MultiWii

yes i had ppm enabled and gps

no its working!! (not ppm tho.. using a million wires):) it was the receiver
I think I just need to get another radio system soon spektrum blows!

BTW hes a link to the receivers page
http://www.lemon-rx.com/shop/index.php? ... duct_id=66

Ok so wouldnt i map it from the receiver in the order like this states above "Aileron, AUX, Gear, Elevator, Throttle and Rudder" or do i stick with the spektrum order TAER1234 if i had another radio system like a 9x i would go that route, but im kinda stuck using this receiver with ppm out...

I finally got a hold of a ppm/uart receiver, to try and take advantage of more inputs like gps and connect using one wire im kinda lost tho I set my channel mappings (cli) to match the listed order or my orange/lemon rx A21ETR34 heres what the receiver says its outputs are: - TX port (UART, 9600bps,...

hey timecop i found this today, think something could be ported to it with an onscreen calibration interface or diagnostics m I know its large but for those big multirotors be kinda neat some photos http://img03.taobaocdn.com/imgextra/i3/31032630/T2U7JqXklXXXXXXXXX_!!31032630.jpg http://img04.taobao...

I did the update using the program from the screenshot and yeah when I tilt it, it blinks when I move it until level again Until I tried the update tonight, it was'nt doing the motor lock on thing, I did the update because my settings were changed so much, I figured I could revert back to defaults a...

well I have'nt been enabling level to try it, what I said is the switches worked to enable it and to arm prior to using the throttle, after the motors spin up with throttle(while armed) they stay on, after about 15 seconds nothing works, the motors keep going on there own(about 3/4 speed) , no matte...

Ok thanks it might have been off level where I tested it perhaps I messed things up again ,now it comes on and wont unthrottle or disengage the motors after a few seconds working past the mid throttle point The only way to get it to stop is to kill all power and restart it even the switches dont do ...

Here you go

I set mine to what my radio reads on the live readings:

midrc = 1521
minthrottle = 995
maxthrottle = 1928
mincommand = 1000
mincheck = 993
maxcheck = 1936

i wasnt sure about the min/maxcheck so i set them to my switch low and high points

Ok I did the midrc thingy in the cli and so far it seems to be ok (Thanks! ) when I lift off, it raises higher on the rear end, tilting forward, with just a slight touch of the right stick back will hold it even , I just need to get home to connect back up and adjust something, I'll have to do some ...

Well my problems were not related to endpoints or limits at the time that was wrote, I was trying to get it working period, the windows flash would not work from my computer so I tried to get the dos version commandline flasher to work, until I finally was told the thread was moved to here and the f...

What makes the google search tricky is you end up with conflicting results where people have troubleshooted there problems and came up with didferent solutions related to their hardware , that is fine if you also have the same, in the same aspect you get solutions related to older code that have cha...

I will try again to google it, I have even used youtube , I need a better radio.. I find more each day Would a dx8 be better? I can trade my heli for one ,seeing i never flew it yet either i guess i should have got the 9x long ago, I have so many spektrum receivers tho been holding off The hard part...

you are talking about the pdf manual right?... I cant seem to find any other one I have tried everything to get them to 2000 and have had no luck even using my settings on max (+125/-125) on the transmitter, the highest i can get them is like 1720 perhaps it's just im used to just adjusting flaps or...

Thanks that explains my problems ,they are 30a plush i thought they were 40, I'm also using a spektrum AR6100E This hardware does not support turnigy plush esc. and I did'nt think the dx6i had radio settings for multiwii anyway, I read the manual and the naze32 manual ,unless its in a specific threa...

I have unflashed turnigy 40a plushes and a dx6i not sure about end points, they go as low as 900 and as high at 1700 on the screen gui

Is there a specific way to calibrate my throttle limits ,different than most fc's
I have been told to do them individually via the receiver then reattach to the naze, and someone else said to do them at once through the naze

Im confused now

(naze32 Green Board ...v2 maybe?)

It worked thanks!!!!

I so did'nt want to revert to my kk5.5

Thanks again
Charles

Thanks!! Is the newer version listed on the first page? my main problem has been java, I cant install it on my machine and my user profile management has kept me from installing some non java related apps too (unsupported charicters in my username) Up until recently I could'nt get anything other tha...

Is there a gltch sometimes where you can't ARM with a switch but you can via the stick? I have tried numerous channel mappings and can control ACC on aux1 or aux2 (and both) via my gear or flap switch but not ARM Screenshots attached showing various attemps and min/max limits of switches http://stat...

ive looked all over here and cant seem to find any reference to the em406 gps that i have as a spare from my ardupilot does anyone know if it can be fed in/out of the tx/rx leads on the bottom, as im using the octorpus of wires from receiver using chans 3 and 4 ive looked at the spec sheets and it s...