MultiWii

Thank you both for your replies... I have been using the 10'' 3 blade for two reasons: first I cannot find larger 3 blade , second I am TOTALLY stucked at 3 blade config as I can balance them dynamically to almost ZERO vibration and maybe that's why as michelsneto states I can get pretty high number...

My experience is the same when upgraded to 6s and 380kv motors... for some reason even with perfectly balanced props i had strange oscillations and behavior... When i was holding it with my hand i could feel some kind of resonance which i couldn't explain as every single motor was turning very quiet...

Hi to all, i am running multiwii 2.4 on a CRIUS AIOP v2, F450 frame, 6S, 380KV motors on 10x4.5 3-blade props Trying to adjust ALT HOLD from zero, i am having some questions... Most of the guides say to start from D value which adjusts Z ACC sensitivity, then P (for the baro sense) and finally I for...

a BIG THANKS!!!

Hi there, i would like to ask if someone knows how to set up the deadspan of GPS Position hold. In the conf there is a default number 40. What is this represents? Is it servo channel value added from the 1500 mid point etc? How low can i set it so when i move the craft even a little to register the ...

Thanks... this is what i did before reading your post.. now from mini GPS seems to be setup on 115200 and 10Hz... but is it really supports it as EOSBandi mentioned before?

Hi, running multiwii on the above board which have extra eeprom for logging... is it somehow used from multiwii code? Any help or documentation on that?

Thanks in advance!

Hi, i don't know if in someway it can be accomplished with the current version... But i have installed everything tied up all cables and protected the FC in the middle... It's SO DIFFICULT, if for any reason i need to do a dynamic balance!!!! If only i had the option to turn off individual motors/ou...

no.. just tried a failed update and managed to flash AXN1.30 2389...

Thanks for your answer!! I am trying to flash the 1.9 to my module but seems doesn't accept!!.. Its the HK module (GS-15c)... i can only flash AXN1.30 2389... any suggestions?

Hi to all, just upgraded from HK MultiWii Pro red board to Crius AIOP v2.0 as Crius has more pins, better pcb, and used the same MTK3329 GPS.. But also upgraded to MWii 2.2 and i am a little bit confused with GPS setup... Do i need to have defined the INIT_MTK always? Although GPS seems to work fine...

Hi, tested today 2.2 and have two questions... ANGLE mode seems not to be engaged (GUI).. only HORIZON gets Green when set to aux... Checking MTK3329 gps which worked on 2.1 now doesn't work.. Do i have to define NMEA and initialize MTK GPS commands? binary mode is better? All other stuff seems OK!....

Could someone help with MTK3329 which is supplied with HK Multiwii pro ( http://www.hobbyking.com/hobbyking/store/__26588__MultiWii_PRO_Flight_Controller_w_MTK_GPS_Module.html )board? Which is the best firmware up to now for Multiwii 2.1/2.2? How can i confirm my settings and refresh speed? Thanks i...

Hi thanks for your answer.. real pin 32 on 2560 is GND actually!... Do you have the same board? (HK) After many searching i managed to make it beep!!!! D8 output on HK Red board goes to 17 actual pin of 2560 so in def.h file the original part is this: #define BUZZERPIN_PINMODE pinMode (32, OUTPUT); ...

Here another owner of this board.. posted already some threads with some questions... First impressions are super, as this flies really well with ready made code on Q450 frame... some fine tunning and should be perfect!!.. Today tried with about 6 Beaufort air and the ALT HOLD worked really well +/-...

Hi Greeks, George from Iraklion... HK Multiwii pro with MTK gps on ver 2.1

Hi to all... first, a BIG THANKS to all developers out there who provide us their work!... Trying my first multiwii system i bought the HK board (red one) and have spent many hours by reading and reading! I want to enable BUZZER option and later some other extra features... BUT after many tries i fi...

Hi to everyone, i am very happy getting into multiwii world!.. Just started with MultiWii with MTK Gps from HK and i was very impressed just out of the box!... Running 2.1 with default settings i am facing a serious problem though... Have quad mode x 4 motors NTM2826 8X4 and 30A plush SPD. The quad ...