Search found 30 matches

by juanquy
Tue Oct 03, 2017 3:43 am
Forum: Software development
Topic: MWii development beyond v2.4
Replies: 73
Views: 20116

Re: MWii development beyond v2.4

YEAH!!!! Good News!
by juanquy
Fri Mar 17, 2017 6:01 am
Forum: Shields, boards and sensors
Topic: Crius AIO Pro v2 motors showing power while not armed
Replies: 1
Views: 995

Re: Crius AIO Pro v2 motors showing power while not armed

Re calibrate ESC ?
Check if that channel is reverse on ur TX?
Check TX mid point is 1500 ?

no idea
I have the same board but I think I runningMW v2.3 or maybe v2.2

good luck with that.
JC
by juanquy
Sat Jan 14, 2017 6:12 am
Forum: Software development
Topic: 2.4 is finally here :)
Replies: 71
Views: 70499

Re: 2.4 is finally here :)

hey I want to give it a try to you fork, do you have a config file for a CRIUS AIOP V2? Can't find my file :( i think my son deleted it, I'm runing V3 with GPS support.
by juanquy
Fri Dec 30, 2016 11:13 pm
Forum: Software development
Topic: 2.4 is finally here :)
Replies: 71
Views: 70499

Re: 2.4 is finally here :)

Now what?
by juanquy
Fri Sep 04, 2015 6:13 pm
Forum: Buy & Sell
Topic: Selling my 450 trainer.
Replies: 0
Views: 1005

Selling my 450 trainer.

Hi guys, I'm selling my 450 quad trainer, It have new motors and prop, less than 15min flight time . Its a very hard frame, the flight controller is a HK SE v2 runing MW v2.3. It was a very good starter Quad when I was learning. I also have 2 or 3 spare arms. I was planing teach my son how to fly bu...
by juanquy
Tue Jul 28, 2015 2:25 pm
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

Hey fellas sorry I been out of town I will upload the file next week and. Sorry.
by juanquy
Thu Jul 16, 2015 11:35 pm
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

The Forum it not allow me to paste the code, weird, I will try this weekend to see, Have a nice vacations!!! enjoin and relax!

tar.gz is the file compressed in Ubunto Linux, its ok I will try to post it this weekend, and I will wait, its to hot here to flight.

regards

JC
by juanquy
Wed Jul 15, 2015 5:09 am
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

Sure, this is my conf.h
I hope its what u are thinking this is kinda annoying me already.

regards
JC
by juanquy
Mon Jul 13, 2015 12:48 am
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

Sorry I forgot to post that, I also try moving funtions,and still the same. I try v2.4 in a old HK 328p FC and it work perfect, I think it's something relate to the Crius AIOP v2 and MW 2.4 code. Guys honestly I spend all night long working on it and experimenting trying to figure it out. At this po...
by juanquy
Sat Jul 11, 2015 7:52 pm
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

Hi guys Thank you, I'm not using GPS for way points or autonomous flight, just to gps hold and home, I been using this features with v2.3 I dont need EOSBandi version cuz as I said not using autonomous navigation or autopilot. I will upload another video so you guys can see it working in v 2.3 perfe...
by juanquy
Sat Jul 11, 2015 2:40 am
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Re: Crius AIOP V2 aux 2 not working in MW 2.4

CK thanks for your interest: Aux2 is in the Aux2 pin on the board, not 12 or 8, as I said if I flash the board with v2.3 it work perfectly, but when I flash it to 2.4 stop working, you can see radio signal in Aux2 in the radio channels tab but nothing activating, here is a YouTube video so you can s...
by juanquy
Wed Jul 08, 2015 6:01 am
Forum: Getting Started - MultiWii config and setup
Topic: Crius AIOP V2 aux 2 not working in MW 2.4
Replies: 14
Views: 905

Crius AIOP V2 aux 2 not working in MW 2.4

Hi guys: Finally I had the time to upgrade to MW 2.4 from v2.3 My quad is a 450 spider frame with a Crius AIOP V2 + GPS. In v2.3 everthing work perfect, in 2.4 I cant get my aux2 to work at all, you can see in MWConfig RC channel working, but in the fly modes window nothing happen, my Aux 1 is to ac...
by juanquy
Sun Mar 09, 2014 9:10 am
Forum: Software development
Topic: KV Team Multiwii OSD
Replies: 1021
Views: 142302

Re: SW Development on Minim Osd

SOLVED !!! It was the Arduino version. thanks JC Please help: I have this compiling error: Error compiling: In file include from KV_Team_OSD.ino:28:0: GlobalVariables.h:714:32: error: variable 'item_table' must be const in order to be put into read-only section by means of '__attribute__((progmen)) ...
by juanquy
Sun Mar 09, 2014 7:59 am
Forum: Software development
Topic: KV Team Multiwii OSD
Replies: 1021
Views: 142302

Re: SW Development on Minim Osd

Please help: I have this compiling error: Error compiling: In file include from KV_Team_OSD.ino:28:0: GlobalVariables.h:714:32: error: variable 'item_table' must be const in order to be put into read-only section by means of '__attribute__((progmen)) ' KV_Team v2.3 Ubuntu 13.10, Arduino IDE 1:1.0.5+...
by juanquy
Fri Aug 02, 2013 12:24 pm
Forum: Getting Started - MultiWii config and setup
Topic: Rare behavior Please Help!!
Replies: 2
Views: 240

Re: Rare behavior Please Help!!

