MultiWii

Hi,I have a new afromini that don't arm since temp. is below+10
Get it inside it's ok and as soon it get outside and keep Taranis inside to be sure not a pot problem it don't arm
Altitude hold on this board never worked it fall like a rock wken on
I have 3 other mini working fine
This one is new!

Resolved for anyone else looking for:I lower my emdpoint to 1996

Got it to arm with switch aux 2 but not very usefull like that!

Yes PPM correct,all channel work fine in GUI,accel calibrated on level
I have a naze 32 acro so i used to calibrate everything
I also used multiwii for 3 years now on different boards...

Thanks,try this but without success

Desesperate to make it fly!

Thanks I know now why red led sometimes disapear Channel order ok PPM enabled In configurator I see all my channel working # dump Current Config: Copy everything below here... aux 0 8 aux 1 4 aux 2 1 aux 3 0 aux 4 0 aux 5 0 aux 6 0 aux 7 0 aux 8 0 aux 9 0 aux 10 0 aux 11 0 aux 12 0 aux 13 0 aux 14 0...

I can't find led status of afromini,are they the same as naze 32 acro? On mine when I power up blue led is on but no green led (don't know if there is one) when I tilt it... Red led come on when Taranis is on (with D4r 11 ) can't arm my rudder go from 998 to 2010 center 1500 throttle 996 Thanks for ...

Hi,I have enabled failsafe and all I get is anything to off like set on my frsky rx
How can I set it to failsafe delay to let the quad descend slowly like in the MW code:
#define FAILSAFE_DELAY 10
#define FAILSAFE_OFF_DELAY 200
#define FAILSAFE_THROTTLE (MINTHROTTLE + 200

Thanks will check that but I only plug it to check if it was ok because I have had 3 faulty one before so they have not loaded the right config on it!

I just received a new MultiWii Lite Edition Flight Controller V1.0 from rctimer with mpu6050 and I connect it,in gui 2.1 all sensors reading are ok but I get i2c error!Nothing else connected just ftdi to pc!
What does that mean?

Is it possible that the problem come from crius multiwii se v1?

So multiwii is not comatible with frsky?

I have post this on rcgroup without result!: Hi,I have a fsth9x with dht and trying to use vd5m on my new microquad with crius multiwii se v1 on 2.1 and my receiver channels don't follow where I connect them I must change elev with throt and roll stay on gear no matter what I try I assign ch1 rud ch...

Is multiwii supporting fast esc?

OK - tested with MEGA 1280 and a genuine WM+ I connected to 5V and GND and SDA / SCL Downloaded 1.7 final and opened the file in Arduino IDE. selected the mega 1280 board and uploaded it. Then I started GUI and it worked right away internal i2c pullups enabled if it helps... Now Im gonna find all p...

Thanks Undcon,I have tried my wm+ on an arduino pro mini clone with clone adapter all was ok except when I connect rx and + from an esc and connect to pc I have lost voltge from esc to rx and I wonder if my wm+ is damaged..........and this mega was used with aeroquad board and gyroscope stop working...

I have tried to connect an original wm+ on my arduino mega 1280(sda on sda, scl on pin scl of arduino,vcc+on 5v power pin and gnd on gnd beside 5v and on configurator preter7 I get nothing........
Any idea?

Hi Flye, I am running MultiWii on my aeroquad hardware. The latest code has support for BMA180 accel, ITG3200 gyro etc. All you need to do is uncomment the defines for the sensors you have and change the ITG3200 gyro address from D0 to D2 and switch ROLL and PITCH values for all the sensors you are...

Hi, I have a quad built using a mega 2560 and an aeroquad shield m it uses a ITG-3200 3 axis gyro a BMA180 acc and a BMP085 barometer. motors KDA 20 28 1050 kv at 550 mm motor to motor Hobbywing pentium 18 amp ESC 10x3.8 APC props Firmware Aeroquad v2.1 After a lot of messing around getting the sof...