCL Downloaded 1.7 final and opened the file in Arduino IDE. selected the mega 1280 board and uploaded it. Then I started GUI and it worked right away internal i2c pullups enabled if it helps... Now Im gonna find all p...
by flye
Thu Apr 14, 2011 5:06 pm
Forum: Shields, boards and sensors
Topic: mega 1280 with wm+
Replies: 4
Views: 2290

Re: mega 1280 with wm+

Thanks Undcon,I have tried my wm+ on an arduino pro mini clone with clone adapter all was ok except when I connect rx and + from an esc and connect to pc I have lost voltge from esc to rx and I wonder if my wm+ is damaged..........and this mega was used with aeroquad board and gyroscope stop working...
by flye
Wed Apr 13, 2011 8:45 pm
Forum: Shields, boards and sensors
Topic: mega 1280 with wm+
Replies: 4
Views: 2290

mega 1280 with wm+

I have tried to connect an original wm+ on my arduino mega 1280(sda on sda, scl on pin scl of arduino,vcc+on 5v power pin and gnd on gnd beside 5v and on configurator preter7 I get nothing........
Any idea?
by flye
Wed Apr 13, 2011 3:21 am
Forum: Shields, boards and sensors
Topic: multiwii software on aeroquad shield
Replies: 5
Views: 3365

Re: multiwii software on aeroquad shield

Hi Flye, I am running MultiWii on my aeroquad hardware. The latest code has support for BMA180 accel, ITG3200 gyro etc. All you need to do is uncomment the defines for the sensors you have and change the ITG3200 gyro address from D0 to D2 and switch ROLL and PITCH values for all the sensors you are...
by flye
Tue Apr 12, 2011 5:00 pm
Forum: Shields, boards and sensors
Topic: multiwii software on aeroquad shield
Replies: 5
Views: 3365

Re: multiwii software on aeroquad shield

Hi, I have a quad built using a mega 2560 and an aeroquad shield m it uses a ITG-3200 3 axis gyro a BMA180 acc and a BMP085 barometer. motors KDA 20 28 1050 kv at 550 mm motor to motor Hobbywing pentium 18 amp ESC 10x3.8 APC props Firmware Aeroquad v2.1 After a lot of messing around getting the sof...