I will, let see what happen.
by juanquy
Fri Aug 02, 2013 2:37 am
Forum: Getting Started - MultiWii config and setup
Topic: Rare behavior Please Help!!
Replies: 2
Views: 240

Rare behavior Please Help!!

My 450 quad was flying perfect with MW 2.2 and Turnigy 9x TX and 9x V.2 RX until I decide to replace my motors Bearings( they were really bad LOL) and my TX for a Turnigy 9xr with a FrSky module DJT and RX is a V8FR-II ( non Telemetry) binded with TX = D_mode . The motors and props are balanced and ...
by juanquy
Mon Mar 18, 2013 6:12 am
Forum: Software development
Topic: MultiConf Port to Android TabletWifi
Replies: 71
Views: 6080

Re: MultiConf Port to Android

WOW you did it!!! I have your app running in 4 Android devices of course with a magnifying glass so congratulation but still loving Ezio App. salutos, saludos JC Read Ezio posts here (Forums/Software/Multiwii EZ GUI) and you will find a direct link to the apk... good look porting from Processing to ...
by juanquy
Sun Mar 17, 2013 2:54 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

Here is a link "Supporting Multiple Screen"
http://developer.android.com/guide/prac ... pport.html
and I love the actual GUI.
by juanquy
Sun Mar 17, 2013 12:14 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

Well sorry if I sound stupid but I need to understand what do you means.
MWI already use UART/TTL for comm
by juanquy
Sat Mar 16, 2013 6:54 pm
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

I agreed about the Tablet layout. It could be a option in Ez GUI Config Menu.
by juanquy
Sat Mar 16, 2013 6:07 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

He is right, my plan is buy this cheapo Table to use at the field :
http://www.tmart.com/10.1-Capacitive-To ... 68668.html
It have a Host USB type A so it will be easy plug a APC220 or 3DR radios
by juanquy
Fri Mar 15, 2013 5:33 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

YAY!!!!!!! do you already bought the OTG cable ? I think I have 2 or 3 here in my cave.
by juanquy
Fri Mar 15, 2013 5:27 am
Forum: Software development
Topic: MultiConf Port to Android TabletWifi
Replies: 71
Views: 6080

Re: MultiConf Port to Android

Read Ezio posts here (Forums/Software/Multiwii EZ GUI) and you will find a direct link to the apk... good look porting from Processing to Android.
by juanquy
Sun Feb 10, 2013 9:03 pm
Forum: Software development
Topic: WinGUI 2.1 Beta is released for testing
Replies: 96
Views: 8725

Re: WinGUI 2.1 Beta is released for testing

Here is WinGUI 2.0 running over Ubuntu 12.04, PowerPC970 Quad ( PowerMac) and Mono, its not ready yet I have to work wiith the GUI cuz it look bad but it WORK!! so if you are a linux user you can use it.
Its a way I can have the 2.1 source code?
by juanquy
Sun Feb 10, 2013 8:52 pm
Forum: Getting Started - MultiWii config and setup
Topic: WinGUI & Windows2000???
Replies: 10
Views: 576

Re: WinGUI & Windows2000???

Actually WinGUI is running over Ubuntu (Linux) Here is a image of WinGUI running over Ubuntu 12.04 AND PowerPC970 Arch!!! EOSBandi I have some questions about the source code, the one I have here is version2.0 I know the 2.1 is running already, its a way I can have it? I'm using MonoDevelop so far I...
by juanquy
Wed Jan 30, 2013 11:36 pm
Forum: Shields, boards and sensors
Topic: 3DR Radio 433 MHz on MultiWii
Replies: 16
Views: 12173

Re: 3DR Radio 433 MHz on MultiWii

Hi guys:
Its possible to connect a APC220 to a CRIUS Multiwii SE V2 for telemetry ?

thanks in advance
JC
by juanquy
Wed Jan 30, 2013 11:18 pm
Forum: Ideas
Topic: MAVLink protocol
Replies: 21
Views: 11607

Re: MAVLink protocol

HI:
I can compile your code on Linux?
if yes please provide me how to , tools and lib I need it to do it
thanks
jc
by juanquy
Sun Jan 06, 2013 4:09 am
Forum: Software development
Topic: MultiWii EZ-GUI
Replies: 1434
Views: 230018

Re: MultiWii EZ-GUI

Help!!It shutdown ( turn off) my Thunderbolt !!! OS Android 4.0.3