Search found 15 matches
- Thu Nov 06, 2014 10:30 pm
- Forum: Boards
- Topic: Afromini don't arm
- Replies: 10
- Views: 4130
Re: Afromini don't arm
THANKS! lowering my Th endpoint worked for me too
- Thu Nov 14, 2013 10:38 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
Well done
- Wed Dec 12, 2012 2:55 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
understood that part
- Wed Dec 12, 2012 1:30 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
ok i will try, but since i´m a completly noob on this, what´s the program name to modify the code? i have to modify the Baseflight.hex right? (sorry if this questions are stupid..but i don´t know nothing about codeing) if it is only change that i will try. Or maybe if is easy for you, could you send...
- Tue Dec 11, 2012 5:35 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
Not unless you're willing to change the code (edit the PWM map and assign camera servos somewhere else). Hardware can do it, but not in the default configuration. Ummmmm... Chinesse to me. Even only one servo? ah maybe it´s only changing the channel assignment map? is not right? that pwm will be th...
- Mon Dec 10, 2012 7:50 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
one question more. In Tri-copter mode, tail tilt servo connects to S1, and motors M1..M3 as you said in the manual, can i use camera stabilization on roll and pitch? (Maybe only one? on S2) It is enabled on CLI but i´ve tried conecting new servo to s2 and get any movement when i move the tri. came s...
- Thu Dec 06, 2012 2:20 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
Your RC endpoints should be 1000..2000,,, if it's not activating acctrim you're probably way below that. This stuff IS in the manual, or at least in general multiwii wiki. Your first step should be endpoints to 1000..2000 and subtrim center to 1500 (or 1520 on futaba). yes, i have like that, end po...
- Wed Dec 05, 2012 9:58 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
Yes i tried after I post that message, and yes It flies better, maybe a need down a little more P, but in Acro is perfect, maybe a bit less.
But the main problem is to not be able to trim the acc or calibrate through sticks commands
But the main problem is to not be able to trim the acc or calibrate through sticks commands
- Wed Dec 05, 2012 7:07 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
hi again, i setting up my old tricopter (before naze it had KK), i don´t know if i may ask this here, but i can´t get the acc adjust with the sticks. While dissarm, full throttle and full back elevator, to calibrate acc. To trim it, full throttle and right stick to compensate the movement. The light...
- Wed Dec 05, 2012 3:24 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
got it. Unmark the yaw direction block and reverse the rudder
(on Naze32 wii configurator for mac, its -1 )
(on Naze32 wii configurator for mac, its -1 )
- Wed Dec 05, 2012 3:11 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
Somebody knows what i have to change in settings to reverse the yaw gain? where is it call, yaw gain or something liket this? i can´t find it.
it is compensating in the wrong way , and my TRIcopter spin around..
thanks
it is compensating in the wrong way , and my TRIcopter spin around..
thanks
- Sun Dec 02, 2012 4:50 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
no thanks, i already know it, XD
i always check the pdf rev when i have to mess with the imput on the board to not blow it
i always check the pdf rev when i have to mess with the imput on the board to not blow it
- Sun Dec 02, 2012 4:48 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
There are no "channel 1" or "roll", this is configurable by "MAP" command. Especially considering default settings of ch1 is NOT roll anyway, so that means you screwed with map command, mind posting your current channel mapping then? if i have regular imput to the FC o...
- Sun Dec 02, 2012 4:44 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
I don´t know what happened but it works perfect now
i don´t knwo if it matter but when it didn´t work, the board seem to be touching one screw on the botton, at that metal part near to the RC imput.. i don´t know, now its free of any contact
thanks anyway TC
i don´t knwo if it matter but when it didn´t work, the board seem to be touching one screw on the botton, at that metal part near to the RC imput.. i don´t know, now its free of any contact
thanks anyway TC
- Sun Dec 02, 2012 4:23 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1399399
Re: Naze32 hardware discussion thread
hello I have my second naze32 after lost one quad... but know setting this one (in a tricopter), it does not recognize the channel 1, i have no roll imput. I have tried to reflashing it with hercules and withh the flash loader, and it worked once until a closed the multiwii gui, but it does not work...